• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.3
• /
• pp.249-256
• /
• 2006

Catalytic combustion of toluene was investigated on the Cu-Mn oxide catalysts prepared by the impregnation(Imp) and the deposition-precipitation(DP) methods. The mixing of copper and manganese has been found to enhance the activity of catalysts. It is then found that catalytic efficiency of the Cu-Mn oxide catalyst prepared by the DP method on combustion of toluene is much higher than that of the Cu-Mn oxide catalyst prepared by Imp method with the same chemical composition. The catalyst prepared by the deposition-precipitation method observed no change of toluene conversion at time on stream during 10 days and at the addition of water vapor. On the basis of catalyst characterization data, it has been suggested that the catalysts prepared by the DP method showed uniform distribution and smaller particle size on the surface of catalyst and then enhanced reduction capability of catalysts. Therefore, we think that the DP method leads on progressive capacity of catalyst and promotes stability of catalyst. It was also presumed that catalytic conversion of toluene on the Cu-Mn oxide catalyst depends on redox reaction and $Cu_{1.5}Mn_{1.5}O_4$ spinel phase acts as the major active sites of catalyst.

• Laboraroty Animal Research
• /
• v.34 no.4
• /
• pp.302-310
• /
• 2018

CD47 (integrin-associated protein), a multi-spanning transmembrane protein expressed in all cells including red blood cells (RBCs) and leukocytes, interacts with signal regulatory protein ${\alpha}$ ($SIRP{\alpha}$) on macrophages and thereby inhibits phagocytosis of RBCs. Recently, we generated a novel C57BL/6J CD47 knockout ($CD47^{-/-}$ hereafter) mouse line by employing a CRISPR/Cas9 system at Center for Mouse Models of Human Disease, and here report their hematological phenotypes. On monitoring their birth and development, $CD47^{-/-}$ mice were born viable with a natural male-to-female sex ratio and normally developed from birth through puberty to adulthood without noticeable changes in growth, food/water intake compared to their age and sex-matched wild-type littermates up to 26 weeks. Hematological analysis revealed a mild but significant reduction of RBC counts and hemoglobin in 16 week-old male $CD47^{-/-}$ mice which were aggravated at the age of 26 weeks with increased reticulocyte counts and mean corpuscular volume (MCV), suggesting hemolytic anemia. Interestingly, anemia in female $CD47^{-/-}$ mice became evident at 26 weeks, but splenomegaly was identified in both genders of $CD47^{-/-}$ mice from the age of 16 weeks, consistent with development of hemolytic anemia. Additionally, helper and cytotoxic T cell populations were considerably reduced in the spleen, but not in thymus, of $CD47^{-/-}$ mice, suggesting a crucial role of CD47 in proliferation of T cells. Collectively, these findings indicate that our $CD47^{-/-}$ mice have progressive hemolytic anemia and splenic depletion of mature T cell populations and therefore may be useful as an in vivo model to study the function of CD47.

• Structural Engineering and Mechanics
• /
• v.70 no.1
• /
• pp.67-80
• /
• 2019

Strengthening with near surface mounted carbon fibre reinforced polymers (NSM-CFRP) is a strengthening technique that have been used for several decades to increase the load carrying capacity of reinforced concrete members. In Iraq, many concrete buildings and bridges were subjected to a wide range of damage as a result of the last war and many other events. Accordingly, there is a progressive increase in the strengthening of concrete structures, bridges in particular, by using CFRP strengthening techniques. Near-surface mounted carbon fibre polymer has been recently proved as a powerful strengthening technique in which the CFRP strips are sufficiently protected against external environmental conditions especially the high-temperature rates in Iraq. However, this technique has not been examined yet under repeated loading conditions such as traffic loads on bridge girders. The main objective of this research was to investigate the effectiveness of NSM-CFRP strips in reinforced concrete beams under repeated loads. Different parameters such as the number of strips, groove size, and two types of bonding materials (epoxy resin and cement-based adhesive) were considered. Fifteen NSM-CFRP strengthened beams were tested under concentrated monotonic and repeated loadings. Three beams were non-strengthened as reference specimens while the remaining were strengthened with NSM-CFRP strips and divided into three groups. Each group comprises two beams tested under monotonic loads and used as control for those tested under repeated loads in the same group. The experimental results are discussed in terms of load-deflection behavior up to failure, ductility factor, cumulative energy absorption, number of cycles to failure, and the mode of failure. The test results proved that strengthening with NSM-CFRP strips increased both the flexural strength and stiffness of the tested beams. An increase in load carrying capacity was obtained in a range of (1.47 to 4.49) times that for the non-strengthened specimens. Also, the increase in total area of CFRPs showed a slight increase in flexural capacity of (1.02) times the value of the control strengthened one tested under repeated loading. Increasing the total area of CFRP strips resulted in a reduction in ductility factor reached to (0.71) while the cumulative energy absorption increased by (1.22) times the values of the strengthened reference specimens tested under repeated loading. Moreover, the replacement of epoxy resin with cement-based adhesive as a bonding material exhibited higher ductility than specimen with epoxy resin tested under monotonic and repeated loading.

