• 청정기술
• /
• 제21권4호
• /
• pp.217-223
• /
• 2015

본 연구에서는 에탄올-n-헵탄 이성분계 공비 혼합물의 분리를 위해 압력변환 증류공정(pressure-swing distillation, PSD)을 사용하여 전산모사 및 공정 최적화를 진행하였다. 저압-고압 컬럼 배열과 고압-저압 컬럼 배열을 통해 고순도 에탄올과 고순도 n-헵탄을 얻기 위한 압력변환 증류공정을 수행하였다. 전산모사 결과, 저압-고압 컬럼 배열 공정보다 고압-저압 컬럼 배열 공정을 사용할 경우 heat duty 값이 약 5.8% 정도 감소되어 에너지 소모량 면에서 더 경제적임을 확인할 수 있었다.

• 설비공학논문집
• /
• 제7권1호
• /
• pp.120-131
• /
• 1995

Thermodynamic analysis of extraction process from the constant pressure LNG(Liquefied Natural Gas) vessel was performed in this study. LNG was assumed as a binary mixture of 90% methane and 10% ethane by mole fraction. The thermodynamic properties such as temperature, composition, specific volume and the amount of cold energy were predicted during extraction process. Pressure as a parameter ranges from 101.3kPa to 2000kPa. The result shows the peculiar phenomena for the LNG as a mixture. Both vapor and liquid extraction processes were investigated by a computer model. The property changes are negligible in the liquid extraction process. For the vapor extraction process, the temperature in the vessel increases rapidly and the extracted composition of methane decreases rapidly near the end of extracting process. Specific volume of vapor has the maximum and that of liquid has the minimum during the process. When pressure is increased, specific volume of vapor decreases and that of liquid increases. It was found that specific volume of vapor phase had a major effect on the heat absorption at constant pressure during vapor extraction process. If the pressure of the vessel increases, the total cold energy which can be utilized from LNG decreased.

• 한국공작기계학회논문집
• /
• 제11권4호
• /
• pp.44-53
• /
• 2002

Injection molding process factors such as molding temperature, injection pressure, flow rate and flow velocity, must be controlled properly in filling and packing phases in the injection molding process. In this study, effects of these factors on the injection molding were investigated through the flow analysis for the filling and packing phases. Molding troubles like flow mark weld line, sink ma가 short shot and warpage car be caused by these injection molding process factors. Among them the short shot was caused by the fact that the packing pressure could not reach properly to the filling end part in the packing phase and hence the flow rate could not be supplied to the full. In addition as the flow rate for the volumetric shrinkage during the f개zen phase could not be supplied Properly by the packing pressure, the short shot appeared. Here, the volumetric shrinkage reduced with increasing the packing pressure and also the warpage of molded part increased with increasing the packing Pressure.

• 반도체디스플레이기술학회지
• /
• 제8권2호
• /
• pp.15-21
• /
• 2009

Atmospheric pressure plasma equipment was successfully applied to the flip chip BGA manufacturing process to improve the uniformity of flux printing process. The problem was characterized as shrinkage of the printed flux layer due to insufficient surface energy of the flip chip BGA substrate. To improve the hydrophilic characteristics of the flip chip BGA substrate, remote DBD type atmospheric pressure plasma equipment was developed and adapted to the flux print process. The equipment enhanced the surface energy of the substrate to reasonable level and made the flux be distributed over the entire flip chip BGA substrate uniformly. This research was the first adaptation of the atmospheric pressure plasma equipment to the flip chip BGA manufacturing process and a lot of possible applications are supposed to be extended to other PCB manufacturing processes such as organic cleaning, etc.

• 한국기계가공학회지
• /
• 제11권6호
• /
• pp.55-61
• /
• 2012

In this study, it was grasped to the flow characteristics of injection nozzle installed in high pressure holder for improving productivity. Chip curling occurred during cutting process for difficult-to-cut material detracts product qualities and productivity. Among of method preventing the phenomenon, high pressure injecting cutting oil is an alterative. In this study, the optimal nozzle was designed by CFD method and it was conducted to analyse on the effect of high pressure injection on chip shape generated during cutting process and wear of insert by experimental method. As the result, it could be confirmed that high pressure injection is favorable for preventing chip curling and insert from wearing.

