• 한국정보통신학회논문지
• /
• 제12권3호
• /
• pp.517-526
• /
• 2008

본 논문에서는 자동차 계기판의 OLED 디스플레이 모듈용 One-chip DC-DC 변환기 회로를 제안하였다. 전하 펌핑 방식의 OLED 패널 구동전압 회로는 PWM(Pulse Width Modulation) 방식을 사용한 DC-DC 변환기 회로에 비해 소형화, 저가격 및 낮은 EMI 특성을 갖는다. 그리고 Bulk-potential 바이어싱 회로를 사용하므로 전하 펌핑 시 기생하는 PNP BJT에 의한 전하 손실을 방지하도록 하였고, 밴드갭 기준전압 발생기의 Start-up 회로에서 전류소모를 기존 BGR 회로에 비해 42% 줄였고 VDD의 링 발진기 회로에 로직전원인 VLP를 사용하여 링 발진기기 레이아웃 면적을 줄였다. 또한 OLED 구동전압인 VDD의 구동 전류는 OLED 패널에서 요구하는 40mA 이상이다. $0.25{\mu}m$ High-voltage 공정을 이용하여 테스트 칩을 제작 중에 있으며, 레이아웃 면적은$477{\mu}m{\times}653{\mu}m$이다.

• 대한의용생체공학회:학술대회논문집
• /
• 대한의용생체공학회 1996년도 춘계학술대회
• /
• pp.207-212
• /
• 1996

We developed pneumatic blood pump and its driving system as a pediatric ventricular assist device. The blood pump is diaphragm type system and its blood contacting area is coated with Bio-Span. The driving unit Is consists of dual pumps, valves for the reliable blood pumping and its controller uses 80C196(Intel) as a main processor. The acute animal experiment was performed with dogs and its body weight is about 20 kg. The maximum cardiac output is about 2.1 l/min and the pressure and flow curves showed reliable operation as assist device.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1824-1827
• /
• 2005

For application to micro fluid control systems such as ${\mu}TAS$ (Micro Total Analysis Systems) and DDS (Drug Delivery Systems), it is very significant to handle precise and minute flow rates with low pressure pulsation. In this study, a novel valveless piezoelectric pump using peristaltic motion with three disk type PZT actuators is presented. The newly devised pump with an effective size of $70mm{\times}60mm{\times}55mm$ has three actuator layers connected in series from inlet to outlet. The PZT actuator has a maximum displacement of 240 ${\mu}m$ and a maximum force of 1.6 N. When the driving voltage for PZT actuators is sequentially applied with a certain phase shift, the pumping is performed by peristaltic motion of liquid volume. The working fluid is shut off without the driving voltage. Three methods for sequential driving are proposed and experimentally investigated. First and second methods utilize an intermittent sinusoidal waveform with phase shift of $90{\circ}\;and\;120^{\circ}$, respectively. Third method uses a rectangular waveform with phase shift of $90^{\circ}$. A controller with multi-phase shifter is designed and fabricated. Then, frequency and voltage-flow rate characteristics and load pressure-flow rate characteristics are experimentally investigated to verify the validity of the developed pump.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.134-136
• /
• 2008

In recent years, the switched reluctance motor have been used many industrial application because of its cost advantage. SRM drivers are accomplished by switching the phase currents on and off synchronously with the rotor position which is fed back to the controller by position may deteriorate in harsh environments and increase the size and cost of the SRM drive system. This paper proposes a position sensorless method that is based on impressed pulse voltage using impressed at unenergised phases to estimate the rotor position. The current value by impressed pulse voltage compare with the threshold value. The rotor position can be estimated by observing the current value. Finally, simulation results compare with the sensor type SRM and confirm the proposed method to be useful.

