• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.1
• /
• pp.223-228
• /
• 2017

In this paper, we are proposing an optimal design of wideband pulsed type gamma-ray sensors. These sensors were manufactured based on the design results and after word electrical properties were analyzed. The sensor input parameters were derived on the basis of pulsed gamma-ray spectrum and time-dependent energy rate, and the output current which were derived on the basis of the sensor sensitivity control circuit. Pulsed gamma-ray sensors were designed using the TCAD simulators. The design results show that the optimal Epi layer thickness is 45um with the applied voltage 3.3V and the diameter is 2.0mm. The doping concentrations are as follows : N-type is an Arsenic as $1{\times}10^{19}/cm^3$, P-type is a Boron as $1{\times}10^{19}/cm^3$ and Epi layer is Phosphorus as $3.4{\times}10^{12}/cm^3$. The fabricated sensor was a leakage current, 12pA at voltage -3.3V and fully depleted mode at voltage -5V. A test result of pulsed radiation shows that the sensor gives out the optimal photocurrent.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.24 no.3
• /
• pp.537-542
• /
• 1997

Chloral hydrate is one of the most widely used sedative agents to control the difficult-to-treat young age group in the dental clinic. The normal onset time of oral Chloral hydrate is 30-45 minute with some variations. We are often frustrated see the patient still awake and cry with agitation even after far more than the normal onset time. In such a case, the patient has to be rescheduled for another sedation visit with different agents and/or routes which greatly disappoints the guardians. This case report presents a sedative regimen that can possibly help the clinician complete scheduled treatment without postponement. We have tried additional administration of Midazolam intranasally to 22 patients of those who failed to respond properly to the initial dose(50-75mg/kg) of oral Chloral hydrate. The average age and weight of the patients was 34.2 months(22-61 mos.) and 15.2 kg(10-17 kg) respectively. Half of the regular dose of Midazolam(0.1mg/kg) was administered intranasally. using needless syringe in 42 cases without notable resistance of the patient. The onset was very rapid in most cases and colud proceed the treatment under the constant monitoring by Pulse oximeter. All the planned procedures could be completed in 93.2 % (69.4% of 'Good' plus 23.8% of 'Fair' rating)with only 6.8 %('Poor' rating) of failure rate. Evidence of adverse effect was not detected or reported during and/or after the procedures.

• ALGAE
• /
• v.32 no.4
• /
• pp.325-336
• /
• 2017

Intertidal community recovery and resilience were investigated with quantitative and qualitative perspectives as a function of disturbance timing. The study was conducted in a lower intertidal rock bed of the southern coast of South Korea. Six replicates of artificial disturbance of a $50cm{\times}50cm$ area were made by clearing all visible organisms on the rocky substrate in four seasons. Each of the seasonally cleared plots was monitored until the percent cover data reached the control plot level. There was a significant difference among disturbance timing during the recovery process in terms of speed and community components. After disturbances occurred, Ulva pertusa selectively preoccupied empty spaces quickly (in 2-4 months) and strongly (50-90%) in all plots except for the summer plots where non-Ulva species dominated throughout the recovery period. U. pertusa acted as a very important biological variable that determined the quantitative and qualitative recovery capability of a community. The qualitative recovery of communities was rapid in summer plots where U. pertusa did not recruit and the community recovery rate was the lowest in winter plots where U. pertusa was highly recruited with a long duration of distribution. In this study, U. pertusa was a pioneer species while being a dominant species and acted as a clearly negative element in the process of qualitative recovery after disturbance. However, the negative effect of U. pertusa did not occur in summer plots, indicating that disturbance timing should be considered as a parameter in understanding intertidal community resilience in temperate regions with four distinct seasons.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2011.06a
• /
• pp.76-76
• /
• 2011

