• Journal of Korean Society of Forest Science
• /
• v.53 no.1
• /
• pp.44-55
• /
• 1981

Neutral sulfite precooked fir chips were refined in the Asplund Laboratory Defibrator at various temperature ($20^{\circ}C$, $120^{\circ}C$ and $180^{\circ}C$). The effects of refining temperatures on the physical property and morphological structure of the resulting pulps were discussed. Yields of precooked chips (84%, 92% and 100%) and refining temperature affected remarkably the yield of refined pulp, its beatability, sheet strength and morhphological characteristics. Pulp yield and beatability decreased with increasing refining temperature. Fiber surface of unbeaten pulp from precooked chips of 84% yield was to some extent covered by the secondary wall, while that of the pulp form precooked yield of 92% by the compound middle lamella. In the case of uncooked chips, fibers were damaged heavily, and the exposed fiber surface resulted from the equal amount of the secondary wall and the compound middle lamella. In the case of pulps prepared from precooked chips of higher yields (92% and 100%), sheet strength increased linearly as sheet density increased. But at the same sheet density, pulp from lower precooked yield (84%) had better sheet strength after open discharge refining as compared to pressurized refining, because pulp from the former had much amounts of fines fraction of higher water retention value than the latters. And there was observed a little difference in fiber length distribution but nearly similar in its morphology with increasing refining temperature.

• The Korean Journal of Nuclear Medicine
• /
• v.34 no.1
• /
• pp.62-73
• /
• 2000

Purpose: Esophageal cancer patients have a difficulty in the intake of meals through the blocked esophageal lumen, which is caused by an ingrowth of cancer cells and largely influences on the prognosis. It is reported that esophageal cancer has a very low survival rate due to the lack of nourishment and immunity as the result of this. In this study a new radioactive stent, which prevents tumor ingrowth and restenosis by additional radiation treatment, has been developed. Materials and Methods: Using ${\ulcorner}HANARO{\lrcorner}$ research reactor, the radioactive stent assembly ($^{166}Ho$-SA) was prepared by covering the metallic stent with a radioactive sleeve by means of a post-irradiation and pre-irradiation methods. Results: Scanning electron microscopy and autoradiography exhibited that the distribution of $^{165/166}Ho\;(NO_3)$ compounds in polyurethane matrix was homogeneous. A geometrical model of the esophagus considering its structural properties, was developed for the computer simulation of energy deposition to the esophageal wall. The dose distributions of $^{166}Ho$-stent were calculated by means of the EGS4 code system. The sources are considered to be distributed uniformly on the surface in the form of a cylinder with a diameter of 20 mm and length of 40 mm. As an animal experiment, when radioactive stent developed in this study was inserted into the esophagus of a Mongrel dog, tissue destruction and widening of the esophageal lumen were observed. Conclusion: We have developed a new radioactive stent comprising of a radioactive tubular sleeve covering the metallic stent, which emits homogeneous radiation. If it is inserted into the blocked or narrowed lumen, it can lead to local destruction of the tumor due to irradiation effect with dilatation resulting from self-expansion of the metallic property. Accordingly, it is expected that restenosis esophageal lumen by the continuous ingrowth and infiltration of cancer after insertion of our radioactive stent will be decreased remarkably.

• Korean Journal of Food Science and Technology
• /
• v.37 no.3
• /
• pp.438-442
• /
• 2005

Granule swelling is essential phenomenon of starch gelatinization in excess water, and characteristic of heated starch dispersion depends largely on size and distribution of swelled starch granule. Although swelling characteristic of starch granules depends on type of starch, heating rate, and moisture content, influence of heating rate on swelling phenomenon of starch granule has not been fully discussed, because constant heating rate of starch dispersion cannot be obtained by conventional heating method. Ohmic heating, electric-resistant heat generation method, applies alternative current to food materials, through which heating rate can be easily controlled precisely and conveniently at wide range of constant heating rates. Starch dispersion heated at low heating rates below $7.5^{\circ}C/min$ showed Newtonian fluid behavior, whereas showed pseudoplastic behavior at heating rates above $16.4^{\circ}C/min$. Apparent viscosity of starch dispersion increased linearly with increasing heating rate, and yield stress was dramatically increased at heating rates above $16.4^{\circ}C/min$. Average diameter of corn starch granules during ohmic heating was dramatically increased from $30.97\;to\;37.88\;{\mu}m$ by increasing heating rate from $0.6\;to\;16.4^{\circ}C/min$ (raw corn starch: $13.7\;{\mu}m$). Hardness of starch gel prepared with 15% corn starch dispersion after heating to $90^{\circ}C$ at different heating rates decreased gradually with increasing heating rate, then showed nearly constant value from $9.4\;to\;23.2^{\circ}C/min$. Hardness increased with increase of heating rate higher than $23.2^{\circ}C/min$.

