• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.813-816
• /
• 2006

Complex pressure pulsation phenomenon in fuel rails is generated by rapid opening and closing of injectors and it commonly causes undesirable noise. In this study, fluid-structure interaction analyses based on CFD and FEM have been conducted to examine the pulsation damping characteristics for different shapes of fuel rails. It is shown from the present results that the fuel rail with a high aspect ratio rectangular cross section seems to be best in order to reduce the pressure pulsations. It also agrees well with the previous experimental test by Mizuno, K. et al.

• Proceedings of the Optical Society of Korea Conference
• /
• 2003.02a
• /
• pp.160-161
• /
• 2003

완전 광 3R(Retiming, Reshaping, Reamplification) 재생기는 WDM 시스템과 광 네트워크의 크기를 쉽게 확장시키기 위하여 필요한 매우 중요한 소자이다. 완전 광 3R 재생기의 구현에서 입력 광 신호로부터 광 클락을 추출하는 기술은 매우 중요한 기술이다. 이러한 광 클락 추출기술을 구현하기 위하여 모드락 레이저 다이오드와 다중 전극 OFB 레이저에서 self-pulsation 현상을 이용하는 방법이 많이 연구되고 있다. 모드락 레이저 다이오드를 이용한 방법은 모드 락킹 주파수가 레이저의 공진기의 길이에 의해서 결정되기 때문에 공진기의 길이를 정확하게 조절해야 한다는 단점을 가지고 있는 반면에 다중 전극 DFB 레이저의 경우 self-pulsation 주파수를 전기적으로 튜닝할 수 있다는 장점을 가지고 있다. (중략)

• Nuclear Engineering and Technology
• /
• v.55 no.4
• /
• pp.1310-1323
• /
• 2023

A reactor coolant pump (RCP) is essential for transporting coolant in the primary loop of pressurized water reactors. In the advanced passive reactor, the absence of a long pipeline between the steam generator and RCP serves as a transition section, resulting in a non-uniform flow field at the pump inlet. Therefore, the characteristics of the pump should be investigated under non-uniform flow to determine its influence on the pump. In this study, the pressure pulsation characteristics were examined in the time and frequency domains, and the sources of low-frequency and high-amplitude signals were analyzed using wavelet coherence analysis and numerical simulation. From computational fluid dynamics (CFD) results, non-uniform inflow has a great effect on the flow structures in the pump's inlet. The pressure pulsation in the pump at the rated flow increased by 78-128.7% under the non-uniform inflow condition in comparison with that observed under the uniform inflow condition. Furthermore, a low-frequency signal with a high amplitude was observed, whose energy increased significantly under non-uniform flow. The wavelet coherence and CFD analysis verified that the source of this signal was the low-frequency pulsating vortex under the steam generator.

• International Journal of Fluid Machinery and Systems
• /
• v.6 no.3
• /
• pp.121-136
• /
• 2013

This paper reports the 1-D fluid transient simulation results of the discharge flow conditions in a 6-cylinder reciprocating slurry pump. Two discharge manifold configurations are studied comparatively; a case with a hexagon shaped discharge manifold where each cylinder discharges at a single vertex, and a case where all the cylinders discharges are lumped together into a tank shaped manifold. In addition, the study examines the effect of two pulsation mitigation measures in the case of hexagonal manifold; a single inline orifice in one of the hexagon sides and a volumetric dampener at the manifold outlet. The study establishes the pressure and flow fluctuation characteristics of each configuration and decouples the pulsation characteristics of the pump and the discharge manifold.

• Journal of the korean Society of Automotive Engineers
• /
• v.12 no.3
• /
• pp.63-70
• /
• 1990

In a premixed flame stabilized by a streamlined step, the flame structure and combustion characteristics were investigated to identify the effect of the pressure pulsation in a combustion air. A flame stabilizing limits, visualization, mean temperature, ion current and gas concentration (O$_{2}$, CO$_{2}$, CO, UHC) were measured. With the combustion air of higher pressure pulsation, the development of the mixing layer was fast and wide, the temperature and combustion intensity were higher at arbitrary section. But, the effect was notably decreased with X=150 mm downstream. And a first eddy formation from step edge was earlier. Thus, with the combustion air of higher pressure pulsation, high rate of heat generation was expected.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.1
• /
• pp.88-95
• /
• 2000