선박이나 산업 플랜트에서 파이프 또는 탱크류의 맞대기 용접 시 안정적인 이면비드의 형성은 매우 중요하다. 대부분의 현장에서 파이프 맞대기 초층용접부의 안정적인 이면비드를 형성하기 위해 3mm의 루트갭을 띄우고 루트면이 없는 V-그루브에서 필러를 사용하는 수동 TIG용접을 주로 사용하고 있다. 수동 TIG용접은 고품질의 비드와 우수한 아크안정성, 그리고 용접인자의 제어가 쉽다는 장점이 있다. 그러나 수동 TIG용접은 용접속도가 10cpm정도로 느리기 때문에 GMAW에 비해 생산성이 낮고 작업자의 숙련도에 따라 품질이 변하게 된다. 본 연구에서는 높은 생산성과 기준갭 1.5mm에서 단차의 허용공차를 크게 하기 위해 루트면 3mm를 가지는 U-그루브의 설계를 하였으며, 두꺼운 루트면을 가지는 그루브에서 안정적인 이면비드를 형성시키기 위해 GMAW에서 아크 충격량에 대한 검토를 실시하였다. GMAW의 아크력이 용입에 어떠한 영향을 미치는지 검토하기 위해 수냉되는 동판에 갭을 1.5mm 띄우고 동일한 용착량과 입열량에서 아크력만을 변화시켜 실험하였다. 또한, U-그루브의 루트부를 모델링하여 두께3t의 평판시편을 각각의 갭과 단차 조건에서 실험하였다. 이 때, 기준갭 1.5mm에서 갭에 의해 생기는 단면적을 기준 갭단면적, 갭이 증가함에 따라 증가되는 단면적을 추가 갭단면적, 갭이 감소함에 따라 감소하는 단면적을 감소 갭단면적으로 정의하였다. 용접 중 발생하는 추가, 감소 갭단면적에 대하여 용착량을 50%의 수준으로 증가, 감소 시켰다. 갭에 따라 아크력을 변경하여 실험을 실시하였고 이면비드의 형상을 확인 하였다. 마지막으로 평판 시편의 조건에서 안정적으로 이면비드가 형성된 조건을 pipe U-그루브에 적용하였다. 그 결과 동판에서 용착량과 입열량이 같음에도 불구하고 아크력이 증가함에 따라 용입이 깊어짐을 확인하였다. 또한. 3t 평판시편에서 아크력의 제어를 통해 큰 단차와 갭이 있을 때, 안정적인 이면비드를 얻을 수 있는 조건을 확립하였다. 마지막으로 pipe U-그루브에서 앞선 실험의 용접조건으로 갭과 단차의 변화에 대해 실험을 하였으나, 시험편의 두께차이에 의한 전도 열손실로 인해 이면비드의 형성이 어려웠고, 아크 충격량의 증가를 통해 이러한 문제를 해결하였다.

• Herbal Formula Science
• /
• v.17 no.1
• /
• pp.45-59
• /
• 2009

To beef up natural immunity, we have used Bojoongikgitang which has been known to treat enervation in the oriental medicine. This study is analyzed out structure material and the chief virtue of a prescription through Literature Study on Bojoongikgitang and Clinical Application. And this study is investigated to make sure of the necessity and additional symptoms in using Bojoongikgitang. The results are as follows : 1. It is regarded that the structure materials of Bojoongikgitang consist of Astragali Radix one jeon(錢) five poon(分), Ginseng Radix, Atractylodis Macrocephalae Rhizoma, Glycyrrhizae Radix one jeon for each, Citri Pericarpium, Angelicae Gigantis Radix five poon for each, Cimicifugae Rhizoma, Bupleuri Radix three poon for each. 2. The necessity symptoms in using Bojoongikgitang are a pale complexion, drowsy eyes(目無精光), vigorless, lethargy, sluggish talk. 3. The fittest prescriptions prior to the necessity symptoms in using Bojoongikgitang are Bojoongikgitang added Paeoniae Radix Alba, Scutellariae Radix in fever, exterior heat, mild fever, Bojoongikgitang added Ephedrae Radix, Tritici Fructus Levis, Aconiti Iateralis Preparata Radix in spontaneous sweating, spontaneous sweating by yang deficiency, Bojoongikgitang added Paeoniae Radix Alba, Scutellariae Radix in feeling the pulse like a flood, largeness and weakness, scatter and largeness, flood and largeness for diagnosis respectively. Bojoongikgitang Entering the heart channel by culturing the blood prescription in vexation, vexation and anxiety, Soongihwajoongtang in headache, DossiBojoongikgitang in rigor, Bojoongikgitang annexed Saengmaecsan in thirst, Daninsamtang or Jojoongikgitang in asthma, asthma by congestion of the upwardness, Eeegongsan in light eating, eschewing food, losing one's appetite, Ikweeseungyangtang in deficiency failing to control blood and blood collapsey. 4. To treat a functional disease is superior to organic one in using Bojoongikgitang.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.12
• /
• pp.1033-1044
• /
• 2002