• Journal of the Korean earth science society
• /
• v.21 no.5
• /
• pp.563-582
• /
• 2000

Two Cretaceous(80-90 Ma) non-marine sedimentary basins, Namyang and Tando Basins, are distributed in the Namyang area, Hwaseonggun and in the Tando area, Ansanshi, Kyungki Province, Korea. The Namyang and Tando Basins are composed of 10 facies, which are pooped into 5 facies associations(FA). FA I consists of massive conglomerate facies, normally graded conglomerate facies and reversely graded conglomerate facies, which is interpreted to have been formed by laminated sandstone facies, massive conglomerate facies(channelized), which is thought to have been formed by sheet flow, stream flow and suspension sedimentation in an alluvial/braided plain environment. FA III consists of massive mudstone(pebbly) facies, laminated mudstone facies, massive sandstone facies and is interbedded by channel-fill conglomerate. It is interpreted to have been deposited by suspension settling during flooding and channel-fill deposition in a floodplain environment. FA IV consists of massive conglomerate facies, normally graded conglomerate facies, massive sandstone facies, normally graded sandstone facies, and laminated sandstone facies and is interbedded with mudstone facies. It is thought to have been deposited by debris flow and turbidity current in a fan-delta environment. FA V consists of massive mudstone facies, laminated mudstone facies, laminated sandstone facies and is interbedded by massive conglomerate bed. It is thought to have been formed by suspension sedimentation and low-density turbidity current in a lake. In the Namyang Basin FA I is distributed in the eastern and southern margin of the basin, FA II in the middle part of the basin as north-south tending band. and FA III in the western part. In the Tando Basin FA II is distributed in the middle part of eastern margin and in the northwestern margin, FA IV in the southwestern part, and FA V in the central part. Correlation of the facies associations shows that FA I and II in the Namyang Basin are distributed in the lower to middle part of stratigraphic sequence and FA III in the upper part of the sequence whereas FA II and IV in the Tando Basin are in the lower to middle part and FA V in the upper part of the sequence. These patterns of facies associations distribution suggest that the Namyang Basin was developed as an alluvial fan and alluvial/braided plain at first and then evolved into a floodplain whereas the Tando Basin was developed as a fan-delta and alluvial/braided plain at first and then evolved into a lake environment.

• Journal of the Korean earth science society
• /
• v.33 no.7
• /
• pp.569-582
• /
• 2012

The heavy rainfalls caused large property damages and human casualties. For example, Changma caused 0.25 billion dollars in damages and 57 deaths and 112 missing by accompanying the torrentially convective heavy rainfall in Seoul, 2011. In addition, TY15 (Bolaven) caused a small damage by bringing a relatively small amount of rainfall and strong wind in Gwanju, 2012. The investigation and analyses of these mesoscale processes of rainfall events for different physical properties using KLAPS for weather environments of the above cases were performed. These typical and ideal meoscale systems by better and more favorable cloud systems were chosen to retrieve rain intensity from Radar and Chullian data. The quantitative rain intensities of Radar and Chullian differ greatly from the ground-based gauge values with underestimating over 50 mm/hr at the peak time of hourly maximum rain intensity about over than 85 mm/hr. However, the Radar rain intensity demonstrated approximately lower than 35 mm/hr, and the Chullian rain intensity less than 60 mm/hr for Changma in Seoul, 2011. For typhoon (TY15, Bolaven) in Gwangju, similarly, the quantitative rain intensities of Radar and Chullian differ from the ground-based gauge values. At the peak time, the hourly maximum rain intensity of ground-based gauge was more than 15 mm/hr. However, the Radar rain intensity showed lower than 5 mm/hr, and the Chullian rain intensity lower than 10 mm/hr. Regarding the above two cases of typhoon and Changma, even though Radar and Chullian rain intensities have been underestimated when compared to the ground-based rain intensity, the distributions of time scale features of both Radar and Chullian rain intensities still delineated a similar tendency of rain intensity distribution of the ground-based gauge data.