• 진공이야기
• /
• 제4권1호
• /
• pp.16-23
• /
• 2017

Recently, KSTAR, Korea's superconducting fusion energy research and development device, has succeeded in driving the high performance plasma for 70 seconds for the first time in the world. Continuous plasma operation technology is an essential factor for commercialization of fusion energy power generation. Therefore, this achievement is expected to play a major role in the research of fusion technology required for future fusion power plants. In order to operate the KSTAR, the discharge process in which the neutral gas is turned into the plasma should be preceded in the start-up (breakdown) phase of tokamak operation. This process essentially involves the vacuum environment in the tokamak device. KSTAR has successfully operated a vacuum pumping system to achieve the target level of the vacuum environment through a high temperature baking operation, a discharge cleaning process and boronization.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.647-650
• /
• 2001

In case of bent axis type axial piston hydraulic pump or motor, hydrostatic bearing used to achieve the lubrication effect on the mechanical sliding contact areas between the following pairs ; piston shoe and swash plate, valve plate and cylinder block, piston and cylinder block, etc. In this research, we designed two pairs of spherical ball joint in witch connecting rod piston end. The one is not hydrostatic bearing, the other is designed with spherical hydrostatic bearing in point of view minimum pumping power loss. By varying supply pressure on the piston, we can know that it is possible to reduce the friction torque by using hydrostatic bearing designed one. Finally, by comparing the results of driving torque between the two models, it was verified that the spherical hydrostatic bearing is well designed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.185-187
• /
• 2008

This paper proposed design and development of a photo voltaic (PV) array fed induction motor drive. A drive system using a chopper circuit to track maximum power from the PV for different solar insolation and a current controlled voltage source inverter (CC-VSI) to optimally match the motor to PV characteristics is presented. The model equations governing interaction of torque and flux producing components of motor current with available solar power is developed for the operation of the system at optimum efficiency. Performance of the system is presented for different realistic operating conditions, which demonstrates its special features for applications such as solar water pumping system, solar vehicles and floor mills located in hilly and isolated areas.

• 대한기계학회논문집B
• /
• 제27권9호
• /
• pp.1256-1261
• /
• 2003

Since the viscous effect increases as the size of device decreases, viscous-driven micropump is a promising mechanism in microscale applications. In the present study, a dual-rotor type pump which contains two counter-rotating cylinders for improving performance characteristics is proposed. First, for flows in the single-rotor type pump, the present unstructured grid simulation method is validated by comparing its results to the previous results. Next, the performance of the dual-rotor type pump is evaluated by the parametric studies and is compared to that of the previous single-rotor type pump. The flow characteristics are qualitatively similar to those of single-rotor type pump. However, the performance of the micropump with tandem rotors is still better than that of previous pumping type, e.g. much larger flow rate, smaller driving region, higher efficiency, and wider operation range.

• 한국자동차공학회논문집
• /
• 제22권3호
• /
• pp.228-233
• /
• 2014

Reduction of the atmospheric pressure in high altitude affects brake booster system which was operated by the difference between the intake pressure and the atmospheric pressure. So, braking system can not stably perform due to decrease of brake boost pressure. In this study, effects of altitude change on engine intake pressure was analyzed by prediction model of engine intake pressure which was studied previously. And engine intake pressure was simulated by simulation model in various driving conditions and environmental conditions.

• 한국자동차공학회논문집
• /
• 제19권2호
• /
• pp.26-34
• /
• 2011

Hybrid powertrain systems have been developed to improve the fuel efficiency of internal combustion engines. In the case of a parallel hybrid powertrain system, an engine and a motor are directly coupled. Because of the hardware configuration of the parallel hybrid system, friction and the pumping losses of internal combustion engines always exists. Such losses are the primary factors that result in the deterioration of fuel efficiency in the parallel-type hybrid powertrain system. In particular, the engine operates as a power consumption device during the fuel-cut condition. In order to improve the fuel efficiency for the parallel-type hybrid system, cylinder deactivation (CDA) technology was developed. Cylinder deactivation technology can improve fuel efficiency by reducing pumping losses during the fuel-cut driving condition. In a CDA engine, there are two operating modes: a CDA mode and an SI mode according to the vehicle operating condition. However, during the mode change from CDA to SI, a serious fluctuation of the air-fuel ratio can occur without adequate control. In this study, an air-fuel ratio control algorithm during the mode transition from CDA to SI was proposed. The control algorithm was developed based on the mean value CDA engine model. Finally, the performance of the control algorithm was validated by various engine experiments.