• Steel and Composite Structures
• /
• 제36권1호
• /
• pp.103-118
• /
• 2020

The static behavior of grouped large-headed studs (d = 30 mm) embedded in ultra-high performance concrete (UHPC) was investigated by conducting push-out tests and numerical analysis. In the push-out test, no splitting cracks were found in the UHPC slab, and the shank failure control the shear capacity, indicating the large-headed stud matches well with the mechanical properties of UHPC. Besides, it is found that the shear resistance of the stud embedded in UHPC is 11.4% higher than that embedded in normal strength concrete, indicating that the shear resistance was improved. Regarding the numerical analysis, the parametric study was conducted to investigate the influence of the concrete strength, aspect ratio of stud, stud diameter, and the spacing of stud in the direction of shear force on the shear performance of the large-headed stud. It is found that the stud diameter and stud spacing have an obvious influence on the shear resistance. Based on the test and numerical analysis results, a formula was established to predict the load-slip relationship. The comparison indicates that the predicted results agree well with the test results. To accurately predict the shear resistance of the stud embedded in UHPC, a design equation for shear strength is proposed. The ratio of the calculation results to the test results is 0.99.

• 대한토목학회논문집
• /
• 제26권1A호
• /
• pp.91-97
• /
• 2006

본 연구에서는 강-콘크리트 합성 바닥판용 유공판재형 전단연결재의 전단성능을 평가하기 위한 전단실험을 수행하고 그 실험결과를 고찰하였다. 전단 실험체는 절곡된 강판, 유공판재형 전단연결재, 철근, 콘크리트로 구성되었으며, 절곡된 강판과 콘크리트 사이에 작용하는 수평전단력에 저항할 수 있도록 다수의 구멍이 가공된 유공판재형 전단연결재가 적용되었다. 실험체설계에 적용된 변수는 구멍의 간격과 위치, 구멍관통 철근의 유무이며, 총 12개의 실험체를 제작하여 전단실험을 수행하였다. 제한적 범위 내에서 수행한 실험결과에 따르면 유공판재형 전단연결재가 강-콘크리트 합성 바닥판에 효과적으로 사용될 수 있을 것으로 판단된다.

• 한국강구조학회 논문집
• /
• 제27권5호
• /
• pp.483-491
• /
• 2015

앵글을 전단연결재로 사용한 시공개선형 합성보(BESTOBEAM)의 전단연결재 길이에 따른 전단 내력을 실험적으로 평가하고 전단내력 설계식을 제안하였다. Eurocode 4의 경우와 달리 BESTOBEAM의 전단연결재는 등분포 하중을 받는 보의 거동과 유사하며 그 순경간(BESTO Width)에 따라 전단 내력이 달라진다. BESTO Width와 콘크리트의 강도에 따른 전단 내력을 Push-out 실험을 통해 측정한 결과 BESTO Width가 길어질수록 내력이 감소하고 연성능력은 증가하는 경향을 보였다. 실험결과를 반영하여 Eurocode 4의 설계식을 수정하여 새로운 설계식을 제안하였다. 제안된 설계식을 통해 예측된 전단연결재의 강도는 10% 오차 범위 이내로 잘 맞는 것을 확인할 수 있었다. 따라서 앵글을 전단연결재로 사용한 BESTOBEAM의 전단 강도 설계에 제안된 식을 사용할 수 있을 것으로 판단된다.

