• Progress in Superconductivity
• /
• 제12권1호
• /
• pp.27-31
• /
• 2010

A superconductor flywheel energy storage system (SFES) is an electro-mechanical battery which transforms electrical energy into mechanical energy for storage, and vice versa. Many aspects of the quasi-static behavior of flywheel rotors still need to be studied closely, and the rotors require a stable and highly efficient supporting system such as high temperature superconductor (HTS) bearings, which offer dynamic stability without the use of active control. Quasi-static properties of HTS bearings in the radial direction provide data to solve problems which may occur in a running system. Since stiffness in countering rotor vibration is the main parameter for designing an HTS bearing system, we investigated the quasi-static properties of the magnetic force between permanent magnets(PMs) and HTS bulks in the radial direction. We measured radial stiffness, and discovered that bearing stiffness varied greatly depending on the number of active HTS bulks. This is valuable data for predicting the change in stiffness during partial HTS bearing failure. The quasi-static test results are used for optimal design and performance prediction for the 100 kWh class superconductor bearing.

• Composites Research
• /
• 제24권1호
• /
• pp.1-9
• /
• 2011

본 논문에서는 복합재료 튜브를 이용한 고속 열차의 에너지 흡수장치에 대한 실험 및 수치 해석에 관한 연구를 수행하였다. 논문의 목적은 에너지 흡수장치에 대한 최적의 적층(lay-up) 형태를 알아내는 것으로, quasi static method를 이용한 네 가지 적층 형태에 대한 실험을 수행 하였다: $[0/45/90/-45]_4$, $[0]_{16}$, $[0/90]_8$, $[0/30/-30]_5$, 실험을 위해 초기 파괴 시작점을 생성하고, 일정 방향으로 진행되는 파괴를 만들기 위해 베벨 엣지(bevel edge)와 노치 엣지(notch edge)의 두 가지 트리거링 방법을 이용하였다. 저속 충돌실험 결과 $[0/45/90/-45]_4$의 적층 형태가 다른 방법과 비교해서 가장 좋은 에너지 흡수 결과를 보여주였다. 수치해석을 위해 LS-DYNA 프로그램의 변수 분석(parametric analysis)을 통해 가장 적합한 복합재료의 quasi static 실험 시뮬레이션 방법 연구를 수행하였다. 움직이는 벽이 복합재 튜브에 저속 충돌하는 모델을 가정하여 해석을 수행하였으며, 실험값과 수치해석 결과의 비교를 통해 비슷한 경향을 보임을 확인 하였다. 특히 TFAIL과 mass scaling factor를 조절하며 수행하는 변수 분석은 LS-DYNA에서 복합재 튜브의 quasi static 실험을 시뮬레이션 하는 능력과 한계를 보여준다.

• 대한금속재료학회지
• /
• 제48권6호
• /
• pp.477-488
• /
• 2010

Zr-based amorphous alloy matrix composites reinforced with stainless steel (STS) and tantalum continuous fibers were fabricated without pores or defects by a liquid pressing process, and their quasi-static and dynamic deformation behaviors were investigated by using a universal testing machine and a Split Hopkinson pressure bar, respectively. The quasi-static compressive test results indicated that the fiberreinforced composites showed amaximum strength of about 1050~1300 MPa, and its strength maintained over 700 MPa until reaching astrain of 40%. Under dynamic loading, the maximum stresses of the composites were considerably higher than those under quasi-static loading because of the strain-rate hardening effect, whereas the fracture strains were considerably lower than those under quasi-static loading because of the decreased resistance to fracture. The STS-fiber-reinforced composite showed a greater compressive strength and ductility under dynamic loading than the tantalum-fiber-reinforced composite because of the excellent resistance to fracture of STS fibers.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 봄 학술발표회 논문집
• /
• pp.941-946
• /
• 2002

Short reinforced concrete bridge piers are particularly susceptible to shear failure as a consequence of the high shear/moment ratio and conservatism in the flexural strength design of existing RC bridge pier, which were constructed before 1992. In addition, shear failure is brittle and involves rapid strength degradation. Inelastic shear deformation is thus unsuitable for ductile seismic response. It is, however, believed that there are not many experimental research works for shear failure of the existing RC bridge pier in Korean peninsula subjected to earthquake motions. The object of this research is to evaluate the seismic performance of existing circular RC bridge piers by the quasi-static test. Existing RC bridge piers were moderate seismically designed in accordance with the conventional provisions of Korea Highway Design Specification. This study has been performed to verify the effect of aspect ratio (column height-diameter ratio). Quasi-static test has been done to investigate the physical seismic performance of RC bridge piers, such as lateral force-displacement hysteric curve, envelope curve etc.

