• Journal of the Semiconductor & Display Technology
• /
• v.22 no.1
• /
• pp.78-82
• /
• 2023

Metal oxide semiconductor (MOS) adapting spray-pyrolysis deposition technique has drawn large attention based on their high quality of intrinsic and electrical properties in addition to simple and low-cost processibility. To fully utilize the merits of MOS field-effect transistors (FETs) , transparency, it is important to understand the instability behaviors of FETs under illumination. Here, we studied the photo-induced properties of nc-ZnO/ZnO field-effect transistors (FETs) based on spray-pyrolysis under illumination which incorporating ZnO nanocrystalline nanoparticles into typical ZnO precursor. Our experiments reveal that nc-ZnO in active layer suppressed the light instabilities of FETs.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2003.04a
• /
• pp.173-175
• /
• 2003

At the low temperature of $950^{\circ}C$ the $\mu\textrm{m}$-sized whisker growth during the catalytic CVD of pyrolytic carbon from methane with $H_2$- and Ar-gas on quartz substrate with NiO powder was found in this work. In the preliminary study it was observed from pure methane pyrolysis without catalyst at the high temperature $1500~1700^{\circ}C$. If the growth whisker should be stopped at initial stage, about 20 min. of the methane pyrolysis, it would be nanosized whisker growth. The screw growth mechanism and unique mechanical properties of whisker for composites were also recognized. If the pyrolysis would be continued, we could found also spiral growth of whistlers with diameter of about 1, 5 mm. The large length of whisker was about 10 cm in 20 minute.

• 한국초전도학회:학술대회논문집
• /
• v.13
• /
• pp.77-77
• /
• 2003

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1995.11a
• /
• pp.84-84
• /
• 1995

• Environmental Engineering Research
• /
• v.7 no.4
• /
• pp.247-252
• /
• 2002

• Analytical Science and Technology
• /
• v.28 no.3
• /
• pp.221-227
• /
• 2015

Animal glue is a traditional material that was used widely as an adhesive in cultural artifacts, such as Buddhist paintings, dancheong (traditional multicolored paintwork on wooden buildings), mother-of-pearl inlay, and so on. Spectroscopic methods, such as infrared spectroscopy, have been used for the analysis of animal glue. However, such methods do not yield sufficient information about the constituents of the glue. Because pyrolysis/GC/MS analysis is able to estimate the components of a material through the examination of its pyrolyzed products, it is useful for the analysis of polymeric material. In this study, pyrolysis/GC/MS analysis was used to determine the chemical composition of animal glue. The appropriate conditions for analyzing animal glue were established by examining pyrolysis temperature, quantity of the sample, and the repeatability of the method. Some products of pyrolysis were identified. We also analyzed commercial gelatin and animal glue using the established method and found almost no differences in chromatograms among the samples. The results will be used as supporting data to confirm the use of animal glue in cultural artifacts and to replace traditional animal glue by commercial gelatin.

• Fire Science and Engineering
• /
• v.31 no.3
• /
• pp.41-48
• /
• 2017

In order to investigate the influence of changes in the thermal properties of solid combustibles on thermal decomposition, a series of solid pyrolysis experiments were performed using a cone calorimeter specified in KS F ISO 5660-1. In the present study, Poly Methyl Methacrylate (PMMA) which does not produce Char during pyrolysis process was used as solid fuel. Results obtained from cone calorimeter experiments were compared to ones obtained from numerical analysis of Fire Dynamics Simulator (FDS) 1D pyrolysis model adopted with thermal properties of solid fuel as input parameters. Comparisons between experimentally calculated and model-predicted mass loss rate were then made to elucidate the effect of changes in the thermal properties on pyrolysis of PMMA.

• Journal of the Korean Applied Science and Technology
• /
• v.32 no.2
• /
• pp.281-289
• /
• 2015

This study investigated the conversion of oil products from polypropylene by using dispersed Co and Mo catalyst on reaction time and concentration change for knowledging liquefation characteristics at low-temperature (425, 450 and $475^{\circ}C$) pyrolysis in a batch reactor. The reaction time was set in 20~80 minutes and the oil products formed during pyrolysis were classfied into gas, gasoline, kero, diesel and heavy oil according to the domestic specification of petroleum products. The pyrolysis conversion rate was showed as Mo catalyst > Co catalyst > Thermal in all reaction time at reaction temperature $450^{\circ}C$. The conversion rate and yields of the pyrolysis products were the most height when Co and Mo Catalyst ratio was 50:50.

• Korean Journal of Materials Research
• /
• v.19 no.11
• /
• pp.581-587
• /
• 2009

Fe powders with elongated and aggregated structure as heat pellet material for thermal battery applications were prepared by spray pyrolysis under various preparation conditions. The precursor powders with spherical shapes and hollow morphologies turned into Fe powders after reduction at a temperature of 615$^{\circ}C$ under 20% $H_2$/Ar gas. The powders had pure Fe crystal structures irrespective of the preparation conditions of the precursor powders in the spray pyrolysis. The morphologies and mean sizes of the Fe powders are affected by the preparation conditions of the precursor powders in the spray pyrolysis. Therefore, the ignition sensitivities and the burn rates of the heat pellets formed from the Fe powders prepared by spray pyrolysis are affected by the preparations of the precursor powders. The Fe powders prepared under the optimum preparation conditions have a BET surface area of 2.9 $m^2g^1$. The heat pellets prepared from the Fe powders with elongated and aggregated structure have a good ignition sensitivity of 1.1W and a high burn rate of 18 $cms^1$.

• Journal of the Korean Society of Tobacco Science
• /
• v.30 no.2
• /
• pp.94-102
• /
• 2008

In this paper, we describe our study on the characterization of tobacco leaves by their pyrolysis patterns. Two kinds of tobacco leaves were pyrolyzed and analyzed by Double-Shot Pyrolysis-Gas Chromatography/Mass Spectroscopy (Py-GC/MS) methods. Three grades of Korean flue-cured tobacco leafsuch as B1O, AB3O, CD3L and burley tobacco leaves such as B1T, AB3T, CD3W were pyrolyzed with six discrete but stepwise heating temperature ranges, those are from 100$^{\circ}C$ to 150$^{\circ}C$, 150$^{\circ}C$ to 200$^{\circ}C$, 200$^{\circ}C$ to 250$^{\circ}C$, 250$^{\circ}C$ to 300$^{\circ}C$, 300$^{\circ}C$ to 350$^{\circ}C$ and finally from 350$^{\circ}C$ to 400$^{\circ}C$. Using the resultant 52 pyrolytic components identified in the programs as components, principal component analysis (PCA) showed statistical classification between flue-cured and burley tobacco lamina. Among six pyrolysis temperature ranges, the best discrimination was achieved at the temperature range from 250$^{\circ}C$ to 300$^{\circ}C$ and from 300$^{\circ}C$ to 350$^{\circ}C$.