In this Paper, a new FRAM design technique utilizing grounded-plate PMOS-gate (GPPG) ferroelectric cell is proposed. A GPPG cell consists of a PMOS access transistor and a ferroelectric data storage capacitor. Its plate is grounded. The proposed architecture employs three novel methods for cell operation: 1) $V_{DD}$ -precharged bitline, 2) negative-voltage wordline technique and 3) negative-pulse restore. Because this configuration doesn't need the plate control circuitry, it can greatly increase the memory cell efficiency. In addition, differently from other reported common-plate cells, this scheme can supply a sufficient voltage of $V_{DD}$ to the ferroelectric capacitor during detecting and storing the polarization on the cell. Thus, there is no restriction on low voltage operation. Furthermore, by employing a compact column-path circuitry which activates only needed 8-bit data, this architecture can minimize the current consumption of the memory array. A 4- Mb FRAM circuit has been designed with 0.3-um, triple-well/1-polycide/2-metal technology, and the possibility of the realization of GPPG cell architecture has been confirmed.

• Journal of Energy Engineering
• /
• v.14 no.1
• /
• pp.37-45
• /
• 2005

The fuel cell system is one of very useful energy sources. The system has advantages as renew-able and environmental sources. To obtain AC electricity from fuel cells, inverters are necessary. A multilevel converter is used as an inverter for a high power fuel cell system. Through harmonic analysis, it is shown that the harmonic components and THD increase while fundamental component decreases as voltage sag increases. To solve the voltage sag problems, three different approaches are investigated in this paper; installation of a boost converter at the fuel cell output, control of pulse widths, and use of ultracapacitors. The proposed three approaches are analyzed and compared using simulation and experimental results.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.4
• /
• pp.93-100
• /
• 2002

The current from the feed motor of a machine tool contains substantial information about the machining state. There have been many researches that investigated the current as a measure for the cutting farces. However it has been reported that this indirect measurement of the cutting farces from the feed motor current is only feasible in low frequency. In this research, it was presented that the bandwidth of the current monitoring can be expanded to 130 Hz. And the unusual behavior of the current was examined in this bandwidth. The cross-feed directional cutting force influences the machined surface of the workpiece, which makes it necessary to estimate this force to control the roughness of the machined sulfate. The current exists in the stationary feed motor, and it can give the useful information on the quality of the machined surface. But the unpredictable behavior of the current prevents applying the current to prediction of the cutting state. Empirical approach was conducted to resolve the problem. As a result, the current was shown to be related to the accumulation of the accumulation of the infinitesimal rotation of the motor. rotation of the motor. Subsequently the relationship between the current and the cutting force was identified.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.36S no.12
• /
• pp.10-19
• /
• 1999

Cellular Automata Neural Systems(CANS) are neural networks based on biological development and evolution. Each neuron of CANS has local connection and acts as a form of pulse according to the dynamics of the chaotic neuron. CANS are generated from initial cells according to the CA rule. In the previous study, to obtain the useful ability of CANS, we make the pattern of initial cells evolve. However, it is impossible to represent all solution space, so we propose an evolving method of CA rule to overcome this defect in this paper. DNA coding has the redundancy and overlapping of gene and is apt for the representation of the rule. In this paper, we show the general expression of CA rule and propose translation method from DNA code to CA rule. The effectiveness of the proposed scheme was verified by applying it to the navigation problem of autonomous mobile robot.

• Journal of Periodontal and Implant Science
• /
• v.29 no.4
• /
• pp.861-872
• /
• 1999

Since pathologic changes of exposed root surface inhibit cell attachment and new attachment of connective tissue have been made, many efforts were apply to change the exposed root surface condition. Scaling and root planing can not remove the endotoxin completely and forms the smear layer which prohibits the new attachment of connective tissue. Therefore, many kinds of chemicals were used for controlling the pathologic change of the root surface. The purposes of this study was to compare and observe the changes of the exposed root surface treated by scaling and root planning, Tetracycline HCl and Argon Laser. After the scaling and root planning of ten extracted premolars, the differences & the root surface among groups were observed under SEM. Control group showed smear layer and irregular amorphous surface. The dentinal tubule was not exposed. The debris and scale like texture were also observed. Tetracycline HCl treated group showed relatively smooth surface and the collagen fiber was observed in the dentinal tubule. Argon Laser treated group showed the most effective results under the conditions of 0.8 to 1.0w irradiation for 0.5 to 1.0 sec with pulse wave. The results of this study showed that the root surface change was associated with the intensity and the duration of Argon Laser irradiation. Further investigation for the surface change with the Argon Laser irradiation is recommended for understanding of clinical effect.