• 한국기계가공학회지
• /
• 제19권4호
• /
• pp.36-44
• /
• 2020

This study analyzed the deformation behavior of the high density polyethylene (HDPE) bottle in the blow molding process. We carried out finite element (FE) simulations using ANSYS Polyflow. First, the axisymmetric model was executed by 2D FE-simulation to determine the change of bottle wall thickness during the molding process. Then, the square model of the bottle was executed by 3D FE-simulation to gauge the effects of gas pressure on the change of wall thickness. The experiment results showed that the FE-simulations were able to upgrade the quality of the HDPE bottle in the blow molding process. These results can be used as guidance in adjusting gas pressure, as well as be extended for further study to determine process parameters such as temperatures, forming velocity, parison shape, etc.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 춘계학술대회 논문집
• /
• pp.332-335
• /
• 2007

The superplastic forming (SPF) has been widely used in the automotive and aerospace industry because it has great advantages to produce very light and strong components. Finite element method (FEM) is used to model the process of superplastic forming/diffusion bonding (SPF/DB), to predict the pressure-time curve and to analyze the process parameter. In this study, process design of SPF/DB is carried out a 3-sheet sandwich part. SPF/DB process with pressure control was analyzed by using finite element method. For obtaining proper shape, step-by-step pressurization is proposed. The first step of SPD/DB process is obtained by applying of pressure in patches. From the next step it applied pressure to all regions (between inner sheets, between inner and face sheets). By using the proposed pressurization scheme, deficit in part shape is found to be eliminated.

• Nuclear Engineering and Technology
• /
• 제36권4호
• /
• pp.338-345
• /
• 2004

This study examines the sensitivity of several fabrication parameters for dry process fuel, using a random sampling technique. The in-pile performance of dry process fuel with irradiation was calculated by a modified ELESTRES code, which is the CANDU fuel performance code system. The performance of the fuel rod was then analyzed using a Monte Carlo simulation to obtain the uncertainty of the major outputs, such as the fuel centerline temperature, the fission gas pressure, and the plastic strain. It was proved by statistical analysis that for both the dry process fuel and the $UO_2$ fuel, pellet density is one of the most sensitive parameters, but as for the fission gas pressure, the density of the $UO_2$ fuel exhibits insensitive behavior compared to that of the dry process fuel. The grain size of the dry process fuel is insensitive to the fission gas pressure, while the grain size of the $UO_2$ fuel is correlative to the fission gas pressure. From the calculation with a typical CANDU reactor power envelop, the centerline temperature, fission gas pressure, and plastic strain of the dry process fuel are higher than those of the $UO_2$ fuel.

• 상하수도학회지
• /
• 제29권1호
• /
• pp.133-138
• /
• 2015

Pressure retarded osmosis (PRO) process is one of membrane processes for harvesting renewable energy by using salinity difference between feed and draw solutions. Power is generated by permeation flux multiplied by hydraulic pressure in draw side. Membrane fouling phenomena in PRO process is presumed to be less sever, but it is inevitable. Membrane fouling in PRO process decreases water permeation through membrane, resulting in significant power production decline. This study intended to investigate the effect of hydraulic pressure in PRO process on alginate induced organic fouling as high and low hydraulic pressures (6.5 bar and 12 bar) were applied for 24 h under the same initial water flux. In addition, organic fouling in draw side from the presence of foulant (sodium alginate) in draw solution was examined. As major results, hydraulic pressure was found to be not a significant factor affecting in PRO organic fouling as long as the same initial water flux is maintained, inidicating that operating PRO process with high hydraulic pressure for efficient energy harvesting will not cause severe organic fouling. In addition, flux decline was negligible from the presence of organic foulant in draw side.

• Korean Chemical Engineering Research
• /
• 제62권2호
• /
• pp.163-172
• /
• 2024

본 연구에서는 이산화탄소를 배출하지 않고 수소를 운반할 수 있는 그린 암모니아 공정의 효율적인 설계를 위해 암모니아 액화 시나리오를 다르게 설계하고 이에 대한 경제성 및 환경 영향도 평가를 수행하였다. 순도 99.9 mol%의 148 kmol/hr 액화 암모니아를 생산물로 얻는 것을 목표로 설정하였고 후처리 단계에서 냉각단계 전 기-액분리를 통해 일정량의 액화 암모니아를 분리하고 고압에서 냉각하는 고압 냉각 공정과 기-액분리 과정 없이 바로 감압 후 냉각하여 기-액분리를 시켜 최종생산물을 얻는 저압 냉각 공정의 두 가지 케이스를 설정했다. 이에 대한 타당성 평가를 위해 Aspen Plus를 활용한 시뮬레이션을 수행하였다. 고압 냉각 공정은 많은 기-액분리 공정과 열교환기를 사용하여 초기장치 비용이 부담되지만 상대적으로 총 유틸리티 비용이 91.03 $/hr, duty가 2.81 Gcal/hr 낮아 유지비용이 적게 든다. 저압 냉각 공정은 초기 장치 비용이 낮고 운전이 용이하지만 급격한 압력 강하로 운전이 불안정한 것을 확인 하였다. 환경 영향도 평가 결과 고압 냉각 공정이 저압 냉각 공정보다 전력 사용량을 기준으로 산출한 이산화탄소 환산톤 배출 계수가 0.83 tCO₂eq 더 낮아 환경친화적 임을 확인할 수 있었다. 본 연구 결과를 통해 향후 그린 암모니아 합성 공정에서 여러 상황에 적절한 설계안을 도출할 수 있는 데이터베이스를 확보할 수 있다.