• Korean Journal of Materials Research
• /
• v.21 no.10
• /
• pp.532-541
• /
• 2011

The Xe plasma flat lamp, considered to be a new eco-friendly LCD backlight, requires a further improvement of its luminance and luminous efficiency. To improve the performance of this type of lamp, it is necessary to understand the effects of the discharge variables on the luminous characteristics of the lamp. In this study, the luminous characteristics of a coplanartype Xe plasma flat lamp with a teeth-type electrode pattern were analyzed while varying the gas composition, gas pressure and input voltage. The effects of the phosphor layer on the discharge and the luminous characteristics of the lamp were also studied. The luminous efficiency of the coplanar-type Xe plasma flat lamp improved as the Xe input ratio and gas pressure increased. Higher luminous efficiency was also obtained when helium (He) was used as a buffer gas and when a phosphor layer was fabricated on the electrode region. In contrast, the luminous efficiency was reduced with increasing the input voltage. It was found that the infrared emissions from the lamp were affected by the Xe excitation rate in the plasma, the Xe gas density, the collisional quenching of excited Xe species by gas molecules, and the recombination rate between the Xe ions and electrons.

• Nuclear Engineering and Technology
• /
• v.53 no.11
• /
• pp.3717-3722
• /
• 2021

In this study, the recovery rates of the dissolution method for radioactivity analysis of expandable polystyrene (EPS) with a liquid scintillation counter (LSC) using tetrahydrofuran (THF), toluene, and acetone as solvents were estimated. The detection efficiency calibration curve for each solvent was derived. Two methods-the volumetric ratio method and the quenching agent method-were used to prepare quench source sets, and calibration curves were derived by linking the data from the two quench source sets. The R² value of the calibration curve for THF was found to be 0.984. The relationship between the mass of dissolved EPS and the quench level was estimated: the quench level increased as the mass of dissolved EPS increased. Premix and postmix dissolution methods were tested. The recovery rates using THF with the premix method were 84.9 ± 0.9% and 96.5 ± 1.5% for ³H and ¹⁴C, respectively. Furthermore, the stability of the recovery rate over time when using THF was evaluated. The dissolution method with the premixed solution exhibited a more stable recovery rate over time. The dissolution methods were found to be applicable for analysis using LSC, and THF was found to be the most suitable solvent for the proposed method.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.6
• /
• pp.10-16
• /
• 2021

Drilling is a crucial process that takes up a significant amount of weight during machining operations. In addition, drill tip-type tools and related operations have been developed for manufacturing industries to achieve economic efficiency. In this study, SM45C carbon steel, widely used for machine structures, was utilized as the working material after quenching and tempering. Insert-tip types of carbide tools, such as TiN and TiAlN, were used as tool materials. Drilling conditions such as the spindle revolution, feed rate, step of cut, and tool diameter were used to measure roughness, roundness, and straightness using the orthogonal array table statistical method. The surface roughness, roundness, and straightness characteristics based on the conditions were analyzed using ANOVA. The results showed that the spindle speed and feed rate were the main factors influencing carbide insert-tip drilling under the same conditions as the experimental conditions.

• Journal of Korea Foundry Society
• /
• v.27 no.6
• /
• pp.243-249
• /
• 2007

The effect of Re addition and solidification rate on the directional solidification behavior of Ni-Al model alloy has been investigated. Directional solidification (DS) were carried out using the modified Bridgman furnace with various solidification rates. The solid/liquid interface during directional solidification was preserved by quenching the specimen after the desired volume fraction of original liquid was solidified. The equilibrium partition coefficients of Al and Re Were estimated by measuring the compositions at the quenched solid/liquid interface. Then, the effect of Re addition on the elemental segregation behavior was carefully analyzed. The differential scanning calorimetry results showed that the Re addition results in increased ${\gamma}'$ solvus and freezing range of the alloy. It was also shown that the primary dendrite arm spacing gradually decreases with increasing the Re content, while the secondary dendrite arm spacing appears to be independent on the Re content. The compositional analyses clearly revealed that the segregation of Al increased with increasing the Re content and solidification rate, while that of Re was found to be independent on the solidification rate in the range of $10{\sim}100{\mu}m/s$ due to its sluggish diffusion rate in the Ni solid solution.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.3
• /
• pp.448-457
• /
• 2002

Heat treatment such as quenching of a high-temperature cylinder is being used on steel to produce high strength levels. Especially, the mist cooling with the high and uniform surface heat flux rate s expected to contribute for better products. The experimental mist cooling curve is produced for better understanding, and two distinct heat transfer regions are recognized from the cooling curve produced. It is shown that the liquid film evaporation dominated region follows the film boiling-dominated region as decreasing the temperature of test cylinder by mist flow. Based on the intuitive view from some previous investigations, a simplified model with some assumptions is introduced to explain the mist cooling curve, and it is shown that the estimation agrees well with our experimental data. In the meanwhile, it is known that the wetting temperature, at which surface heat flux rate is a maximum, increases with mass flow rate ratio of water to air ($\varkappa$ < 10). However, based on our experimental data, it is explained that there exists a critical mass flow rate ratio, at which the wetting temperature is maximum, in the range of 3 < $\varkappa$ < 130. Also, it is described that despite of the same value of $\varkappa$, the wetting temperature may increase with mist velocity.

