• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.2
• /
• pp.130-135
• /
• 2015

Recently, as a result of the application of large and multi-blade propellers with high efficiency for large vessels, the vertical bending stiffness of propulsion shafting system tends to be declined. For some specific vessels, the shaft arrangement leads to the forward stern tube bearing to be omitted, decreasing vertical bending stiffness. In this respect, decreased vertical bending stiffness causes the problem which is the blade order resonance frequency to be placed within the operational rpm range of propulsion shafting system. To verify whirling vibration, the measurement should be carried out covering from operating rpm up to target rpm, however, the range is un-measurable generally. In order to resolve the measurement issue, this study shows the measuring method and the assessment method of relevant natural frequency of whiling vibration by using measured harmonic order component of whirling vibration.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.416-422
• /
• 2007

Prime movers in most large merchant ships adapt two stroke low speed diesel engine which has higher efficiency, mobility and durability. However, severe torsional vibration in these diesel engines may be induced by higher fluctuation of combustion pressures. Consequently, it may lead sometimes to propulsion shafting failure due to the accumulated fatigue stresses. Shaft fatigue strength analysis had been done traditionally in time domain but this method is complicated and difficult in analysing bi-modal vibration system such as the case of cylinder misfiring condition. In this paper authors introduce an assessment method of fatigue strength estimation for propulsion shafting system with two stroke low speed diesel engine in the frequency domain.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.06a
• /
• pp.1113-1119
• /
• 2005

The power electric system is one of the most concerning factor for the reliability of the electric propulsion ship. operation in higher temperature decreases the device's reliability and power efficiency. the management of power loss and temperature of switching devices is indispensable for the reliability fo the power electric system. In this paper, IGBT chip of the switching devices is modeled and MIIR(Motor with Inverter Internal to Rotor)type of the propulsion motors is used. these parts interact with each other to calculate the loss and temperature of device. calculated Results is modeled and designed of the control and monitoring system for the electric propulsion system.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.742-748
• /
• 2003

As for marine propulsion shafting system using 4 stroke diesel engine, it is common to apply reduction gear box between diesel engine and shafting with a view of increasing mechanical efficiency, which inevitably require elastic coupling due to avoid chattering and hammering inside of gear box. In this study, optimum method of rectifying propulsion shafting system in case of 750ton fishing vessel specially in a view of torsional vibration, is theoretically studied. After exchange of diesel engine and gear box, analysis result of torsional vibration get worse and so some countermeasure are needed. The elastic coupling is modified from present block type rubber coupling showing relatively high torsional stiffness to rubber coupling with two series elements directly connected. The vibration measurement using two laser torsion meters was done during sea trial, whose results are compared to those of calculation and verified.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.8 no.3 s.22
• /
• pp.18-23
• /
• 2005

Ships have been propelled and maneuvered by electrical drives since trle late seventies. Recently, rare earth PMs allow the design of brushless motors with very high efficiency over a wide speed range. This is the most important factor in ship propulsion technology. Several types PM motors have been developing for ship propulsion system. However these have disadvantage such as cogging torque. It causes an undesired effect that contributes to output ripple, vibration, and noise of machine. Therefore several techniques may be adopted in designing PM motor in order to reduce the cogging torque. This paper describes cogging torque receding methods such as adjusting arigap length, magnet arc, and magnet thickness. That are analysed by using the finite element method(FEM) and the maxwell stress tensor method.

• Journal of the Society of Naval Architects of Korea
• /
• v.41 no.3
• /
• pp.13-21
• /
• 2004

This paper deals with a theoretical and experimental method for the design of a biased asymmetric pre-swirl stator propulsion system which is an energy saving device by recovering a propeller rotational energy. In the case of slow-speed ships, the upward flow is generated along the afterbody hull form at the propeller plane. The generated upward flow cancels the rotating flow of the propeller at the starboard part while it increases at port part. The present biased asymmetric pre-swirl stator propulsion system consists of three blades at the port and one blade at the starboard which can recover the biased rotating flow effectively. This paper provides the design concept which gives more simple and a high degree of efficiency and the experimental results for the compound propulsion system.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.8 no.2
• /
• pp.95-101
• /
• 2004

An experimental investigation was conducted to investigate the effects of the equivalence ratio and air mass flux on the combustion efficiency in a solid fuel ramjet used fuel grains which were highly loaded with boron carbide. Combustion efficiency increased with increasing equivalence ratio (grain length), and decreasing air mass flux. Higher inlet air temperature produced higher combustion efficiencies, apparently the result of enhanced combustion of the larger boron particles those burn in a diffusion controlled regime. Short grains which considered primarily of the recirculation region produced larger particles and lower combustion efficiencies. The result of the normalized combustion efficiency increased with inlet air temperatures coincident with the result of the Brayton cycle thermal and the total efficiency relating to the heat input.

• International Journal of Railway
• /
• v.9 no.2
• /
• pp.41-45
• /
• 2016

In this paper, a study on the efficiency improvement of the magnetic levitation train using the LIM (Linear Induction Motor) was presented. The maglev train has the advantage of being environmentally friendly since much less noise and dust is produced. However, due to structural limitation, compared to a rotating induction motor, linear induction motor, the main propulsion engine of the maglev train has a relatively greater air gap and hence has the lower operation efficiency. In this paper, the relationship between the operating condition of the train and the slip frequency has been investigated to find out the optimum slip frequency that might improve the efficiency of the magnetic levitation train with linear induction motor. The slip frequency is variable during the operation by this relationship only within a range that does not affect the levitation system of the train. After that, the comparison of the efficiency between the conventional control method with the slip frequency fixed at 13.5[Hz] and the proposed method with the slip frequency variable from 9.5[Hz] to 6.5[Hz] has been conducted by simulation using Simplorer. Experiments of 19.5[ton] magnetic levitation trains owned by Korea Institute of Machinery and Materials were carried out to verify the simulation results.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.1
• /
• pp.18-24
• /
• 2015

An experimental investigation was conducted to figure out the effects of the inlet air temperature on the combustion efficiency using the fuel grains which were highly loaded with boron carbide. The results showed that the normalized combustion efficiency increased with the inlet air temperature, apparently the result of enhanced combustion of the boron particles. Even though the combustion efficiency is increased, the overall efficiency through the semi-empirical method, is decreased with the increasing inlet air temperature. Brayton cycle analysis has been performed using the heat input parameter and combustor Mach number, those two parameters are important role for the performance and similar trends are shown at the experimental results.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.20 no.6
• /
• pp.91-100
• /
• 2016

Efficiency characteristics of centrifugal turbopumps for a liquid rocket engine were investigated. Predicting the performance of pumps for a turbopump assembly test, the variation on pump efficiency by working fluids was analyzed from pump component tests. Water and liquid nitrogen (LN2) were used for the component test, kerosene (Jet A-1) and liquid oxygen (LOX) were adapted for the turbopump assembly (TPU) test as working fluids. Overall performance of the pumps was investigated covering design/off-design operating points and the pump efficiency on the environment of real media (LOX/kerosene) could be modified from the pump component tests.