• 대한의용생체공학회:의공학회지
• /
• 제6권2호
• /
• pp.1-8
• /
• 1985

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70$\pm$1.32mmHg/min)compared to CF dialyzers(4.32$\pm$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500, 550, 570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500, 550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100, 300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3, 000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.SpO2 with Plethysmograph.

• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 1993년도 한국우주과학회보 제2권2호
• /
• pp.17-17
• /
• 1993

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70${\pm}$1.32mmHg/min)compared to CF dialyzers(4.32${\pm}$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500,550,570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500,550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100,300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3,000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.

• 대한지리학회지
• /
• 제30권1호
• /
• pp.68-92
• /
• 1995

소매업은 경제, 사회, 문화, 정치를 배경으로 소비자의 요구에 부응하며 발전해 가 기 때문에 지역구조의 이해라는 측면에서 증요한 연구 주제이다. 또한 소매업은 일상생활을 영위하기 위한 기본적인 기능이므로, 이에 대한 이해는 삶의 질 향상이라는 측면에서도 중 요하다. 최근, 우리나라는 주민소득의 향상과 그에 따른 수요의 다양화, 개성화, 그리고 정보 화 사회로의 이행, 대기업 및 외국유통업의 참여, 정부의 유통산업 근대화 작업 등 소매업 환경의 변화와 함께 소매업이 크게 변화하고 있다. 따라서 미래의 변화 예측과 바람직한 발 전 방향이 제시되어야 함에도 불구하고, 이에 대한 연구가 미흡하다. 이에 광주시를 연구대 상지역으로 선정하여, 소매업의 입지와 그에 대한 주민의 이용 행태, 그리고 주민의 바람직 한 이용방안을 분석하였다. 이는 입지행태라는 순수한 학문적기여 뿐 아니라, 지역의 효율성 과 평등성의 실현이라는 응용면에서도 중요한 의의를 지닌다.

• 한국축산시설환경학회지
• /
• 제18권3호
• /
• pp.145-150
• /
• 2012

한우 깔짚 더미에서 배출되는 $CH_4$의 일별 배출량은 측정 시작일의 273.013 ${\mu}g\;m^{-2}\;s^{-1}$ (SE : ${\pm}1.047{\mu}g\;m^{-2}s^{-1}$)을 최대로 하여 점차 감소하여 측정 마지막 일에는 2.309 ${\mu}g\;m^{-2}\;s^{-1}$ (SE : ${\pm}0.061{\mu}g\;m^{-2}\;s^{-1}$)이었다. $N_2O$의 일별 배출량은 $CH_4$의 배출량과 달리 측정 시작일에는 0.267 ${\mu}g\;m^{-2}\;s^{-1}$ (SE : ${\pm}0.018{\mu}g\;m^{-2}\;s^{-1}$)로 미미하였으나 시간이 지남에 따라 지수적으로 증가하여 시험 시작 후 43일째에 3.596 ${\mu}g\;m^{-2}\;s^{-1}$ (SE : ${\pm}0.454{\mu}g\;m^{-2}\;s^{-1}$)로 최대를 기록한 후 서서히 감소하여 마지막 일에는 1.888 ${\mu}g\;m^{-2}\;s^{-1}$ (SE : ${\pm}0.012{\mu}g\;m^{-2}\;s^{-1}$) 이었다. 지구온난화지수를 이용한 $CH_4$과 $N_2O$ 배출량을 $CO_2$-eq로 환산했을 때, 시험첫 날 $CH_4$에 의한 $CO_2$-eq가 전체 환산량의 약 99%였다. 이후 $CH_4$의 배출량이 감소하고 $N_2O$의 배출이 증가하면서 34일 째에 $CH_4$과 $N_2O$에 의한 CO-eq 비율이 50:50이 되었으며 이후 $N_2O$의 영향이 더 컸다. $CH_4$과 $N_2O$의 배출량 변동성을 보기 위해 $CH_4$과 $N_2O$의 일 평균 배출량에 대한 일별 표준오차의 비율을 계산하였다. $CH_4$의 경우 그 비율이 11일째까지는 1.0% 이하였으나 시간이 지날수록 증가하여 57일 후에는 10.9%까지 증가하였다. $N_2O$의 경우 $CH_4$에 비해 그 비율이 컸는데 (0.4%~51.0%), $CH_4$의 경우와 달리 초기에 높았으며 시간이 지날수록 줄었다. $CH_4$과 $N_2O$의 생성이 활발할 경우 일 평균 배출량에 대한 일별 표준오차의 비율이 적으나 그렇지 않을 경우 비율이 높아졌는데 이는 배출장소의 비 균질성에 기인한다고 볼 수 있다. 따라서 퇴비화 과정의 온실가스 배출량을 줄이기 위해서는 $CH_4$ 감소를 위해 초기 공기 공급을 늘리며, 교반 등을 통해 비균질성을 감소시켜야 한다.