• Women's Studies Review
• /
• v.29 no.2
• /
• pp.139-173
• /
• 2012

This paper examines the delayed situations for gender equality in South Korean, Japanese, and Taiwanese families despite the challenge to the gender division of labor in modern society, and to analyze the contradiction between the notions of gender equality and the experiences women face in East Asia countries. Using EASS data, we analyze the effective difference over the division of household labor according to women's age and length of school time, attitude for gender division of labor, couple's labor time, and family network. In South Korea and Taiwan, men's actual ratio of household division is higher than Japanese men's. On the other hand, Japanese women's ratio of household division is the highest in spite of their progressive attitude for gender equality. It is due to the difference of women's working time among the countries. In South Korea and Taiwan, women tend to work in full time job, so that they seem to inevitably reduce the time for household labor. The family characteristics have an effect on the women's ratio of household division in Taiwan, and the feature of women's employment does in South Korea. The high percentage of three-generation household contributes to the reduction of housework burden in Taiwan. In South Korea, the higher women's education levels, the higher the women's ratio of household division. Women's weakened bargaining power for household labor is due to the relatively low level of high-educated women's economic participation in South Korea. This paper reveals the effective factors on the gender division of household labor. We propose the necessity of the macro-level analysis as well as the analysis of the personal and conjugal feature.

• Proceedings of the Korean Society of Tobacco Science Conference
• /
• 1997.10a
• /
• pp.79-90
• /
• 1997

The world-wide cigarette market is becoming increasingly regulated. This involves restrictions on the freedom to advertise, restrictions on where people can smoke, and in some ways of most importance, limits on cigarette smoke deliveries. In particular, in an increasingly large number of countries maximum tar legislation is being enacted. In many cases, such as the European Union, this type of legislation is progressive and over time it is entirely conceivable that maximum permitted tar deliveries will be reduced to as low as 5 mg, possibly with additional restrictions on smoke nicotine deliveries. In addition, the pace of change is increasing as more and more countries embark on tar reduction programmes. The key challenge facing the cigarette industry is to manage these changes in such a way which ensures that product acceptability is maintained at as high a level as is possible in these circumstances. There are a number of ways of achieving this involving filter ventilation, modifying blends and using different filter constructions The real innovation comes when combining these in a way that gives the most acceptable balance of all these competing variables as far as the smoker is concerned. Undoubtedly, the nature of the filter is of crucial importance in designing the most acceptable low tar products, and this paper will discuss some of the filter types which are currently in use in the various low tar markets around the world. Also, some thoughts about the future in terms of new filter developments will be presented.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.10
• /
• pp.147-160
• /
• 2008

This paper presents the results of full-scale loading tests performed on 54 passive anchors and 4 group anchored footings grouted to various lengths at several sites in Korea. The test results, the failure mechanisms as well as uplift capacities of rock anchors depend mostly on rock type and quality, embedded fixed length, properties of the discontinuities, and the strength of rebar. Anchors in poor quality rocks generally fail along the grout/rock interfaces when their depths are very shallow (a fixed length of less than 1 m). However, even in such poor rocks, we can induce a more favorable mode of rock pull-up failure by increasing the fixed length of the anchors. On the other hand, anchors in good quality rocks show rock pull-up failures with high uplift resistance even when they are embedded at a shallow depth. Laboratory test results revealed that a form of progressive failure usually occurs starting near the upper surface of the grout, and then progresses downward. The ultimate tendon-grout bond strength was measured from $18{\sim}25%$ of unconfined compressive strength of grout. One of the important findings from these tests is that the measured strains along the corrosion protection sheath were so small that practically the reduction of bond strength by the presence of sheath would be negligible. Based on test results, the main parameters governing the uplift capacity of the rock anchor system were determined. By evaluation of the ultimate uplift capacity of anchor foundations in a wide range of in situ rock masses, rock classification suitable for a transmission tower foundation was developed. Finally, a very simple and economical design procedure is proposed for rock anchor foundations subjected to uplift tensile loads.