In this paper, an expansion-resonator type pulsation attenuator is proposed to absorb and attenuate flow an pressure ripple with high frequencies generated from hydraulic control systems. The basic principle of a pulsation attenuator proposed here is applied to propagation, reflection, absorption of pressure waves at the cross section of discontinuity and resonance in the pipeline. It has advantage of the compact size and high degree fo freedom for installation in hydraulic systems. The design scheme based on distributed parameter pipeline system with dissipative viscous compressible model is developed. To investigate the reduction of flow and pressure ripple with high frequencies produced by swash plate type axial piston pump, two kinds of attenuators are manufactured. It is experimently confirmed that the spectral intensity of flow and pressure ripple with high frequencies from the pump are reduced up to about 20$^{\circ}$~30dB by using attenuators proposed here. The calculated results were in good agreement with the measured values. From there sults of this study, it is shown that an expansion-resonator type pulsation attenuator is effective in a wide frequency ranges to attenuate the flow and pressure ripple from hydraulic components.

• Korean Journal of Optics and Photonics
• /
• v.18 no.1
• /
• pp.56-65
• /
• 2007

The effect of gain dispersion on the self-pulsation (SP) characteristics due to the mode beating of two modes emitted in a multisection DFB laser composed of two complex-coupled DFB sections and a phase control section is investigated. When the peak wavelength, ${\lambda}_{p}$, of the gain spectrum of the DFB section is positioned in the center of the lasing wavelengths or the Bragg wavelengths of the two DFB sections, the maximum SP frequencies are higher and the modulation index has better characteristics compared to those cases for ${\lambda}_{p}$ fixed at the lasing wavelength or Bragg wavelength of one DFB section, when the difference between the Bragg wavelengths of the two DFB sections, ${\Dalta}{\lambda}_{B}$, is varied. When ${\lambda}_{p}$ is positioned in the renter of the Bragg wavelengths of the two DFB sections, the maximum SP frequency is higher and of the modulation index has better characteristics compared to those of the case for ${\lambda}_{p}$ positioned in the center of the lasing wavelengths of the two DFB sections.

• Korean Journal of Optics and Photonics
• /
• v.16 no.1
• /
• pp.85-98
• /
• 2005

As the number of compound cavity modes within the stopband of DFB sections decreases, the frequency of mode hopping decreases for the variation of $\Delta$λ$_{B}$, which represents the difference between the Bragg wavelengths of two DFB sections, so that the number of abrupt changes of pulsation frequencies decreases. In addition, the pulsation frequency varies continuously for the variation of the phase in a phase tuning section for a fixed $\Delta$λ$_{B}$. The number of compound cavity modes within the stopband decreases as the length of DFB sections increases and the length of a phase tuning section decreases. Thus stable self-pulsation operations for the variation of $\Delta$λ$_{B}$ and the phase in a phase tuning section could be obtained by proper selection of the coupling strength and the length of each section.ction.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.11
• /
• pp.1029-1035
• /
• 2011

Pressure pulsation of exciting sources that generally occurs on the piping system connected to the discharge of BFP(boiler feed water pump) in power plants causes wave reflection, wave interference, resonance, standing wave and so on. But if the operating speed of the pump is changed, the state of the noise and vibration can be done because characteristics of the exciting source are changed. This paper is to investigate the cause of the noise and vibration occurring on the piping system when the operating speed of BFP is down in accordance with lowering of the power generation. It is approached to two points of view ; Firstly, it is examined whether the pulsation source impacts on the shell mode vibration that vibrates radially across the cross-section of the pipe. But it doesn't affect the shell mode as much as the resonance occurs. Secondly, to find the relation between the pulsation source and the acoustic mode of the piping system, analysis for the piping system by indirect BEM(boundary element method) is carried out. Therefore it is investigated that the mechanism of the noise and vibration relates with acoustic mode of the piping system.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.7
• /
• pp.1034-1043
• /
• 2009

Hydrogen energy is becoming popular day by day due to its renewability and pollutaaant free natures. Hydrogen gas pressure which is after passing through reciprocating compressor part has high pulsation wave form. A unit, snubber is used as compressor components to reduce the harmful pulsation waveform and to remove the impurities in the hydrogen gas. An experiment has been conducted to investigate the pulsation reduction performance of different arrangement of snubber i.e. snubber array used in reciprocating compression system. Analyzing the snubber array experimental data, it is found that the pressure fluctuations are reduced from 90.1977% ~ 92.6336% with pressure loss 1.5013% ~ 4.9034% for compressor operation at different speed which ensure the good performance of snubber-array as pulsation damper in hydrogen compressing system.