• Korean Journal of Materials Research
• /
• v.12 no.12
• /
• pp.897-903
• /
• 2002

Morphological evolution and growth mechanism at the solid/liquid interface during solidification were investigated in the Ni-base superalloy GTD111M by directional soldification and quenching(DSQ) technique. The experiments were conducted by changing solidification rate(V) and thermal gradient(G) which are major solidification process variables. High thermal gradient condition could be obtained by increasing the furnace temperature and closely attaching the heating and cooling zones in the Bridgeman type furnace. The dendritic/equiaxed transition was found in the G/V value lower than $0.05$\times$10{^3}^{\circ}C$s/$\textrm{mm}^2$, and the planar interface of the MC-${\gamma}$ eutectic was found under $17 $\times$ 10{^3}^{\circ}C$ s/$\textrm{mm}^2$. It was confirmed that the dendrite spacing depended on the cooling rate(GV), and the primary spacing was affected by the thermal gradient more than solidification rate. The dendrite lengths were decreased as increasing the thermal graditne, and the dendrite tip temperature was close to the liquidus temperature at $50 \mu\textrm{m}$/s.

• Journal of the Korean Society for Heat Treatment
• /
• v.36 no.3
• /
• pp.121-127
• /
• 2023

When high carbon steel is heated in an appropriate austenizing temperature range and subjected to austempering, the size and shape of lamellar structure can be controlled. The high carbon steel sheet having the pearlite structure has excellent elastic characteristics because it has strong restoring force when properly rolled, and is applied in a process known as patenting-process using lead bath. In the case of isothermal treatment using lead-medium, it is possible to quickly reach a uniform temperature due to high heat transfer characteristics, but it is difficult to replace it with process technology that requires treatment to remove harmfulness lead. In this study, we intend to develop fluidization technology using garnet powder to replace the lead medium. After heating the high-carbon steel, the cooling rate was changed by compressed air to the vicinity of the nose of the continuous cooling curve, and then maintained for 90 s and then exposed to room temperature. The microstructure of the treated specimens were analyzed and compared with the existing products treated with lead bath. The higher the flow rate of compressed air, the faster the cooling rate to the pearlite transformation temperature, so lamellar spacing decreases and the hardness tends to increase.

• Nuclear Engineering and Technology
• /
• v.24 no.3
• /
• pp.297-310
• /
• 1992

FLECHT SEASET unblocked forced reflood tests are assessed using Apollo version of RELAP5/MOD3 5M5. The main purpose of the study is to examine the code predictability under forced reflood conditions having different initial power levels and flooding rates. Among various test matrices, the assessment calculations are performed for the test numbers 31701 31302, 31203, 31805, 34524, 31021, 34006 and 35807 These have been selected because they have similar initial conditions but different initial peak rod powers or flooding rates. In addition, various sensitivity calculations are performed for test number 31203 on the improved models of RELAP5/MOD3. Those are for the effect of Counter Current Flow Limit (CCFL) option at the outlet junction of the test section, for the effect of grid modelling on the interfacial drag calculations as well as on the heat structure calculations, and for the effect of nodalization and the time step size. The results of sensitivity studies show that the improved models of RELAP5/MOD3 enhance the code predictability. The assessment results show that the RELAP5/MOD3 has a tendency to underpredict the turn around temperature and the turn around time. But RELAP5/MOD3 silghtly overpredicts the turn around temperature for high flooding rate. The results also show that the calculated quenching by RELAP5/MOD3 is delayed with the increase of the rod power or the decrease of the flooding rate.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.23 no.3
• /
• pp.163-168
• /
• 2021

The growth experiment under shading condition has been performed to understand the eco-physiological responses of crops to light in terms of photosynthesis. There are two types of shading: overall shading and partial shading. In this study, the chlorophyll fluorescence of soybean was observed under the overall shading of the box made by polyresin and the partial shading at agrivoltaic system. The overall shading condition during vegetative growth induced lower SPAD and Electron transport rate (ETR). These lower values recovered after removal of shading box. However, the Non-photochemical fluorescence quenching (NPQ) became lower under overall shading and higher under partial shading. Such increase in NPQ limited crop photosynthesis even though the ETR was almost same to the control without shading treatment. Under the condition of partial shading, the values of SP AD and ETR for soybean did not change. However, the NPQ was higher than control condition. This suggests that the crop photosynthesis under both types of shading would be decreased by different eco-physiological processes which are the lower ETR in overall shading and the higher NP Q in partial shading despite the reduced light under shading conditions.

• Korean Chemical Engineering Research
• /
• v.54 no.1
• /
• pp.57-63
• /
• 2016

Thermally induced phase separation (TIPS) and nonsolvent induced phase separation (NIPS) were simultaneously induced for the preparation of flat PVDF membranes. N-methyl-2-pyrrolidone (NMP) was used as a solvent and dibutyl-phthlate (DBP) was used as a diluent for PVDF. When PVDF was melt blended with NMP and DBP, crystallization temperature was lowered for TIPS and unstable region was expanded for NIPS. Ratio of solvent to diluent changed the phase separation mechanism to obtain the various membrane structures. Contact mode of dope solution with nonsolvent determined the dominant phase separation behavior. Since heat transfer rate was greater than mass transfer rate, surface structure was formed by NIPS and inner structure was by TIPS. Quenching temperature of dope solution also affected the phase separation mechanism and phase separation rate to result in the variation of structure.