• Journal of Chest Surgery
• /
• v.32 no.5
• /
• pp.422-427
• /
• 1999

Background: Tachycardia induced heart failure model would be the model of choice for the dilated cardiomyopathy. This more closely resembles the clinical syndrome and does not require major surgical trauma, myocardial ischemia and pharmacological or toxic depression of cardiac function. When heart failure is progressive, application of new surgical procedures to the faling heart is highly risky. It has been shown that recovery trajectory from heart failure is a new method in decreasing animal mortality. The purpose is to establish the control datas for recovery trajectory in the canine heart failure model. Material and Method: 21 mongrel dogs were studied at 4 stages(baseline, at the heart failure, 4 and 8 weeks after recovery). Heart failure was induced during 4 weeks of continuous rapid pacing using a pacemaker. Eight weeks of trajectory of recovery period was allowed. Indices of left ventricular function and dimension were measured every 2 weeks and the hemodynamics were measured by use of Swan-Ganz catheterization and thermodilution method every 4 weeks. Values were expressed as mean${\pm}$standard deviation. Result: 4(20%) dogs died due to heart failure. Left ventricular end-diastolic volume at the 4 stages were 40.8${\pm}$7.4, 82.1${\pm}$21.1, 59.9${\pm}$7.7 and 46.5${\pm}$6.5ml. Left ventricular end-systolic volume showed the same trend. Ejection fractions were 50.6${\pm}$4.1, 17.5${\pm}$5.8, 36.3${\pm}$7.3, and 41.5${\pm}$2.4%. Blood pressure and heart rate showed no significant changes. Pressures of central vein, right ventricle, pulmonary artery, and pulmonary capillary wedge showed significant increase during the heart failure period, normalizing at the end of recovery period. Stroke volumes were 21.5${\pm}$8.2, 12.3${\pm}$3.5, 17.9${\pm}$4.6, and 15.5${\pm}$3.4ml. Blood norepinephrine level was 133.3${\pm}$60.0pg/dL at the baseline and 479.4${\pm}$327.3pg/dL at the heart failure stage(p=0.008). Conclusion: Development of tachycardia induced heart failure model is of high priority due to ready availability and reasonable amenability to measurements. Recovery trajectory after cessation of tachycardia showed reduction of cardiac dilatation and heart function. Application of new surgical procedures during the recovery period could decrease animal mortality.

• Korean Journal of Environmental Agriculture
• /
• v.13 no.2
• /
• pp.223-230
• /
• 1994

A practical study on a drying and fermentation system equipped with a stirring machine operated mechanically, of pig manure was conducted to prove the efficiency of and practicability to an ordinary pig farm. The type of the drying bed was a round-shaped (r=3m) concrete structure and the stirring machine was adopted to stir and transfer dried pig manure to the fermentation tank. The dried pig manure was put into a fermentation tank ($V=18m^3$), which was aerated from pipe lines installed at the bottom. While water content of pig manure passing through a drying bed was remarkably reduced than before drying, the drying efficiency of this system decreased in winter. However, the temperature of pig manure piled up in the fermentation room in winter reached over $60^{\circ}C$ and excess water of pig manure was removed during the fermentation process. The reduction rate of water content of pig manure, to which dried pig manure was added as bulking material on the drying bed, was 52.1%, but when dried without bulking material it was only 19.7%. Although the content of $P_2O_5$ of dried pig manure was slightly higher than that of fresh pig manure, progressive changes in chemical composition between fresh and dried pig manure made no great difference. Among the contents of minerals of fresh and dried pig manure, CaO was the highest and the rest were in the decreasing order of $K_2O$, MgO, and $Na_2O$. Population density of E. coli and Streptococci of dried pig manure was reduced by 142 and 236 times that of fresh pig manure, respectively. The installation cost of this drying and fermentation system was 4,185,630 won (approximately 5,232 US $) and operating cost per year was 190,000 won (237.5US $) on the basis of self-labor condition.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 1997.11a
• /
• pp.3-31
• /
• 1997