• 한국산학기술학회논문지
• /
• 제14권10호
• /
• pp.5290-5298
• /
• 2013

본 논문에서는 프리캐스트 방식으로 제작 가능한 격자형 강합성 바닥판의 이음부에 기계식 연결방식을 적용하고자 콘크리트 전단키와 고장력볼트로 구성되는 이음부에 대해 Push-out 시험으로 전단내력을 구하였으며, 이를 전단마찰 이론에 근거한 이론식 및 설계식과 비교함으로써 전단내력을 평가하였다. 분석결과에 따르면, 이음부 접합면을 에폭시로 부착한 경우가 전단키를 강판으로 보강한 경우 보다 약 10% 정도 더 큰 전단내력을 갖는 것으로 나타났으나, 실험체간 전단내력의 편차는 전단키를 강판으로 보강한 경우가 더 작게 나타났다. 실험결과를 계산식 및 설계식과 비교한 결과, 기존 설계식으로 안전하게 설계될 수 있음을 알 수 있었다. 그러나, ACI-318에 의할 경우 이음부 전단내력이 과소평가되기 때문에 LRFD에서 제시된 설계식의 적용이 더 적당한 것으로 분석되었다.

• Steel and Composite Structures
• /
• 제42권4호
• /
• pp.477-487
• /
• 2022

The shear stiffness of headed-stud shear connectors has no unified definition due to the nonlinear characteristics of its load-slip relationship. A unified framework was firstly adopted to develop a general expression of shear load-slip equation for headed-stud shear connectors varying in a large parameter range based on both force and energy balance. The pre- and post-yield shear stiffness were then determined through bilinear idealization of proposed shear load-slip equation. An updated and carefully selected push-out test database of 157 stud shear connectors, conducting on studs 13~30mm in diameter and on concretes 30~180 MPa in cubic compressive strength, was used for model regression and sensitivity analysis of shear stiffness. An empirical calculation model was also established for the stud shear stiffness. Compared with the previous models through statistical analysis, the proposed model demonstrates a better performance to predict the shear load-slip response and stiffness of the stud shear connectors.

• Structural Engineering and Mechanics
• /
• 제80권5호
• /
• pp.595-608
• /
• 2021

To investigate the mechanical behavior of large stud shear connector embedded in hybrid fiber-reinforced concrete (HFRC), a refined 3D nonlinear finite element (FE) model incorporating the constitutive model of HFRC was developed using ANSYS. Firstly, the test results conducted by the authors (He et al. 2017) were used to validate FE model of push out tests. Secondly, a total of 27 specimens were analyzed with various parameters including fiber volume fractions of HFRC, diameter of studs and HFRC strength. Finally, an empirical equation considering the contribution of steel fiber (SF) and polypropylene fiber (PF) was recommended to estimate the ultimate capacity of large stud shear connector embedded in HFRC.

• Steel and Composite Structures
• /
• 제33권6호
• /
• pp.823-836
• /
• 2019

Spiral welded tubes (SWTs) are fabricated by helically bending a steel plate and welding the resulting abutting edges. The cost-effectiveness of concrete-filled steel tube (CFST) columns can be enhanced by utilising such SWTs rather than the more conventional longitudinal seam welded tubes. Even though the steel-concrete interface bond strength of such concrete-filled spiral-welded steel tubes (CF-SWSTs) is an important consideration in relation to ensuring composite behaviour of such elements, especially at connections, it has not been investigated in detail to date. CF-SWSTs warrant separate consideration of their bond behaviour to CFSTs of other tube types due to the distinct weld seam geometry and fabrication induced surface imperfection patterns of SWTs. To address this research gap, axial push-out tests on forty CF-SWSTs were carried out where the effects of tube material, outside diameter (D), outside diameter to wall thickness (D/t), length of the steel-concrete interface (L) and concrete strength grade (f'_c) were investigated. D, D/t and L/D values in the range 102-305 mm, 51-152.5 and 1.8-5.9 were considered while two nominal concrete grades, 20 MPa and 50 MPa, were used for the tests. The test results showed that the push-out bond strengths of CF-SWSTs of both mild-steel and stainless-steel were either similar to or greater than those of comparable CFSTs of other tube types. The bond strengths obtained experimentally for the tested CF-SWSTs, irrespective of the tube material type, were found to be well predicted by the guidelines contained in AISC-360.