• 지능정보연구
• /
• 제26권3호
• /
• pp.91-108
• /
• 2020

박지성 선수의 2005년 맨체스터 유나이티드 FC 입단 이후로, 국내에서 프로축구 유니폼 시장이 본격적으로 성장하기 시작했다. 이후, 국내 선수들의 해외 리그에서 활약이 계속되면서 국내에서도 잉글랜드 프리미어리그에 대한 대중의 관심이 지속되고 있다. 이러한 시점에서 본 연구는 국내 프로축구 팬들의 유니폼 소비에 전반적인 소비자 인식을 알아보고, 선수의 영입에 따른 소비자 인식 변화를 비교하고자 했다. EPL의 토트넘에서 활동하고 있는 손흥민 선수의 영입 전후를 중심으로 소셜 미디어에 나타난 프로축구 팬들의 소비자 인식과 구매 요인을 알아보았다. 'EPL 유니폼'을 키워드로, 국내 포털사이트와 소셜 미디어의 게시글을 수집하고, 텍스트 마이닝, SNA, 회귀분석을 사용하여 분석했다. 연구 결과, 첫째, 선수의 소속 팀, 실적, 포지션과 구단의 실적, 순위, 리그의 우승 여부가 프로축구 유니폼의 구매와 탐색에 있어 주요 요인으로 확인되었다. 가격, 디자인, 사이즈, 로고 등과 같은 항목보다 유니폼의 형태, 마킹, 정품 여부, 스폰서와 더 중요하게 작용하고 있었다. 둘째, 구조적 등위성 분석과 군집분석을 통해 국내 프로축구 팬들 사이에서 유니폼과 관련되어 언급되고 있는 주요 주제를 알아본 결과, EPL에 소속된 구단과 유명 선수들이 가장 핵심적인 주제로 나타났다. 셋째, 프로축구 유니폼에 대한 시기별 주제는 월드컵과 EPL 리그에 대한 관심에서 EPL에서 활동하는 다양한 국내외 선수들에 대한 관심으로, 2015년 이후에는 유니폼 자체에 대한 것으로 주제가 변화했다. 이를 통해, 선수들의 이적에 따라 선수가 소속된 해당 구단의 유니폼이 관심을 받고 있음을 알 수 있었다. 넷째, 남녀 소비자 모두 손흥민에 대한 관심이 증가함에 따라서 토트넘이 소속된 리그인 EPL에 대한 관심도 증가하는 것으로 나타났다. 여성의 경우 손흥민에 대한 관심이 증가함에 따라 축구 유니폼에 대해서도 관심을 가지는 것으로 나타난 반면, 남성의 경우 손흥민 선수에 대한 관심과 축구 유니폼에 대한 관심 사이의 관계가 유의하게 나타나지 않았다. 각 구단은 선수와 구단의 성적과 이미지 관리, 스폰서 브랜드 관리에 집중하고, 선수의 이적이 결정되면 선수의 자국에 해당 물량의 공급을 늘리며, 인기를 끌고 있는 선수의 등번호가 부착된 유니폼의 경우에는 여성을 위한 다양한 사이즈를 제공해야 할 필요가 있다.