Water has always played a significant role in the lives of people. In urbanised Rome, with its million people. sophisticated supply systems developed and then fled with the empire. only to be rediscovered later But it was the industrial Revolution commencing in the eighteenth century that ushered in major paradigm shifts In use and altitudes towards water. Rapid and concentrated urbanisation brought problems of expanded demands for drinking supplies, waste management and disease. The strategy of using water from local streams, springs and village wells collapsed under the onslaughts of rising urban demands and pollution due to poor waste disposal practices. Expanding travel (railways. and steamships) aided the spread of disease. In England. public health crises peaks, related to water-borne typhoid and the three major cholera outbreaks occurred in the late eighteenth and early nineteenth century respectively. Technological, engineering and institutional responses were successful in solving the public health problem. it is generally accepted that the putting of water into pipe networks both for a clean drinking supply, as well as using it as a transport medium for removal of human and other wastes, played a significant role in towering death rates due to waterborne diseases such as cholera and typhoid towards the end of the nineteenth century. Today, similar principles apply. A recent World Bank report Indicates that there can be upto 76％ reduction in illness when major water and sanitation improvements occur in developing countries. Water management, technology and thinking in Australia were relatively stable in the twentieth century up to the mid to late 1970s. Groundwater sources were investigated and developed for towns and agriculture. Dams were built, and pipe networks extended both for supply and waste water management. The management paradigms in Australia were essentially extensions of European strategies with the minor adaptions due to climate and hydrogeology. During the 1970s and 1980s in Australia, it was realised increasingly that a knowledge of groundwater and hydrogeological processes were critical to pollution prevention, the development of sound waste management and the problems of salinity. Many millions of dollars have been both saved and generated as a consequence. This is especially in relation to domestic waste management and the disposal of aluminium refinery waste in New South Wales. Major institutional changes in public sector water management are occurring in Australia. Upheveals and change have now reached ail states in Australia with various approaches being followed. Market thinking, corporatisation, privatisation, internationalisation, downsizing and environmental pressures are all playing their role in this paradigm shift. One casualty of this turmoil is the progressive erosion of the public sector skillbase and this may become a serious issue should a public health crisis occur such as a water borne disease. Such crises have arisen over recent times. A complete rethink of the urban water cycle is going on right now in Australia both at the State and Federal level. We are on the threshold of significant change in how we use and manage water, both as a supply and a waste transporter in Urban environments especially. Substantial replacement of the pipe system will be needed in 25 to 30 years time and this will cost billions of dollars. The competition for water between imgation needs and environmental requirements in Australia and overseas will continue to be an issue in rural areas. This will be especially heightened by the rising demand for irrigation produced food as the world's population grows. Rapid urbanisation and industrialisation in the emerging S.E Asian countries are currently producing considerable demands for water management skills and Infrastructure development. This trend e expected to grow. There are also severe water shortages in the Middle East to such an extent that wars may be fought over water issues. Environmental public health crises and shortages will help drive the trends.

• Journal of Periodontal and Implant Science
• /
• v.30 no.4
• /
• pp.851-870
• /
• 2000

The major goals of periodontal therapy is the functional regeneration of periodontal supporting structures already destructed by periodontal disease as well as the reduction of signs and symptoms of progressive periodontal disease. There have been many efforts to develop materials and therapeutic methods to promote periodontal wound healing. There have been increasing interest on the chitosan made by chitin. Chitin is second only to cellulose as the most abundant natural biopolymer. It is a structural component of the exoskeleton of invertebrates(e.g., shrimp, crabs, lobsters), of the cell wall of fungi, and of the cuticle of insects. Chitosan is a derivative of chitin made by deacetylation of side chains. Many experiments using chitosan in various animal models have proven its beneficial effects. The aim of this study is to evaluate the osteogenesis of chitosan on the calvarial critical size defect in Sprague Dawley rats. An 8 mm surgical defect was produced with a trephine bur in the area of the midsagittal suture. The rats were divided into two groups: Untreated control group versus experimental group with 50mg of soluble chitosan gel. The animals were sacrificed at 2, 4 and 8 weeks after surgical procedure. The specimens were examined by histologic, histomorphometric and radiodensitometric analyses. The results are as follows: 1. The length of newly formed bone in the defects was $102.91{\pm}25.46{\mu}m$, $219.46{\pm}97.81{\mu}m$ at the 2 weeks, $130.95{\pm}39.24{\mu}m$, $212.39{\pm}89.22{\mu}m$ at the 4 weeks, $181.53{\pm}76.35{\mu}m$ and $257.12{\pm}51.22{\mu}m$ at the 8 weeks in the control group and experimental group respectively. At all periods, the means of experimental group was greater than those of control group. But, there was no statistically significant difference between the two groups. 2. The area of newly formed bone in the defects was $2962.06{\pm}1284.48{\mu}m^2$, $5194.88{\pm}1247.88{\mu}m^2$ at the 2 weeks, $5103.25{\pm}1375.88{\mu}m^2$, $7751.43{\pm}2228.20{\mu}m^2$ at the 4 weeks and $8046.20{\pm}818.99{\mu}m^2$, $15578.57{\pm}5606.55{\mu}m^2$ at the 8 weeks in the control group and experimental group respectively. At all periods, the means of experimental group was greater than those of control group. The experimental group showed statistically significant difference to the control group at the 2 and 8 weeks. 3. The density of newly formed bone in the defects was $14.26{\pm}6.33%$, $27.91{\pm}6.65%$ at the 2 weeks, $20.06{\pm}9.07%$, $27.86{\pm}8.20%$ at the 4 weeks and $22.99{\pm}3.76%$, $32.17{\pm}6.38%$ at the 8 weeks in the control group and experimental group respectively. At all periods, the means of experimental group was greater than those of control group. The experimental group showed statistically significant difference to the control group at the 2 and 8 weeks. These results suggest that the use of chitosan on the calvarial defects in rats has significant effect on the regeneration of bone tissue in itself