• Korean Journal of Soil Science and Fertilizer
• /
• v.43 no.2
• /
• pp.160-165
• /
• 2010

To reduce the dose of fertilizers is very important to sustainable production of many horticultural crops, including strawberry. In order to practice the environment friendly agriculture of strawberry cultivation in plastic film house, soil chemical properties of 435 soil samples (232 for loam, 83 for sandy loam, and 120 for silt loam) in Chungnam Province from2008 to 2009 were determined. The average of pH, EC, OM, Av. $P_2O_5$, Ex. $K^+$, Ex. $Ca^{2+}$, Ex. $Mg^{2+}$, and Ex. $Na^+$ was 6.5, 2.28 dS $m^{-1}$, 26 g $kg^{-1}$, 910 mg $kg^{-1}$, 1.09 $cmol_c\;kg^{-1}$, 8.3 $cmol_c\;kg^{-1}$, 2.5 $cmol_c\;kg^{-1}$, and 0.58 $cmol_c\;kg^{-1}$, respectively. The content of Av. $P_2O_5$ in sandy loam soil was significantly higher than silt loam soil, whereas other properties showed no difference between soil texture. The kinds of strawberry cultivars showed no difference in soil chemical properties. The frequency distribution within optimum range of soil chemical properties was 30.6%, 35.4%, 37.0%, 5.3%, 8.5%, 8.5%, and 17.9% for pH, EC, OM, Av. $P_2O_5$, Ex. $K^+$, Ex. $Ca^{2+}$, and Ex. $Mg^{2+}$, respectively. Especially, excessive portion of Av. $P_2O_5$, and Ex. $Ca^{2+}$ were high 86.9%, and 86.0%, respectively. EC values of soil samples were significantly positive correlatoin with all chemical properties except soil pH. In principle component analysis of chemical properties in soil samples, the percentage of variance explained by PC 1 was 38.8%, while PC 2 explained 17.8%of the variance, for a cumulative total of 56.6%. These results were able to distinguish between soil textures and strawberry cultivars. Also, these results considered that understanding of soil chemical properties under using principal component analysis be able to improve amounts of fertilizers for sustainable agriculture in plastic film house.

• Journal of the Mineralogical Society of Korea
• /
• v.22 no.1
• /
• pp.23-34
• /
• 2009

The adsorption of iodide on untreated bentonite and bentonites modified with organic cation (i.e., hexadecylpyridinium chloride monohydrate ($HDP^+$)) was investigated, and the organobentonites were characterized using uptake measurements, ${\mu}$-XRD, and electrophoretic mobilities measurement. Uptake measurements indicate that bentonite has a high affinity for $HDP^+$. Our ${\mu}$-XRD study indicates that organobentonites significantly expanded in basal spacing and organic cations were substantially intercalated into the interlayer spaces of bentonite. The electrophoretic mobility indicates that organobentonite tht is modified with organic cations in excess of the CEC of bentonite is completely different from untreated bentonite in the surface charge distribution. We found significant differences in adsorption capacities of iodide depending on the bentonite properties as follows: iodide adsorption capacities were 439 mmol/kg for the bentonite modified with $HDP^+$ at an equivalent amount corresponding to 200% of the CEC of bentonite whereas no adsorption of iodide was observed for the untreated bentonite. The molecular environments of iodine adsorbed on organobentonites were further studied using I K-edge and $L_{III}$-edge x-ray absorption spectroscopy (XAS). The X-ray absorption near-edge structure (XANES) of iodine spectra from organobentonites was similar to that of KI reference solution. Linear combination fitting of EXAFS data suggests the fraction of iodine reacted with the organic compound increased with increasing loading of the organic compound on organobentonites. In this study, we observed significant differences in the adsorption environments of iodide depending on the modified property of bentonite and suggest that an organobentonite has potential as reactive barrier material around a nuclear waste repository containing anionic radioactive iodide.

• Journal of the Korean Geotechnical Society
• /
• v.30 no.6
• /
• pp.23-39
• /
• 2014

