• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2004년도 유체기계 연구개발 발표회 논문집
• /
• pp.572-577
• /
• 2004

This paper presents numerical study on the performance improvement of the sirocco fan in a range hood. The performance of sirocco fan means a higher flowrate, a higher static pressure and a lower required motor power in a fixed geometry constraint. Various impeller geometric parameters, such as blade profile, blade diameter, blade thickness profile and blade exit angle, were investigated by numerically and the results were compared with each other to know the effects on the performance. In this approach, the volute geometry were fixed with the original shape. The numerical results show that the blade profile with airfoil shape and small exit blade thickness increases the performance. The blade exit angle shows optimum angle within a varied range. The efficiency of the optimized exit angle was about $10\%$ higher than the base blade exit angle and the static pressure was about $28\%$ higher at the flow coefficient 0.22.

• 한국자동차공학회논문집
• /
• 제24권2호
• /
• pp.169-182
• /
• 2016

This paper is the third investigation on the evaluation methods of flow characteristics in a steady flow bench. In the previous works, several assumptions used in the steady flow bench were examined and the flow characteristics were estimated both by the conventional impulse swirl meter and a particle image velocimetry at 1.75B position. From these works, it was concluded that the assumption of the solid rotation might cause serious problems and both of the eccentricity and the velocity profile distort the flow characteristics when using the ISM at 1.75B plane. Therefore, the understanding of the detail velocity profiles is very important to keep discussing the issues about the steady flow evaluation method. For this purpose, the planar velocity profiles were measure at 1.75B position by particle image velocimetry and the characteristics were examined according to the valve angles and lifts. The results show that the planar velocity profiles of 11, 16, $21^{\circ}$ valve angle heads according to the lift are similar to each other, however, that of $26^{\circ}$ angle is an exceptional case in the all aspects. In addition, the swirl behaviors are not apparent up to 6~8 mm lift under the $21^{\circ}$ angle and somewhat arranged motions are observed over the whole plane near the highest lift. At this point, the narrower the angle, the lower the lift at which the swirl motions become clear. On the other hands, when the angle is $26^{\circ}$, the center of swirl is always farthest from the cylinder center and only the indistinct swirl is observed even if at the highest lift. Also, all the swirl centers are quite apart from the cylinder center so that the effect of eccentricity may not be negligible at 1.75B regardless the valve angle. Related to the tangential velocity along with the radial direction, the bands of the velocity distribution are very wide and the mean velocities of cylinder center basis are lower than the velocity which is assumed in the ISM evaluation. Lastly, the mean tangential velocity profiles of swirl center basis are sometimes higher than that of ISM-assumed up to 0.6 non-dimensional distance less than 6mm lift, however, as the lift increases the profiles are different according to the angles and profile $11^{\circ}$ is the most closed to the ideal profile. Consequently, the real velocity profile is far from the assumption of ISM evaluation.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1998년도 추계학술대회 논문집
• /
• pp.198-203
• /
• 1998

To acquire the high precision of profile for standard electrode of loss angle, it is needed ultraprecision machining technology like MEAP(Magnetic Electronic Abrasive Polishing) and the very high profile measurement technology which can measure a micro unit about the workpiece. So, in this paper, it was developed the measurement system of precision of profile using non-contactable sensor that was approximate sensor of capacitance type, because that is better than others in the electrical characteristics. And standard electrode of loss angle was machined by the MEAP machining technology. In this study, it was development of precision measurement system. This system could be used measure the workpiece of roundness and straightness much more precise and faster than general mechanical measurement system done before. And it could be helped to minimize machining time and planning by very fast and precise measurement about the workpiece.

• Tribology and Lubricants
• /
• 제5권2호
• /
• pp.107-112
• /
• 1989

This paper deals with strength analysis of tooth and method of manufacture of external tooth profile in harmonic drive. From the calculation of load imposed on the contact teeth, moximum contact stress is investigated to design the addendum modification coefficient. New tooth profile of the external gear is generated according to the law of gearing, assuming that internal gear has involute tooth profile. External tooth profile can't be manufactured by conventional exclusive tools which have pressure angle of 20$\circ$. The method to design cutter tooth profile is presented.

