• Korean Chemical Engineering Research
• /
• v.46 no.6
• /
• pp.1095-1099
• /
• 2008

In this study, we investigated that hydrate formation and phase behavior of the $THF+H_2$ binary clathrate hydrates. In order to confirm the binary clathrate hydrate formation we employed the Raman and NMR spectroscopies that are known to be quite powerful tools, particularly for examining the cage occupancy pattern of guest molecules. In addition, we traced the P-T profiles from clathrate hydrate formation and dissociation process, which made it possible for the resulting phase equilibrium boundary to be clearly established. In the binary clathrate hydrate matrix we further identified that the relatively large THF molecules can only occupy the large $5^{12}6^4$ cavities, while the small $H_2$ molecules are entrapped in the empty $5^{12}$ cavities in structure-II, making the hydrate to be stable above 273 K even at relatively low pressure condition. Considering that pure $H_2$ hydrate can be produced at the extreme pressures higher that 1,000 bar, we can conclude that the water-soluble second guest inclusion induces $H_2$ storage and transportation to be readily achievable under much milder conditions.

• Food Science and Preservation
• /
• v.23 no.6
• /
• pp.906-912
• /
• 2016

${\beta}$-Glucan is a natural compound contained in cell walls of yeast or fungi, and cereal's fiber. It is also known to boost the immune system in human. Aureobasidium is a producer of water-soluble ${\beta}$-1,3/1,6-glucan. In this study, natural killer (NK) cell and macrophage activity were tested to investigate the effects of ${\beta}$-1,3/1,6-glucan isolated from A. pullulans on immune activity. Activation of NK cell was increased about 63-39% by the treatment of $10-200{\mu}g/mL$ ${\beta}$-1,3/1,6-glucan than control. Besides, only $10{\mu}g/mL$ of ${\beta}$-1,3/1,6-glucan was enough to boost activation of NK cell. Phagocytosis of macrophage was increased to 15~21% by the treatment of $10{\sim}200{\mu}g/mL$ of ${\beta}$-1,3/1,6-glucan than zymosan-treatment. In LP-BM5 proliferating inhibition test, relative mRNA level of LP-BM5 virus was decreased in ${\beta}$-1,3/1,6-glucan-treated cell about 36~74% than control. The decline of LP-BM5 mRNA level appeared to depend on the concentration of ${\beta}$-1,3/1,6-glucan. These results suggest that pure ${\beta}$-1,3/1,6-glucan from A. pullulans might be contributing to enhancement of immune activity through the activation of NK cell and phagocytosis of macrophage. Moreover, treatment of the ${\beta}$-1,3/1,6-glucan could increase the resistance to virus infection such as LP-BM5 through the restraining of the multiplication.

• Archives of Pharmacal Research
• /
• v.28 no.5
• /
• pp.604-611
• /
• 2005

Polyethylene glycol (PEG) 6000-based solid dispersions (SDs), by incorporating various pharmaceutical excipients or microemulsion systems, were prepared using a fusion method, t o compare the dissolution rates and bioavailabilities in rats. The amorphous structure of the drug in SDs was also characterized by powder X-ray diffractometry (XRD) and differential scanning calorimetry (DSC). The ketoconazole (KT), as an antifungal agent, was selected as a model drug. The dissolution rate of KT increased when solubilizing excipients were incorporated into the PEG-based SDs. When hydrophilic and lipophilic excipients were combined and incorporated into PEG-based SDs, a remarkable enhancement of the dissolution rate was observed. The PEG-based SDs, incorporating a self microemulsifying drug delivery system (SMEDDS) or microemulsion (ME), were also useful at improving the dissolution rate by forming a microemulsion or dispersible particles within the aqueous medium. However, due to the limited solubilization capacity, these PEG-based SDs showed dissolution rates, below 50% in this study, under sink conditions. The PEG-based SD, with no pharmaceutical excipients incorporated, increased the maximum plasma concentration (C$_{max}$) and area under the plasma concentration curve (AUC$_{0-6h}$) two-fold compared to the drug only. The bioavailability was more pronounced in the cases of solubilizing and microemulsifying PEG-based SDs. The thermograms of the PEG-based SDs showed the characteristic peak of the carrier matrix around 60$^{\circ}C$, without a drug peak, indicating that the drug had changed into an amorphous structure. The diffraction pattern of the pure drug showed the drug to be highly crystalline in nature, as indicated by numerous distinctive peaks. The lack of the numerous distinctive peaks of the drug in the PEG-based SDs demonstrated that a high concentration of the drug molecules was dissolved in the solid-state carrier matrix of the amorphous structure. The utilization of oils, fatty acid and surfactant, or their mixtures, in PEG-based SD could be a useful tool to enhance the dissolution and bioavailability of poorly water-soluble drugs by forming solubilizing and microemulsifying systems when exposed to gastrointestinal fluid.