• Journal of Mechanical Science and Technology
• /
• 제18권6호
• /
• pp.924-932
• /
• 2004

In this study, the axial collapse tests were performed under either static (or quasi-static) or impact loads with several collapse velocities based on the expectation that para-closed sections of the front-end side members (spot welded hat and double hat shaped section members) would show quite different collapse characteristics from those for seamless section. The test results showed that both of the hat and double hat shaped section members failed in the stable sequential collapse mode in the static or quasi-static collapse tests, while the double hat shaped section members underwent the unstable collapse mode especially when the impact velocity is high. The mean collapse loads in the hat shaped section members increase with collapse velocity for all the cases of the static, quasi-static, and impact collapse tests. In the double hat shaped section members, however, the mean collapse loads decrease with increase in collapse velocity in the impact tests.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 추계 학술발표회 제17권2호
• /
• pp.299-302
• /
• 2005

This study deals with the quasi-static tests on steel reinforced concrete composite columns with single embedded steel or multiple members. For the design of bridge piers, the composite section needs to have low steel ratio for cost savings because the dimension of the pier section is usually large. There is lack of design guidelines for these composite columns with low steel ratio, but the design provisions for the normal reinforced concrete column can be used for the design because of the low steel ratio. It is necessary to provide the design provisions in terms of the strength limit state and seismic performance by the detail requirements on the longitudinal steel and the transverse steel. The test parameters in this study were determined considering the current design provisions on RC columns. Through the quasi-static tests, the seismic performance of the composite columns were discussed.

• Structural Engineering and Mechanics
• /
• 제23권2호
• /
• pp.129-145
• /
• 2006

This paper provides an insight into the response of non-seismic reinforced concrete (RC) building frames to excitations of different frequencies through experimental investigation. The results of cyclic loading tests of six full-scale RC beam-column sub-assemblies are presented. The tested specimens did not have any transverse reinforcement inside the joint core, and they were subjected to quasi-static and dynamic loading with frequencies as high as 20 Hz. Some important differences between the cyclic responses of non-seismic and ductile RC frames are highlighted. The effect of excitation frequency on the behavior of non-seismic joints is also discussed. In the quasi-static tests, shear deformation of the joint panel accounted for more than 50% of the applied story drift. The test results also showed that higher-frequency excitations are less detrimental than quasi-static cyclic loads, and non-seismic frames can withstand a higher load and a larger deformation when they are applied faster.

• 항공우주시스템공학회지
• /
• 제4권3호
• /
• pp.1-5
• /
• 2010

Understanding the crushing behaviour of aluminum honeycombs under dynamic loading is useful for crash simulations of vehicles and for design of impacting energy absorbers. In the study of honeycomb crushing under quasi-static, dynamic loading, the most important parameter is crush strength. Crush strength is indicated to energy absorption characteristic of aluminum honeycomb. In this study, Using Finite Element Analysis carried out crush strength of hexagonal aluminum honeycomb then the results was compared with Quasi-static test. Consequently, Crush strength is different in quasi-static loading and dynamic loading about 16%.

• 소성∙가공
• /
• 제33권2호
• /
• pp.87-95
• /
• 2024

The current study aims to prove that high-speed forming has better formability than conventional low-speed forming. Experimentally, the quasi-static forming limit diagram was obtained by Nakajima test, and the dynamic forming limit diagram was measured by electrohydraulic forming. For the experiments, the LS-DYNA was used to create the optimal specimen for electrohydraulic forming. The strain measurement was performed using the ARGUS, and comparison of the forming limit diagrams confirmed that EHF showed better formability than quasi-static forming. Theoretically, the Marciniak-Kuczynski model was used to calculate the theoretical forming limit. Swift hardening function and Cowper Symonds model were applied to predict the forming limits in quasi-static and dynamic status numerically.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 가을 학술발표회 논문집
• /
• pp.965-970
• /
• 2001

The object of this research is to evaluate the seismic performance of existing RC bridge piers that were constructed before the adoption of the seismic design provision of Korea Bridge Design Specification in 1992. In this research, adopted test parameters were limited ductile design or non-seismic design, aspect ratio, confinement steel type, loading pattern, lap-spliced ratio for longitudinal reinforcement. This study has been performed to verify the effect of test parameter by quasi-static test. Quasi-static test has been done to investigate the physical seismic performance of RC bridge piers, such as lateral force-displacement hysteretic curve, envelope curve etc. It has been observed that seismic performance of lap-spliced test specimen, non-seismically designed specimens, was significantly reduced.