• 지능정보연구
• /
• 제24권4호
• /
• pp.219-240
• /
• 2018

감성사전은 감성 어휘에 대한 사전으로 감성 분석(Sentiment Analysis)을 위한 기초 자료로 활용된다. 이와 같은 감성사전을 구성하는 감성 어휘는 특정 도메인에 따라 감성의 종류나 정도가 달라질 수 있다. 예를 들면, '슬프다'라는 감성 어휘는 일반적으로 부정의 의미를 나타내지만 영화 도메인에 적용되었을 경우 부정의 의미를 나타내지 않는다. 그렇기 때문에 정확한 감성 분석을 수행하기 위해서는 특정 도메인에 알맞은 감성사전을 구축하는 것이 중요하다. 최근 특정 도메인에 알맞은 감성사전을 구축하기 위해 범용 감성 사전인 오픈한글, SentiWordNet 등을 활용한 연구가 진행되어 왔으나 오픈한글은 현재 서비스가 종료되어 활용이 불가능하며, SentiWordNet은 번역 간에 한국 감성 어휘들의 특징이 잘 반영되지 않는다는 문제점으로 인해 특정 도메인의 감성사전 구축을 위한 기초 자료로써 제약이 존재한다. 이 논문에서는 기존의 범용 감성사전의 문제점을 해결하기 위해 한국어 기반의 새로운 범용 감성사전을 구축하고 이를 KNU 한국어 감성사전이라 명명한다. KNU 한국어 감성사전은 표준국어대사전의 뜻풀이의 감성을 Bi-LSTM을 활용하여 89.45%의 정확도로 분류하였으며 긍정으로 분류된 뜻풀이에서는 긍정에 대한 감성 어휘를, 부정으로 분류된 뜻풀이에서는 부정에 대한 감성 어휘를 1-gram, 2-gram, 어구 그리고 문형 등 다양한 형태로 추출한다. 또한 다양한 외부 소스(SentiWordNet, SenticNet, 감정동사, 감성사전0603)를 활용하여 감성 어휘를 확장하였으며 온라인 텍스트 데이터에서 사용되는 신조어, 이모티콘에 대한 감성 어휘도 포함하고 있다. 이 논문에서 구축한 KNU 한국어 감성사전은 특정 도메인에 영향을 받지 않는 14,843개의 감성 어휘로 구성되어 있으며 특정 도메인에 대한 감성사전을 효율적이고 빠르게 구축하기 위한 기초 자료로 활용될 수 있다. 또한 딥러닝의 성능을 높이기 위한 입력 자질로써 활용될 수 있으며, 기본적인 감성 분석의 수행이나 기계 학습을 위한 대량의 학습 데이터 세트를 빠르게 구축에 활용될 수 있다.