An artificial rainwater reservoir installed in urban areas for recycling rainwater is an eco-friendly facility for reducing storm water effluence. However, in order to recycle the rainwater directly, the artificial rainwater reservoir requires an auxiliary system that can remove non-point source pollutants included in the initial rainfall of urban area. Therefore, the conventional soil filtration technology is adopted to capture non-point source pollutants in an economical and efficient way in the purification system of artificial rainwater reservoirs. In order to satisfy such a demand, clogging characteristics of the sand filter layers with different grain-size distributions were studied with real non-point source pollutants. For this, a series of lab-scale chamber tests were conducted to make a prediction model for removal of non-point source pollutants, based on the clogging theory. The laboratory chamber experiments were carried out by permeating two types of artificially contaminated water through five different types of sand filter layers with different grain-size distributions. The two artificial contaminated waters were made by fine marine-clay particles and real non-point source pollutants collected from motorcar roads of Seoul, Korea. In the laboratory chamber experiments, the concentrations of the artificial contaminated water were measured in terms of TSS (Total Suspended Solids) and COD (Chemical Oxygen Demand) and compared with each other to evaluate the performance of sand filter layers. In addition, the accumulated weight of pollutant particles clogged in the sand filter layers was estimated. This paper suggests a prediction model for removal of non-point source pollutants with theoretical consideration of the physical characteristics such as the grain-size distribution and composition, and change in the hydraulic conductivity and porosity of sand filter layers. The lumped parameter ${\theta}$ related with the clogging property was estimated by comparing the accumulated weight of pollutant particles obtained from the laboratory chamber experiments and calculated from the prediction model based on the clogging theory. It is found that the lumped parameter ${\theta}$ has a significant influence on the amount of the pollutant particles clogged in the pores of sand filter layers. In conclusion, according to the clogging prediction model, a double-sand-filter layer consisting of two separate layers: the upper sand-filter layer with the effective particle size of 1.49 mm and the lower sand-filter layer with the effective particle size of 0.93 mm, is proposed as the optimum system for removing non-point source pollutants in the field-sized artificial rainwater reservoir.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.24 no.2
• /
• pp.213-230
• /
• 2008

The aim of this study was to analyze the initial movement and the stress distribution of each tooth and periodontal ligament during the lingual lever-arm retraction of 6 maxillary incisors using FEA. Two kinds of finite element models were produced: 2-properties model (simple model) and 24-properties model (multi model) according to the material property assignment. The subject was an adult male of 23 years old. The DICOM images through the CT of the patient were converted into the 3D image model of a skull using the Mimics (version 10.11, Materialise's interactive Medical Image Control System, Materialise, Belgium). After series of calculating, remeshing, exporting, importing process and volume mesh process was performed, FEA models were produced. FEA models are consisted of maxilla, maxillary central incisor, lateral incisor, canine, periodontal ligaments and lingual traction arm. The boundary conditions fixed the movements of posterior, sagittal and upper part of the model to the directions of X, Y, Z axis respectively. The model was set to be symmetrical to X axis. Through the center of resistance of maxilla complex, a retraction force of 200g was applied horizontally to the occlusal plane. Under this conditions, the initial movements and stress distributions were evaluated by 3D FEA. In the result, the amount of posterior movement was larger in the multi model than in the simple model as well as the amount of vertically rotation. The pattern of the posterior movement in the central incisors and lateral incisors was controlled tipping movement, and the amount was larger than in the canine. But the amount of root movement of the canine was larger than others. The incisor rotated downwardly and the canines upwardly around contact points of lateral incisor and canine in the both models. The values of stress are similar in the both simple and multi model.

• Journal of Korean Society of Forest Science
• /
• v.89 no.5
• /
• pp.677-684
• /
• 2000

This study was conducted to investigate the relationship of development of root and soil condition and also to elucidate the difference between stands for mechanical and physical stability according to distribution of roots in the Norway Spruce (Picea abies [L.] Karst.) stands of 30 to 40 year of ages with different soil condition. In the root structure, remarkably different root pattern was shown among the three stands; Eberg$\ddot{o}$tzen stand showed large number f roots with much fine roots which deeply in vertical direction while Barbis stands had thicker root and small number of root than Eberg$\ddot{o}$tzen stand. The Weidenbrunnen stand showed differently half-vertical and plate root structure and the root developed not to be deeply compared to the other two stands. In the total number of root, Eberg$\ddot{o}$tzen stand had the most number of 74 and Barbis stand 33, Weidenbrunnen stand 57 respectively. Eberg$\ddot{o}$tzen stand had much more number of vertical root with 57 than the other two stand; Barbis 21 and Weidenbrunnen 36. In the total length of root, Weidenbrunnen stand showed to be longer than the other two stands and the length of horizontal root also showed longer. Regarding to the rates of horizontal root against vertical root, Eberg$\ddot{o}$tzen stand showed comparatively higher value as 1,2 than other two stands(0.5). In the total weight of root, Weidenbrunnen stand showed very high value compared with the other stands and ratio of vertical root against horizontal root was 0,16 which is very lower than the other two stands(0,4). The remarkable differences of root pattern of Norway spruce stands appeared in this study are through to be caused more by chemical property of soil such as acidity den the mechanical or physical factor of soil conditions.