• Membrane Journal
• /
• v.12 no.2
• /
• pp.75-89
• /
• 2002

The effect of addition of inorganic salts in polyethersulfone (PES) polymer solution on the membrane formation and ultrafiltartion performance was studied through the thermodynamic and kinetic properties of casting solution. To control the thermodynamic and kinetic properties of casting solution, various inorganic salts $[CaC1_2, LiCl, LiClO_4, ZnC1_2 $and Mg(ClO_4)_2]$ were added in the PES/NMP solution. Variation of membrane morphology and performance of the resulting membranes with change of the salt type and content added in tasting solution were discussed using viscosity, coagulation value, light transmittance measurement, overall membrane porosity, ultrafiltration experiment and cross-sectional SEM image. For all kind of inorganic salts, according as increase of the salt content in casting solution, viscosity is increased, coagulation value becomes lower, top layer thickness below the skin surface is increased, bovine serum albumin(BSA) rejection decreased and pure water flux is increased except $CaC1_2$ and LiCl. In case of $CaC1_2$ and LiCl, it is found that when the salt content is increased, the formation of macrovoids is suppressed and the precipitation rate becomes slow while instantaneous demixing of precipitation type is maintained. However, in case of $LiClO_4$ and $Mg(ClO_4)_2,$ it is found that precipitation rate becomes faster.

• Clean Technology
• /
• v.5 no.2
• /
• pp.25-35
• /
• 1999

Behavior of permeate flux decline was examined through the hollow fiber membrane in ultrafiltration system for Si colloidal solution. Flux decline with time was due to the growth of Si cake deposited on the membrane surface and the pore blocking by Si particles for the hollow fiber membrane. At the pseudo steady state of operation, the permeate flux of dead-end flow was 60 % to that of the cross flow. The ratio of permeate flux to the pure water flux, $J/J_w$, decreased with increasing the trans-membrane pressure, from 64.2 % for $0.5kg_f/cm^2$ to 45.7 % for $2.0kg_f/cm^2$. When the feed flow rate was 3 L/min, the pore blocking model was dominant at the initial period of filtration and was followed by the cake filtration model. And with increasing the feed flow rate from 1 L/min to 3 L/min, $R_c$ was $1.79{\times}10^{12}{\sim}2.34{\times}10^{12}m^{-1}$ which was the about 40 % decreased value to that of the 1 L/min while $R_p$ was not changed and was $1.71{\times}10^{12}m^{-1}$ approximately.

• Membrane Journal
• /
• v.26 no.3
• /
• pp.205-211
• /
• 2016

Performance of pyrophyllite-based ceramic membranes newly developed were investigated. Membrane fouling caused by microbial suspensions taken from a full-scaled MBR system at domestic wastewater treatment plant was observed at different airflow rate and distance between each membrane. For the pyrophyllite support, pore size was about $1.0{\mu}m$, but surface coating with $Al_2O_3$ solution decreased the pore size with the reduction of the pure water permeability. With the MLSS taken from the full-scaled MBR system (6 g/L), the fouling rate was decreased by increasing airflow rate under $20L/m^2{\cdot}hr$ of setpoint flux. However, the effectiveness of the airflow rate on the fouling control depends strongly upon the gap between each membrane. At fixed airflow rate, the fouling rate was decreased by increasing the gap between each pyrophyllite membrane. Nevertheless, further increasing the membrane distance from 3.5 to 5.4 cm resulted in higher fouling rate. Similar result was observed with the $Al_2O_3$ coated-pyrophyllite membrane. Nevertheless, the fouling rate was lower with the coated membrane than that observed with the uncoated pyrophyllite support. Regardless of surface coating, the suspended solids were removed almost completely and the surface coating on the pyrophyllite support improved organic rejection with PEG solution (MW : 8000 kDa) tested.

• Korean Journal of Materials Research
• /
• v.8 no.6
• /
• pp.513-519
• /
• 1998

Zr-Si binary alloys containing 0.01 to O.lwt.%Si were prepared to investigate the effect of Si on the corrosion behavior of Zr. Corrosion test was performed in pure water at 36$0^{\circ}C$ under a pressure of 2660psi for 100days. The alloys containing 0.01 wt. % and 0.05wt. %Si had the black and uniform oxide film and didn't show the transition of corrosion rate. However. the alloys containing O.lwt.%Si had white oxide film and showed the trasition of corrosion rate at 70 days corrosion test. The weight gain increased with the increasing Si content from 0.01 to 0.1 wt.%. The variation of Si contents had no effect on changing the oxide structure but had significant effect on the electrical resistivity of oxide. The electrical resistivity decreased with increasing Si content. The fraction of precipitates in the Zr-Si binary alloys. identified as tetragonal $Zr_{3}$Si increased with increasing Si content. The increase of the volume fraction of precipitates is thought to be responsible for the increase of weight gain due to short circuit effect of precipitate.