• 헤리티지:역사와 과학
• /
• 제45권4호
• /
• pp.54-73
• /
• 2012

최근 북방유목민족인 사르마티아에 관한 고고학적 자료들이 증가하면서 사르마티아인들의 활동 양상과 그 실체들이 조금씩 규명되고 있다. 이 글에서는 사르마티아인들의 동서 교역의 활동 양상을 사르마티아식 검집의 확산 지역 중심으로 살펴보았다. 사르마티아인들의 검은 스키타이나 페르시아인들이 사용한 아키나케스(Akinakes)의 계보를 잇는 것이지만 손잡이나 패용 방식에서 손쉽게 칼을 뺄 수 있도록 변화되었다. 즉 양 측면에 달린 4개 돌기에 끈으로 연결한 검집을 허벅지에 부착시키는 패용 구조로 변한 것이다. 사르마티아식 검은 기원전 5세기 파지리크시기 알타이 지역에서 처음 등장한 이래 사르마티아인들의 활동 중심지인 남시베리아, 박트리아, 파르티아, 로마로 확산되었다. 이 글에서는 동서 교섭의 요충지인 박트리아지역에 속하는 아프가니스탄 틸랴 테페 4호묘에서 출토된 검집에 관심을 두었다. 사르마티아식 검을 패용한 채 매장되었던 틸랴 테페 4호묘의 묘주는 당시 쿠샨왕조의 지배하에 있었던 박트리아에서 상당한 위치의 인물로 파악된다. 묘주가 2자루의 사르마티아식 검을 패용하고 있었던 것은 박트리아에 사르마티아의 영향이 상당이 수용된 사실을 의미한다. 사르마티아인들이 동서교섭에서 중요한 역할을 담당할 수 있었던 배경에는 중국산 물자를 실크로드에 공급하였던 이들의 역할과도 관련이 있다. 이에 사르마티아인들이 활동한 북방 초원 루트에 중국 한대 동경, 메론형 구슬, 수정구슬 등의 장식구슬, 금환연접구슬 등 중국 특히 비단이 생산되었던 남중국의 공예품들이 출토되는 경위에 관심을 가졌다. 모자이크 구슬은 당시 남중국 그리고 사르마티아와의 관계에 의한 것으로 살펴보았다. 거리적으로 먼 사르마티아와 남중국이 교섭할 수 있었던 중간 매체로는 흉노가 주목된다. 이와 관련하여 흉노의 유적에서 남중국에 가장 많은 분포를 보이는 금환연접구슬이 발견되는 점을 참고하였다. 남인도와 동남아시아에서 유행한 금환연접구슬이나 모자이크구슬이 아프카니스탄의 틸랴 테페 유적에는 없는 반면 같은 초원길로 연결되는 사르마티아 유적이나 흉노의 몽골 유적에서 등장하는 점이 흥미로운 것이다. 이는 남중국과 사르마티아, 흉노와의 연결 루트를 상정하게 한다. 한편 사르마티아인들의 중심연대인 기원전 2세기에서 기원후 2세기 사이 초원루트와 남중국을 잇는 교통로로는 운남에서 미안마를 지나 파키스탄, 아프가니스탄을 지나 인도 동부로 들어가는 서남실크로드로 판단된다. 1세기 동서교섭의 루트에는 북방 초원 루트, 남해 루트, 오아시스 루트 등 다양한 루트가 존재한다. 이들 루트들은 운반, 집산되는 물자의 특성이나 당시 정치적 관계에 의해 다양하게 사용되고 형성되었다. 이 글에서는 인도와 중앙아시아, 그리고 남중국을 잇는 최단거리의 길인 서남루트가 북방 유목민들인 사르마티아인들에 의해 사용되고 개척된 상황을 살펴본 것이다.

