• Journal of the Earthquake Engineering Society of Korea
• /
• v.10 no.1 s.47
• /
• pp.41-49
• /
• 2006

Through the 1982 Urahawa-ohi and the 1995 Kobe earthquakes, a number of bridge columns were observed to develop a flexural-shear failure due to the bond slip as a consequence of premature termination of the column longitudinal reinforcement. Because the seismic behavior of RC bridge piers is largely dependent on the performance of the plastic hinge legion of RC bridge piers, it is desirable that the seismic capacity of RC bridge pier is to evaluate as a curvature ductility. The provision for the lap splice of longitudinal steel was not specified in KHBDS(Korea Highway Bridge Design Specification) before the implementation of 1992 seismic design code, but the lap splice of not more than 50%, longitudinal reinforcement was newly allowed in the 2005 version of the KHBDS. The objective of this research is to investigate the distribution and ductility of the curvature of RC bridge column with the lap splice of longitudinal reinforcement in the plastic hinge legion. Six (6) specimens were made in 600 mm diameter with an aspect ratio of 2.5 or 3.5. These piers were cyclically subjected to the quasi-static loads with the uniform axial load of $P=0.1f_{ck}A_g$. According to the slip failure of longitudinal steels of the lap spliced specimen by cyclic loads, the curvatures of the lower and upper parts of the lap spliced region were bigger and smaller than the corresponding paris of the specimen without a lap splice, respectively. Therefore, the damage of the lap spliced test column was concentrated almost on the lower part of the lap spliced region, that appeared io be failed in flexure.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.19 no.5
• /
• pp.56-66
• /
• 2015

This study aims at developing a new seismic resistant method by using precast concrete wall panels for existing low-rise, reinforced concrete beam-column buildings such as school buildings. Three quasi-static hysteresis loading tests were performed on one unreinforced beam-column specimen and two reinforced specimens with U-type precast wall panels. Seismic resistant test of anchored and welded steel plate connections manifested an average of 2.8 times increase in the maximum loading (average 591.8 kN) in comparison to unreinforced beam-column specimen. The maximum drift ratios were also shown between 1.4% and 2.7%. An analytical study was performed while assuming the RC column on the right side and the vertical element of the reinforced PC panel to behave in completely composite manner and the RC column on the left side and PC panel to behave in completely non-composite manner when loading was exerted from upper right end of RC frame of specimen to its left side. It was found with the assumptions that the overall flexural behavior in principle agreed with the experimental result.

• Journal of Korean Academy of Nursing
• /
• v.42 no.6
• /
• pp.843-852
• /
• 2012

Purpose: In this study a recreational combination gymnastics program was provided for women 75 years of age or older and the effects on physical fitness (grip strength, static balance, ability to do complex movement), depression, cognitive function and quality of life were examined. Methods: A quasi-experimental study employing a nonequivalent control group, pre-post design was conducted. Participants included 53 women elders whose cognitive function was within the normal range. The women were assigned to an experimental group (27) or a control group (26). The intervention was conducted twice a week for a period of 12 weeks. Chi-square test, t-test, paired t-test, Wilcoxon rank sum test and Wilcoxon signed rank test were used for data analysis. Results: Following completion of the program, left grip strength (t=2.17, p=.035), right grip strength (t=2.04, p=.046), static balance (t=-2.18, p=.030), depression (z=-2.88, p=.004), cognitive function (t=3.96, p<.001), and quality of life (t=-3.19, p=.002) were significantly better in the experimental group. Conclusion: Findings from this study indicate that recreational combination gymnastics programs are effective in enhancing physical fitness, cognitive function, and quality of life and in decreasing depression for female elders and could therefore be regarded as positive programs for promotion of physical and mental health for older women.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.12C
• /
• pp.1006-1013
• /
• 2008

CZZ (Concatenated Zigzag) Code is a class of fast encodable LDPC codes. In the case that LDPC codes including CZZ codes have short length, short cycles seriously affect the code performance. In this paper, we construct CZZ codes using various degree-2 polynomial interleavers which eliminate cycles of length 4 and through simulation, compare the performance of these CZZ codes and turbo codes in many different fading channels. Especially, quasi-static fading channel, block fading channel, uncorrelated fading channel, and correlated fading channel are considered. Since CZZ codes show similar performance as turbo codes, they can be used in the next generation wireless communication systems.

• Journal of Aerospace System Engineering
• /
• v.12 no.3
• /
• pp.26-37
• /
• 2018

The Korea Aerospace Research Institute has developed a 6U HiREV Nano-satellite for the observation of the earth using high resolution videos and images. Since the 6U Nano-satellite is bulky compared to the 1U/3U Nano-satellite, the first natural frequency is relatively low. Large equivalent stress and total deformation, due to structural load, can be generated. In this paper, the design of the 6U HiREV Nano-satellite is described and structure analysis, such as acceleration load analysis, modal analysis, and random vibration analysis are carried out. It is proven that the structural design of the 6U HiREV is stable. These results will be useful as reference materials for the development of additional 6U Nano-satellites, which will be applied to various future missions in KOREA.