• Journal of the Korean Applied Science and Technology
• /
• v.16 no.1
• /
• pp.33-40
• /
• 1999

We used Cu as a representative of metals to be directly adsorbed on the bare Si surface and studied its removal DHF, DHF-$H_2O_2$ and BHF solution. It has been found that Cu ion in DHF adheres on every Si wafer surface that we used in our study (n, p, n+, p+) especially on the n+-Si surface. The DHF-$H_2O_2$ solution is found to be effective in removing metals featuring high electronegativity such as Cu from the p-Si and n-Si wafers. Even when the DHF-$H_2O_2$ solution has Cu ions at the concentration of 1ppm, the solution is found effective in cleaning the wafer. In the case the n+-Si and p+-Si wafers, however, their surfaces get contaminated with Cu When Cu ion of 10ppb remains in the DHF-$H_2O_2$ solution. When BHF is used, Cu in BHF is more likely to contaminate the n+-Si wafer. It is also revealed that the surfactant added to BHF improve wettability onto p-Si, n-Si and p+-Si wafer surface. This effect of the surfactant, however, is not observed on the n+-Si wafer and is increased when it is immersed in the DHF-$H_2O_2$ solution for 10min. The rate of the metallic contamination on the n+-Si wafer is found to be much higher than on the other Si wafers. In order to suppress the metallic contamination on every type of Si surface below 1010atoms/cm2, the metallic concentration in ultra pure water and high-purity DHF which is employed at the final stage of the cleaning process must be lowered below the part per trillion level. The DHF-$H_2O_2$ solution, however, degrades surface roughness on the substrate with the n+ and p+ surfaces. In order to remove metallic impurities on these surfaces, there is no choice at present but to use the $NH_4OH-H_2O_2-H_2O$ and $HCl-H_2O_2-H_2O$ cleaning.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.30 no.2
• /
• pp.167-172
• /
• 2004

In the human skin, vitamin C (L -ascorbic acid) that is well known as the activated materials has effects that is skin anti-aging and wrinkle repair by giving impetus to collagen biosynthesis and anti-oxidation, and that is the sun screen, a wound recovering, inhibition melanogenesis and so on. In spite of its effects, vitamin C has the defects of the skin stimulation and easily oxidized instability by water, air, heat and light. For solving their matters, many investigation is advanced and its results are synthesized the various vitamin C derivatives. And yet they have not solved the unstable property of vitamin C and were still insufficient for the comparing with the effect of the pure vitamin C itself. In this study, in order to prepare vitamin C derivative of being improved the stability and to apply vitamin C effect in the skin, we prepared new vitamin C derivative, phytosphingosine ascorbate, by using phytosphingosine, one of sphingolipids, which have a distinguished skin affinity. Phytosphingosine ascorbate can be prepared as the ionic bond between amine group (-NH$_2$) of phytosphingosine and hydroxy group (-OH) of vitamin C by way of the relatively simple reaction. So the structure and properties of the synthesized phytosphingosine ascorbate was confirmed the use of elemental analysis (C 58.3 : H 9.3 : N 2.8 : O 29.5), MALDI TOF-MS (Mw=492.58), Ultraviolet spectra (268.5nm), lH NMR, FT-IR spectra, thermal analysis (m.p=l54$^{\circ}C$), HPLC and so on. And we could confirm the anti-bacterial and anti-oxidation effects. Based on these results, we could confirm to prepare a new material that was expected of both effects of vitamin C and phytosphingosine and that is improved properties of vitamin C.

• Journal of the East Asian Society of Dietary Life
• /
• v.18 no.3
• /
• pp.353-360
• /
• 2008

This study evaluated the quality characteristics of dried noodles made of wheat flour supplemented with different concentrations of skate powder. Cooking quality, mechanical texture properties, gelatinization temperature and viscosity were measured, after which sensory evaluation was performed with prepared noodles. Water binding capacity, solubility and swelling power of the composite skate powder and wheat flours were higher than those of pure wheat flour. Gelatinization temperature of the composite skate powder and wheat flours increased, while initial, interim, and maximum-viscosity at $95^{\circ}C$, decreased, with increasing skate powder content. In relation to color values, increasing skate flour content led to decrease in L and b values and increase in a value. For the textural characteristics, the addition of skate powder increased hardness, springiness, chewiness and adhesiveness. Overall, noodles made with 3% skate powder were preferred compared to other samples.