• 공연문화연구
• /
• 제22호
• /
• pp.185-221
• /
• 2011

본 연구는 해외교포사회에 북한춤이 전파되는 과정과 그 발전양상을 살펴보는데 목적을 둔 것으로, 해외에 거주하는 민족집단으로서의 재외동포들의 무용문화, 특히 재중, 재일조선인들의 무용문화에 대한 관심과 연구의 필요성을 생각해보았다. 문헌연구 중심으로 살펴본 논점의 결과, 재일조선인사회와 중국조선족자치구의 무용문화의 출발점엔 공통적으로 최승희춤이 있었으며, 두 민족집단은 최승희로부터 직접·간접적으로 춤을 배우거나 작품을 전수받았으며, 최승희가 정리한 조선무용기본을 기초훈련으로 하여 무용을 습득했다. 또한 무용전수 및 훈련기관은 재일조선인사회의 경우 북한의 체계와 같이 무용소조를 따로 두고 그곳에서 무용훈련을 통해 재능있는 인재를 배출하여, 전문예술단에서 활동하게 하는 시스템을 유지해 왔다. 이에 반해 중국조선족자치구는 연변대학과 중앙민족대학내에 무용학과가 배치되어 있어 그곳에서 조선춤을 전수 교육함으로써 재능있는 무용인재들을 배출해 왔으며, 한국의 무용교육체계와 유사한 면을 볼 수 있다. 무용기초훈련과 작품의 경향면에서는 재일조선인사회에서는 북한에서 실천하고 있는 무용기초훈련과 기본훈련을 그대로 전수하고 있으며, 작품도 북한춤을 대표하는 명무나 민속무용을 그대로 전수받아 공연하고 있다. 그러나 중국조선족자치구에서는 최승희가 정리한 조선무용의 기초와 작품을 그녀로부터 직접 훈련받거나 전수받았으나, 최승희의 제자들은 그녀가 세운 무용기초를 발전시켜 중국소수민족의 춤기법 등을 접수하면서 중국조선족만의 무용훈련체계를 세워나가면서 한국춤과의 교류도 성사시켜 북한춤보다는 자유롭게 창작성을 가미한 중국조선족 무용문화를 형성하게 되었다. 전수된 시기로 보면, 재일조선인사회는 1960년대부터 시작되어 1970년대에 들어서는 직접적인 평양방문을 통해 전수와 교육을 받았고, 1990년대에는 북한무용가를 직접 일본으로 초청하여 무용기초훈련을 교육받음으로써 북한춤에서 볼 수 있는 스펙터클한 양상을 그대로 재현하고 있다하겠으나, 중국조선족자치구에서는 1950년대에 평양과 북경에서 최승희로부터 직접적인 지도를 받았고, 이후에는 북한무용가들로부터의 직접적인 지도보다는 북한예술단의 중국방문을 계기로 무용영향을 받는 한편, 1990년대 이후부터는 한국춤을 흡수하기 시작하면서 중국조선족만의 색다른 무용문화를 창조해 왔다. 같은 민족이면서도 살아가는 지역과 그 지역을 구성하는 민족집단의 구성체계 및 정치체제에 따라 북한춤의 전수과정 및 발전양상도 유사하지만 각각의 아이덴티티를 보장하는 독자적인 특색을 지닌 무용문화를 형성하며 발전시켜 왔음을 알 수 있으며, 재일조선인사회의 무용문화는 조총련의 통제하 강제적 문화접변에 의한 무용문화의 변동을, 중국조선족자치구의 무용문화는 자발적 문화접변에 의한 자유로운 차용과 발전으로의 변동을 살필 수 있었다.