• Journal of the Korean Society for Railway
• /
• v.13 no.2
• /
• pp.147-151
• /
• 2010

Since the kinetic energy is dissipated through plastic deformation energy generated in expanding process of the tube by a die. In order to successfully absorb the kinetic energy there should be no buckling in the expansion tube during expanding process. The buckling instability of the expansion tubes is affected by the initial boundary conditions, tube thickness and length. In this study, the effects of the tube thickness except length and initial boundary condition on the buckling instability are studied using a finite element method. In addition, Analysis procedure for nonlinear post-buckling analysis of expansion tube is established. There are three kinds of finite element analysis procedures for buckling analysis of expansion tube, quasi-static analysis, linear buckling analysis and nonlinear post-buckling analysis. The effect of the geometry imperfections defined as linear superimposition of buckling modes is considered in the nonlinear post-buckling analysis. The results of finite element analysis indicate that the buckling load increase with increase of thickness of tube and geometry imperfection. Finial buckling shapes are changed with respect to the geometry imperfection.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.19 no.1
• /
• pp.29-36
• /
• 2015

Base isolation is considered as a seismic protective system in the design of next generation Nuclear Power Plants (NPPs). If seismic isolation devices are installed in nuclear power plants then the safety under a seismic load of the power plant may be improved. However, with respect to some equipment, seismic risk may increase because displacement may become greater than before the installation of a seismic isolation device. Therefore, it is estimated to be necessary to select equipment in which the seismic risk increases due to an increase in the displacement by the installation of a seismic isolation device, and to perform research on the seismic performance of each piece of equipment. In this study, modified NRC-BNL benchmark models were used for seismic analysis. The numerical models include representations of isolation devices. In order to validate the numerical piping system model and to define the failure mode, a quasi-static loading test was conducted on the piping components before the analysis procedures. The fragility analysis was performed by using the results of the inelastic seismic response analysis. Inelastic seismic response analysis was carried out by using the shell finite element model of a piping system considering internal pressure. The implicit method was used for the direct integration time history analysis. In addition, the collapse load point was used for the failure mode for the fragility analysis.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.9
• /
• pp.195-202
• /
• 1999

The kinematic and complicance characteristics of torsion beam axle is structurally related to the location and section profile of torsion beam and the span from body mounting point to wheel center. This paper presents the effect of section properties in torsion beam on the structural characteristics and roll behavior of suspension. The structural characteristics is on the maximum stress on the welding area of torsion beam and the roll behavior is on roll steer and roll-camber of suspension which are important for controllability and stability in cornering. Four factors are used for the section design of torsion beam, which are thickness , midline length, are inner radius, and sector half angle . Through the structural and quasi-static analysis made for six torsion beam axle models, it can be noticed that roll steer and the structural durability of suspension are closely related to warping constant and shear center in section properties of torsion beam.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.925-934
• /
• 2005

The dynamic response due to the unbalance and crack and the quasi-static response due to gravity are analytically derived based on the complex transfer matrix. The additional slope is expressed as function of the bending moment at crack position based on the fracture mechanics concept, and inversely the bending moment is expressed as function of the additional slope at the crack position. At each angle step during the shaft revolution, the additional slope and bending moment are calculated by an iterative method. The transient behavior is considered by introducing Fourier series expansion concept for the additional slope. Simulation is carried out for a simple rotor similar to those available in the literature and comparison of the basic crack behavior is shown. Using the additional slope, the cracked rotor behavior is explained with the crack depth increased: the magnitude of the additional slope increases and the closed crack duration during a revolution decreases as the crack depth increases. The direction of unbalance is also shown as a factor to affect the crack breathing. Whirl orbits are shown near the sub-critical speed ranges of the rotor.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.12 s.177
• /
• pp.156-162
• /
• 2005

In this paper, we study the mechanism of lead deformation by numerically simulating the stamping process by means of a commercial finite element code. It is very important to analyze effects that the lead shape makes on the lead deformation, because the lead shape is often modified in order to minimize the deformation or to increase the buckling critical load of the punch. Therefore the stamping process, first, numerically simulated by considering as a quasi-static problem. Second, the effect on the lead deformation due to the lead shape variation, a linear lead geometry and a bent lead, was numerically analyzed and discussed. Finally, the punching order was optimized fur multi-lead generating stamping process. The results show that the bent lead is little bit more shifted than the linear lead after the punching process. But the bent lead is vertically less deformed than the linear lead. The punching order to successively generate the lead is good to keep the lead space uniform. The results will be very effectively applied for the design of the blanking or punching dies in industry.