• 한국강구조학회 논문집
• /
• 제25권1호
• /
• pp.93-102
• /
• 2013

본 연구에서는 철근콘크리트 벽과 강판 콘크리트 벽이 서로 수직면의 이질접합 형태로 만나는 벽의 면외 휨 거동 특성을 검토하기 위하여, L형 실험체를 제작하고 휨 실험을 수행하였다. 실험 시, 실험체의 동적특성을 확인하기 위하여 Push 및 Pull 하중을 반복하는 싸이클 하중을 구현하고자 하였다. Push 하중에 의한 실험 결과, 실험체의 공칭강도를 초과하는 휨 성능을 발휘하였으며, 이에 따라 설계에 적용된 수직철근의 미겹침 이음길이의 타당성을 확인할 수 있었다. 한편, Pull 하중 가력 시에는 수직철근이 최대 내력을 발휘하기 전에 접합부 콘크리트에서 전단 파괴 거동이 나타나, 이에 대한 보강이 필요함을 확인하였다.

• Steel and Composite Structures
• /
• 제19권1호
• /
• pp.21-41
• /
• 2015

Push-out tests have been conducted on 18 rectangular concrete-filled steel tubular (CFST) columns with the aim of studying the bond behaviour between the steel tube and the concrete infill. The obtained load-slip response and the distribution of the interface bond stress along the member length and around the cross-section for various load levels, as derived from measured axial strain gradients in the steel tube, are reported. Concrete compressive strength, interface length, cross-sectional dimensions and different interface conditions were varied to assess their effect on the ultimate bond stress. The test results indicate that lubricating the steel-concrete interface always had a significant adverse effect on the interface bond strength. Among the other variables considered, concrete compressive strength and cross-section size were found to have a pronounced effect on the bond strength of non-lubricated specimens for the range of cross-section geometries considered, which is not reflected in the European structural design code for composite structures, EN 1994-1-1 (2004). Finally, based on nonlinear regression of the test data generated in the present study, supplemented by additional data obtained from the literature, an empirical equation has been proposed for predicting the average ultimate bond strength for SHS and RHS filled with normal strength concrete.

• The Journal of Advanced Prosthodontics
• /
• 제5권3호
• /
• pp.305-311
• /
• 2013

PURPOSE. Over the past years, the adhesion of fiber posts luted with simplified adhesive systems has been a matter of great interest. The aim of this study was to assess the post retentive potential of a self-adhesive resin cement using different adhesive systems to compare the push-out bond strengths of fiber posts. MATERIALS AND METHODS. The post spaces of 56 mandibular premolar roots were prepared and divided into 4 experimental groups and further divided into 2 subgroups according to testing time (n=7). The fiber posts (Rely X Fiber Post) were luted with a self-adhesive resin cement (RelyX Unicem) and one of the following adhesive systems: no adhesive, a total-etch adhesive resin (Single Bond), a two-step self-etch adhesive resin (Clearfil SE Bond) and a one-step self-etch adhesive resin (Clearfil S3 Bond). Each root was cut horizontally, and 1.5 mm thick six root segments were prepared. Push-out tests were performed after one week or three months (0.5 mm/min). Statistical analysis were performed with three-way ANOVA (${\alpha}$=.05). RESULTS. Cervical root segments showed higher bond strength values than middle segments. Adhesive application increased the bond strength. For one week group, the total-etch adhesive resin Single Bond showed higher bond strength than the self-adhesive resin cement RelyX Unicem applied without adhesive resin at middle region. For 3 months group, the two-step self-etch adhesive resin Clearfil SE Bond showed the highest bond strength for both regions. Regarding the time considered, Clearfil SE Bond 3 months group showed higher bond strength values than one week group. CONCLUSION. Using the adhesive resins in combination with the self-adhesive resin cement improves the bond strengths. The bond strength values of two-step self-etch adhesive resin Clearfil SE Bond improved as time passes.