• 미술자료
• /
• 제96권
• /
• pp.239-260
• /
• 2019

본 논고는 19세기 이후 형성된 서화(書畫)의 유통과 확산의 양상을 당시 활발히 제작된 장식병풍 중 하나인 <백선도(百扇圖)>의 예를 통해 살펴본 글이다. 백선도는 화면에 다양한 형태의 부채를 겹쳐서 배치하고 각각의 선면(扇面) 안에 여러 종류의 화제(畫題)를 그린 것을 말한다. 부채와 선면화(扇面畫)라는 소재는 이전부터 존재하였지만 장식용 회화의 소재로 등장한 것은 19세기 이후로, 호사취미 경향을 반영하여 주로 병풍(屛風)으로 활발히 제작되었다. 지난 2016년 국립중앙박물관 특별전 '미술 속 도시, 도시 속 미술'에서 독일로텐바움세계문화예술박물관 소장 <백선도>가 새로이 소개된 바 있다. 6폭으로 구성된 이 병풍에는 한 폭 당 5개 이상의 다양한 종류의 부채들이 등장하고 각 부채 면에는 단순히 채색한 것 뿐 아니라 다양한 화목(畫目)의 그림들이 남아있다. 무엇보다 이 작품을 주목해야 하는 것은 국립중앙박물관에 동일한 초본(草本)이 전하고 있기 때문이다. 19세기에 들어서면서 이전의 왕실이나 사대부들이 사적인 공간에서 향유하였던 서화(書畫)는 민간으로 확산되었고 시장을 통한 유통의 단계로 넓어졌다. 집안을 꾸미고 장식하는 풍조에 따라 화려한 장식그림들이 선호되었고, 한 폭에 다양한 형태의 화면과 다채로운 畫目(화목)의 그림을 그려 완성하는 백납도병풍 제작이 성행하였다. 로텐바움박물관 소장 한국 컬렉션의 상당수는 독일 주재 조선국 총영사이자 독일의 사업가였던 하인리히 콘스탄틴 에두아르 마이어(Heinrich Constantin Eduard Meyer, 1841~1926)의 수집품이다. 그는 1890년대 후반부터 1905년까지 조선과 독일을 오가며 다양한 유물들을 수집하여 독일에 돌아가 1909년까지 순차적으로 수집품을 로텐바움박물관에 전달하였으며, <백선도>도 그 중 하나이다. 새롭고 장식미가 돋보이는 <백선도>는 조선에 들어와 있던 외국인들의 이목을 집중시키기에 충분했을 것이다. 로텐바움박물관 소장 <백납도>는 제2폭의 뒷면에 "동현(銅峴)"이라는 지명이 적힌 종이조각이 거꾸로 붙어있어 흥미를 끈다. 동현은 지금의 서울 을지로 1가와 을지로2가 사이에 위치했던 곳이며, 조선시대에는 도화서(圖畫署)를 비롯한 혜민서(惠民署)·장악원(掌樂院) 등의 관청과 시전(市廛)이 있어 가내수공업이 성하던 지역이었다. 실제로 1900년대 초 이곳에는 서화를 유통하는 상점들이 자리잡고 있었기 때문에, 마이어가 수집했던 서화들의 구입처가 동현에 위치했었을 가능성은 매우 높다고 하겠다. 로텐바움박물관 소장 <백선도>는 총 6폭의 병풍으로, 1980년대에 한국 서화 소장품들을 수리하는 과정에서 현재의 모습을 갖춘 것으로 보인다. 국립중앙박물관 소장 <백선도 초본>은 1945년부터 1950년 사이 국립민족박물관에 입수된 작품이다. <백선도 초본>은 총 7점으로, 7점 중 6면 화면의 여백에 화면의 순서까지 정해져 있어 본래 총 8폭 병풍용 초본임을 알 수 있다. 한 화면에는 5개 이상의 다양한 접선(摺扇)과 단선(團扇)들이 배열해있는데, 작은 장식에서부터 부챗살의 문양까지 초본부터 사실적으로 묘사되었음을 볼 수 있다. 