• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.3
• /
• pp.116-126
• /
• 2010

The Korean rolling stock safety regulation stipulates that the collision deceleration of a car body should be maintained under average 5g and maximum 7.5g during train collisions. One-dimensional dynamic model of a full rake train, which is made up of nonlinear springs/bars-dampers-masses, is often used to estimate the collision decelerations of car bodies in a basic design stage. By the way, the previous studies have often used some average force-deformation curve for energy absorbing structures in rolling stock. Through this study, we intended to analyse how much the collision deceleration levels are influenced by the initial peak force modeling in the one-dimensional force-deformation curve. The numerical results of the one-dimensional dynamic model for the Korean High-Speed Train show that the initial peak force modeling gives significant effect on the collision deceleration levels. Therefore the peak force modeling of the force-deformation curve should be considered in one-dimensional dynamic model of a full rake train to evaluate the article 16 of the domestic rolling stock safety regulations.

• ETRI Journal
• /
• v.19 no.1
• /
• pp.1-12
• /
• 1997

In this paper, we present an improved multicarrier direct sequence (DS) code division multiple access (CDMA) scheme by modifying the system originally proposed by Kondo and Milstein [13]. In this modified system, different spreading sequences multiplied by a data sequence modulate different carriers. This is to prevent the multiple access capability from reducing when the fading characteristics of different carrier frequencies are highly correlated. We have derived a formula which determines the mean values of the relative received signal strength in a single carrier DS CDMA rake system and in a multicarrier DS-CDMA system. We present results on the comparison of the bit error rate (BER) performance of the two systems including the effect of correlation between fading characteristics of different frequencies under various multipath fading conditions. The results indicate that with 50 users the modified multicarrier DS CDMA system can achieve an uncoded irreducible BER of $1.7{\times}10^{-3}$ with an average received signal-to-noise ratio per bit of 10dB, which is better that $3.0{\times}10^{-3}$ achieved by the single carrier DS CDMA rake system, and also show that if multicarrier CDMA system is used with respect to single carrier CDMA system, the SNR gain is up to 4.5 dB for the uncode BER of $10^{-3}$ being achieved.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.1
• /
• pp.29-37
• /
• 2005

One of the principal disadvantages of multicarrier modulation technique is the sensitivity to the frequency offset introduced by Doppler shift. This frequency offset introduces inter-carrier interference (ICI) among the multiplicity of carriers in the multicarrier modulated signal. However, Doppler spread induced by temporal channel variations can Provide another means for diversity. In this paper, we propose a modified multicarrier code division multiple access (CDMA) system to exploit Doppler diversity as well as multipath diversity. The key work of our framework is a canonical time-frequency-based decomposition of the mobile wireless channel into series of independent fading channel. The decomposition naturally leads to a time-frequency generalization of the Rake receiver that exploits both multipath and Doppler diversity.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.9
• /
• pp.55-62
• /
• 2003

This paper investigates the micro-cutting of cemented carbides using PCD (polycrystalline diamond) and PCBN (polycrystalline cubic boron nitride) cutting tools are performed with SEM direct observation method. The purpose of this study is to make clear the cutting mechanism of cemented carbides and the fracture of WC particles at the plastic deformation zone in orthogonal micro-cutting. And also to achieve systematic understanding, the effect of machining parameter on chip formation and machined surface was studied, including cutting speed, depth of cut and various tool rake angle. Summary of the results are shown below. (1) Three type of chip formation process have been proposed by the results of the direct observation in orthogonal micro-cutting of cemented carbide materials. (2) From the whole observation of chip formation, primary WC particles are crushed and/or fine grained in the shearing deformation zone. A part of them are observed to collide directly with a cutting edge of tool by following the micro-cutting. (3) Surface finish, surface morphology and surface integrity is good to obtain by cutting with PCD cutting tool compared with PCBN. (4) The machined surface has the best quality near the low cutting speed of 10${\mu}m$/sec with a cutting depth of 10 ${\mu}m$ using 0$^\circ$ rake angle and 3$^\circ$ flank angle in this condition, but it was found that excessively low speed, for example the extent of 1 ${\mu}m$/sec, is not good enough to select for various reason.

• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.2
• /
• pp.76-85
• /
• 1993

Based on the cutting force model, three-dimensional optimal design model was developed and optimal designed tool which is minimized cutting force is developed by computer simulation technique. In this model the objective function which is minimized resultant cutting force was used and the variables are radial rake angle, axial rake angle, lead angle of the tool. The cutting forces using conventional and optimal tools by simulation, are compared and analyzed in time and frequency domains. In time domain the cutting force of optimal tool in feed direction was more reduced and less fluctuated than that of conventional tool. Cutting forces of optimal tool in X-and Z-directions are shown a little increased than those of conventional tool. In frequency domain amplitude of insert frequency components of optimal tool in feed direction was more reduced than that of convent- ional tool. The amplitudes of insert frequency components of optimal tool in X-and Z-direction are a little increased than those of conventional tool. As the reduction of amplitude and fluctuations of the cutting force, Optimal tool is considered that tool life and surface roughness would be improved, and stable cutting would be expected.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.37 no.2
• /
• pp.75-82
• /
• 2000

In this paper, described is the comparison of performances based on the computer simulation under IMT-2000 environment between multicode and multicarrier CDMA system for the design of wireless systems using wideband CDMA technology. From simulation results, it can be concluded that both multicode and multicarrier CDMA scheme show comparable performances. Diversity scheme of RAKE receiver is indispensible for both multicode and multicarrier CDMA systems under IMT-2000 outdoor B and vehicular B channel environment. Either Hadamard matrix or PN sequence can be used as the orthogonal code as far as the orthogonality is kept. Finally, with increasing chip rate and less users, performance is getting better.

• Journal of the Korean Wood Science and Technology
• /
• v.16 no.4
• /
• pp.54-60
• /
• 1988

Machinabilities means inherent properties of pinus densiflora at Chunyang district to be CNC machined easily or not, and processing abilities of the tool and machine together. This explanation signifies that machinabilities have two phases of signification, depended on considering and stress either materials or tools preferentially. This paper discuss machinabilities, the following items are usually employed as the indices of stress distribution at the cutting tool rake face. The stress distributions on the chip - tool contact surface at the early stage of the chip forming and under the stage of fringe pattern in wood cutting were analyzed the photoelastic method. The tool used in the present experiment was the special cutting tool H.S.S. one made in laboratory. And isochromatic fringe pattern and isolinic line of work piece by chip-behavior during the cutting operation were photographed with the feed camera continuously. The effects on the stress, distribution on the rake face of the epoxy tool and the strain distribution in the work piece of wood plate by chip behavior are cleared in pre cent experiment.

• Journal of the Korean Society for Precision Engineering
• /
• v.8 no.3
• /
• pp.44-54
• /
• 1991

A Study was made on falnk wear in carbide tools in turning SUS304 steel. When an austenitic stainless steel (SUS304 steel) is cut with the tool, saw-toothed chip are produced. It is found that machining SUS304 steel would make a tool worn fast. For increasing productivity, tool wear has to be predicted and controlled. An amended cutting geometry consisting of a negative rake angle ($-6^{\circ}$ ) and a high clearance angle ($-17^{\circ}$ ) is proposed for decreasing carbide tool wear (flank) in the machining of SUS304 steel. The amended cutting geometry is found to make the flank wear lower than a general cutting geometry (rake angle $6^{\circ}$ , clearance angle $5^{\circ}$). The effects of the three cutting variables (cutting speed, feed, tool radius) on the flank wear analyzed by fiting a simple first-order model containing interaction terms to each flank wear parameter by means of regression analysis and the predicted from first-order regression analysis model equation of flank wear.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.24 no.7A
• /
• pp.996-1004
• /
• 1999

In this paper, we evaluate the performance of reverse link synchronous CDMA with orthogonal spreading and Rake combining, and compare this to that of an asynchronous transmission under Rayleigh multipath fading environments. The link performance is evaluated in terms of average bit error rate (BER) and capacity, assuming ideal BPSK data modulation. The focus of this paper is on the impact that the multipath intensity profile (MIP) shape and number of taps in Rake receiver have on the performance of synchronous transmission. The results show the reverse link synchronous transmission can always achieve smaller BER than the asynchronous transmission even if inter-path interference exists.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 1997.04a
• /
• pp.15-20
• /
• 1997

Source parameters of the December 13, 1996 Yeongweol earthquake are estimated using the grid test technique. Thirty polarities of P waves recorded at KMA, KIGAM, KSRS and JAPAN stations are used for the event. The obtained fault plane solution shows predominantly strike-slip motion with small amount of thrust component. The orientation of the fault is 180$\pm$10$^{\circ}$in strike, 50$\pm$5$^{\circ}$in dip and 150$\pm$5$^{\circ}$in rake, or 292$\pm$3$^{\circ}$in strike, 65$\pm$5$^{\circ}$in dip and 30$\pm$10$^{\circ}$ in rake. These solutions are very similar to those of earthquakes occurred at Sagju, Pohang and offshore Gunsan. The compressional axis of stress field is trending from ENE to WSW, which is consistent with the previously defined typical regional tectonic stress orientation in and around Korean Peninsula.. From the result of this study and other source mechanisms around the Korean Peninsula, we are of opinion that tectonic stress around the Korean Peninsula may be more attributed to the collision of Indian plate with the Eurasian plate than subduction of Pacific and Philippine plates.