• 대한치과교정학회지
• /
• 제27권5호
• /
• pp.723-732
• /
• 1997

본 연구의 목적은 악안면유형에 따라 측모 연조직 양상에 차이가 있는지를 알아보고자 17세 이상의 연령을 가진 다양한 수직적 양상을 보이는 II급 및 III급 남,녀 79명을 선택하여 각 계측치를 계측하고 통계 처리하여 다음과 같은 결과를 얻었다. 1. Nasolabial angle, interlabial angle, lower lip angle, mentolabial angle, symphyseal angle이 골격성 II급군과 III급군간에 유의한 차이를 보였고, nasofrontal angle, upper lip angle, mentolabial angle, symphyseal angle이 high angle군과 low angle군간에 유의한 차이를 보였다. 2. 악골의 시상적관계를 나타내는 ANB값이 연조직의 nasolabial angle, symphyseal angle, interlabial angle과 정상관 관계를 보였고, lower lip angle과는 역상관 관계를 보였다. 3. 악골의 수직적관계를 나타내는 SN-GoMe값은 연조직의 mentolabial angle, symphyseal angle, nasofrontal angle, upper lip angle과 정상관 관계를 보였다. 4. 골격성 III급군에 비해 II급군에서 SN-GoMe값에 따른 측모연조직 양상의 차이가 현저하였다.

• 한국태양에너지학회 논문집
• /
• 제31권6호
• /
• pp.111-124
• /
• 2011

The objective of this study is to develop the blind control strategy and method which reduce negative effect of incoming daylight on visual comfort of occupants, minimize psychological anxieties caused by frequent motions of a blind, and maximize positive effect of incoming daylight by opening/closing of a blind. In previous researches on blind controls, major problem is that the time interval and amount of blind movement do not meet the control objective at the inflected zone of solar profile curve. To overcome these limitations revealed in theprevious researches, following tasks were performed in this study. i)To establish the control objective to accomplish the goal of this study. ii)To develop the control methods and algorithms which prevent glare on the work-plane at any time and which control the time interval and amount of blind movement to follow the control objective at various solar profile angle curves. This study proposed the control strategy and method that define the base control section implying the inflection point within the control objective zone and subsequently, divide the control sections for the residual time zones. The proposed strategy and method are found to increase the incoming daylight and solar irradiation by 0 to 15 %.

• 대한기계학회논문집
• /
• 제11권2호
• /
• pp.296-303
• /
• 1987

본 논문에서는 동력전달용 기어에 주로 쓰이는 물림률 1.3 이상일 때, 치면접 촉응력과 공칭굽힘응력이 작게되는 풀림각 1˚로 고정하여 잇수 30∼100개 압력각 14˚∼30˚의 범위에서 최소 원호반경식과 치형 조건을 만족하는 최대 원호반경식에 대하여 고찰하였다.

• 한국안전학회지
• /
• 제23권4호
• /
• pp.13-18
• /
• 2008

This study deals with finish roll forming by forced displacement can be conceived as a method of eliminating errors in conventional form rolling under constant loads. This method produces a high-precision tooth profile by low-speed form rolling when a high rigid screw or cam is used at the pressurized section. Tooth profile is decided in the beginning of roll forming and ${\delta}_{max}$ mainly increases if the number of roll forming process is increased. Gear class is improved by one or two class after roll forming if the gear has convex type error and pressure angle error in KS 4 class. If the gear have concave type error and pressure angle error and pressure angle error, gear class is not improved in theory, but improved a little in practice. In the finishing roll forming, it inevitably yields both the concaving of tooth profile and plastic deflection of addendum of teeth. Experiments show that the concaving and the plastic deflection are successfully reduced, the accuracy of tooth profile reaches to KS 0 class.

• Journal of Welding and Joining
• /
• 제16권4호
• /
• pp.109-116
• /
• 1998

The three-dimensional profile of a solder fillet is predicted by minimizing the surface tension and gravity energies of the solder joint using finite element modeling. Geometric complexity stemming from the inclined plane of the gullwing lead is resolved by employing three element types. These element types are used to describe the joint profile formed on the vertical, inclined and interfacial planes. The predicted solder joint profiles show good agreements with the experimental data provided that the solder volume is adjusted considering the wicking effects. Effects of the pad length, inclined lead angle and solder volume on joint profiles are also investigated.

• 한국전자파학회논문지
• /
• 제13권8호
• /
• pp.777-782
• /
• 2002

일반적인 시간 영역에서의 레이더 신호들은 표적의 관측각에 민감하게 변화한다. 따라서 대표적인 시간영역 레이더 신호인 1차원 range profile을 이용하여 구분실험을 하는 경우에 있어서 central moments와 PCA를 결합하여 먼저 특성벡터를 추출한 후 clustering 기법에 기반한 subclass concept을 사용하는 구분기를 사용하여 넓은 관측각에서의 표적인식 성능을 향상시킨 결과들을 보여준다.