여기에 '석간주(石間朱)', '홍(紅)', '묵(墨)', '청(靑)' 등과 같이 부채에 들어갈 색 대부분을 지정하고, 빈 부채에는 '유(油)'라고 적거나 비워두었으며 이 중 10개의 부채에는 화훼초충도(花卉草蟲圖)나 고사인물도의 밑그림이 남아있다. 이를 실제 로텐바움박물관 소장 <백선도>와 비교하면 화면의 크기와 비례까지 정확하게 일치하고 있어, 초본의 매뉴얼을 그대로 따르고 있음을 보여준다. 이 작품의 펼쳐진 부채 면에는 산수, 고사인물, 화조, 영모, 초충, 어해 등 다양한 장르의 그림이 그려져 있는데 화접도(花蝶圖)나 어해도(魚蟹圖) 등은 19세기 유행하였던 소재로 당시 화단의 경향을 잘 보여준다. 이 작품에서 주목할 것은 김홍도(金弘道)의 전형적인 화풍을 연상시키는 장면들이 다수 포함되어 있다는 점이다. 이는 지금까지 알려진 백선도나 백납도에서는 찾아보기 어려운 특징이다. 서원아집도(西園雅集圖)는 상대적으로 제한된 작은 화면에 그려야 하는 백납도나 백선도의 특성상 잘 다루지 않는 소재로, 국립중앙박물관 소장 김홍도의 <서원아집도>병풍과 화면의 구성이나 화풍 모두 매우 흡사하다. 더구나 <백선도>병풍의 몇몇 장면은 김홍도의 작품 중에서도 1796년작 《병진년화첩(丙辰年畫帖)》과 유사한 화면들을 다수 발견할 수 있어 흥미롭다. <사인암(舍人巖)>과 흡사한 산수도(山水圖)를 비롯하여 <서원아집도>, <쌍치도(雙雉圖)> 등에서 김홍도 화풍을 연상시킨다. 따라서 부채 속 그림을 그린 인물은 김홍도 화풍의 영향을 받은 직업화가일 것으로 보이며, 작가는 《병진년화첩》을 직접 감상한 적이 있거나, 서화시장에 《병진년화첩》을 베껴 그린 부본(副本)이 유통되었을 가능성이 매우 높다. 현재까지 알려진 병풍으로 된 백선도는 10점 내외인 것으로 파악되며, 이 작품들을 비교해보면 화면의 구성이 부채 1개 정도 차이가 있거나 비례와 좌우가 바뀌었을 뿐 화면구성이 매우 유사함을 찾아볼 수 있다. 이처럼 일정한 패턴의 화면구성은 같은 시기 민간에서 성행한 책가도(冊架圖)에서도 찾아볼 수 있는 특징으로, 19세기 서화의 수요층이 넓어짐에 따라 세밀한 표현과 화려한 장식성이 요구되는 회화들의 대량 제작을 위한 초본이 존재했음을 보여준다. 특히 도안이 복잡하여 범본이 필요한 곽분양행락도나 요지연도, 백동자도, 해학반도도 등의 규모가 큰 장식병풍에서 적극 활용되었으며, 실제 남아있는 작품에서 몇 가지의 도상들이 반복하여 등장하고 있어 초본을 참고했던 흔적을 찾아볼 수 있다. 시장의 수요에 맞추어 대량 제작할 수 있는 초본 활용이 성행했던 당시의 경향은 화면을 다채로운 부채들로 채우고 그 부채 면에 각기 다른 그림을 그려야하는 백선도 제작에 있어서도, 초본을 요긴하게 사용했음을 보여준다. 더구나 테두리를 그은 후 다양한 화목의 그림을 담는 백납도에 비해 백선도는 다양한 형태의 부채들을 먼저 그려야하는 공정을 거쳐야 했기 때문에, 대량 제작이 어렵고 그만큼 남아있는 작품이 상대적으로 적은 원인으로 생각된다. 이처럼 로텐바움박물관 소장 <백선도> 병풍과 국립중앙박물관 <백선도 초본>은 새로운 화풍이 수용되어 시도되었던 조선 말기 화단의 경향을 잘 보여주는 예라 하겠다. 다수의 백선도들이 박기준의 작품과 유사한 화풍과 화면 구성 보이는 것에 비해, 김홍도의 영향이 분명히 드러나는 매우 이례적인 예라는 점에서 앞으로도 더욱 심층적인 분석이 요구되는 작품이다.

• 한국잠사곤충학회지
• /
• 제25권2호
• /
• pp.1-31
• /
• 1984

가잠에 있어서 피해가 많은 전염성 연화병(Flacherie Virus; FV)과 농핵병 바이러스(Densonucleosis virus; DNV)의 증식에 관한 연구를 행하기 위하여 서당밀도 구배 초원심분리법에 의한 양바이러스의 정제 및 전자현미경에 의한 관찰, 바이러스 감염잠의 중장과 체액에서의 핵산과 단백질의 변동 및 감염중장 피막세포의 전자현미경에 의한 병리조직학적 관찰 등, 일연의 조사를 통하여 다음과 같은 연구결과를 얻었다. 1. 서당밀도구배에 의한 초원심분리법을 이용하여 FV 및 DNV를 분획한 결과, base line이 낮고 좌우상칭의 단일 peak를 나타내는 전형적인 바이러스 분획을 얻었으며, 또한 이들 바이러스의 negative 염색에 의한 전자현미경 관찰에서 FV는 27nm, DNV는 21nm의 균일한 구형입자임이 확인되었다. 2. 두 바이러스 감염잠의 체중은 바이러스 접종 6일 후부터, 중장중은 바이러스 접종 3일 후부터 건전잠에 비해 뚜렷한 감소를 나타냈다. 3. DNA의 양적 변화는 FV 및 DNV 감염잠에서 공히 중장에서는 전기간을 통해 건전잠에서 보다 높았고, 체액에서는 바이러스 접종 초ㆍ중기에는 큰 변화가 없고 바이러스 접종 7일 이후에는 건전잠에서 보다 훨씬 낮았다. 4. RNA의 양적 변화는 FV 및 DNV 감염잠에서 다같이 바이러스 접종 초기에 중장에서는 건전잠에 비해 높았고, 체액에서는 건전잠에 비해 매우 낮았으나, 바이러스 접종 말기에는 중장 및 체액의 경우 공히 건전잠에서 보다 현저히 낮았으며 그 정도는 DNV 감염잠에서 더 심했다. 5. FV 및 DNV 감염잠에서 중장과 체액의 단백질은 바이러스 접종 중기까지는 건전잠에 비해 큰 변화가 없었으나, 접종 말기에서는 건전잠에서 보다 월등히 낮았다. 6. 바이러스 접종 8일 후의 FV 및 DNV 감염잠 중장 RNA 전기영동상은 건전잠의 중장 RNA인 26S, 17S, 5S 및 4S의 4종 band와 동일했다. 7. FV 및 DNV 감염잠의 중장 단백질 전기영동상은 바이러스 접종 1일과 5일 후에는 건전잠의 것과 큰 차이가 없고, 접종 8일 후에는 건전잠에 존재하는 이동도가 낮은 L band가 양 바이러스 감염잠에서는 공히 소실되는 반면, 건전잠에서 볼 수 없는 이동도가 중간인 M band가 새로이 나타났으며 비교적 이동도가 높은 건전잠의 N band는 양 바이러스 감염잠에서는 2개로 분리되었다. 8. 체액단백질의 전기영동상은 FV 및 DNV감염잠 공히 건전잠의 것과 유사하나, 바이러스 접종 8일 후에는 양적인 감소를 나타내어 건전잠의 약 40%에 지나지 않았다. 9. FV 감염중장조직을 pyronin-methyl green 2종 염색을 하여 광학현미경으로 관찰한 결과, 바이러스 접종 8일 후의 중장원동세포내에서 A형 및 B형 봉입체가 형성되었음을 확인하였다. 10. FV감염 중장조직세포의 전자현미경 관찰에서는 바이러스 접종 5일 후에 배상세포의 'cytoplasmic wall'이 비대해지고 그 내부에 virus-specific vesicle이 형성되었으며, 바이러스 접종 8일 후에는 virus-specific vesicle, 바이러스 입자, linear structure, tubular structure 및 전자밀도가 높은 matrix 등의 바이러스 감염에 대한 특이적인 구조물이 배상세포의 세포질에서 관찰되었으며, microvilli내에서 바이러스 입자의 존재도 확정되었다. 특히 virus-specific vesicle 주위에서는 전자밀도가 높은 구형의 바이러스 입자 유사체가 관찰되었는데, 이것은 virus-specific vesicle 주위에서 바이러스 조립이 일어나는 것을 추정된다. 한편 원통세포 내에서 봉입체 관찰되고, 변형소구화된 배상세포가 중장강으로 탈락되는 것이 관찰되었다. 11. DNV감염 중장조직을 acridine orange 염색을 하여 형광현미경으로 관찰한 결과, DNV접종 5일 후에 본 바이러스 증식 장소인 원동세포핵의 비대가 뚜렷이 관찰되었다. 12. 전자현미경에 의해 DNV감염 중장조직세포를 관찰한 결과, 바이러스 접종 5일 후에 원동세포 핵내의 인이 소형 과립으로 붕괴되어 산재되었고, 접종 8일후에는 전자밀도가 높은 virogenic stroma가 출현하였으며, 감염 말기로 추정되는 핵내의 전자밀도가 전자보다 낮고 더욱 확대되어 핵의 대부분을 차지하는 virogenic stroma도 관찰되었다. 또한 이들 virogenic stroma내에서 바이러스 입자유사체가 관찰되는 것으로 보아 이 virogenic stroma는 바이러스 전구물질의 합성 및 바이러스 조립장소임을 시사하고 있다.