• Journal of the Korean Ceramic Society
• /
• v.48 no.2
• /
• pp.173-177
• /
• 2011

Decomposition promoting factors and decomposition mechanism in the zinc decomposition process of waste hard metals which are composed mostly of tungsten carbide and cobalt were evaluated. Zinc volatility amount was suppressed and zinc valatilization pressure was produced in the reaction graphite crucible inside an electric furnace for ZDP. Reaction was done for 2 h at $650^{\circ}C$, which 100 % decomposed the waste hard metals that were over 30 mm thick. As for the separation-decomposition of waste hard metals, zinc melted alloy formed a liquid composed of a mixture of ${\gamma}-{\beta}1$ phase from the cobalt binder layer (reaction interface). The volume of reacted zone was expanded and the waste hard metal layer was decomposed-separated horizontally from the hard metal. Zinc used in the ZDP process was almost completely removed-collected by decantation and volatilization-collection process at $1000^{\circ}C$.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2003.11a
• /
• pp.78-82
• /
• 2003

For the decomposition of laundry wastewater containing Fe-EDTA produced from the steam generators in nuclear power plants, Supercritical Water Oxidation (SCWO) Process, Photocatalytic Oxidation (PO) Process, and Dielectric Barrier Discharge (DBD) Atmospheric Pressure Plasma Process were evaluated. Even though EDTA was converted over 99.98 % by the SCWO process, it was estimated that the countermeasure against corrosion of the equipment should be reinforced for the process stability. It was considered that the PO process is not appropriate for the decomposition of high concentrated laundry wastewater since the conversion ratio of EDTA was around 10 %. Finally, High efficiency of the decomposition of organic matter (methylene blue) was obtained using DBD process even low energy was supplied. However there is still room for the evaluation of EDTA decomposition in order that the DBD process should be applied for the field samples.

• Journal of Environmental Science International
• /
• v.12 no.12
• /
• pp.1255-1260
• /
• 2003

Plasma-photocatalytic oxidation process was applied in the decomposition of Triethylamine(TEA) and Methyl ethyl ketone(MEK). Plasma reactor was made entirely of pyrex glass and consists of 24mm inner diameter, 1,800mm length and discharge electrode of 0.4mm stainless steel. And initial concentrations of TEA and MEK for plasma-photocatalytic oxidation are 100 ppm. Odor gas samples were taken by gas-tight syringe from a glass sampling bulb which was located at reactor inlet and outlet, and TEA and MEK were determined by GC-FID. For plasma process, the decomposition efficiency of TEA and MEK were evaluated by varying different flowrates and decomposition efficiency of TEA and MEK increased considerably with decreasing treatment flowrates. For photocatalytic oxidation process, also the decomposition efficiency of TEA and MEK increased considerably with decreasing treatment flowrates. The decomposition efficiency of MEK was 57.8％, 34.2％, 18.8％ respectively and the decomposition efficiency of TEA was reached all 100％. This result is higher than that of plasma process only, From this study, the results indicate that plasma-photocatalytic oxidation process is ideal for treatment of TEA and MEK.

• Transactions of the Korean hydrogen and new energy society
• /
• v.34 no.6
• /
• pp.594-600
• /
• 2023

In this study, a process model and optimization design direction for a hydrogen production plant through ammonia decomposition are presented. If the reactor decomposition rate is designed to approach 100%, the amount of catalyst increases and the devices that make up the entire system also have a large design capacity. However, if the characteristics of the hydrogen regeneration process are reflected in the design of the reactor, it becomes possible to satisfy the total flow rate of fuel gas with the discharged tail gas flow rate. Analyzing the plant process simulation results, it was confirmed that when an appropriate decomposition rate is maintained in the reactor, the phenomenon of excess or shortage of fuel gas disappears. In addition, it became possible to reduce the amount of catalyst required and design the optimized capacity of the relevant processes.

• Journal of the Korean Society of Industry Convergence
• /
• v.6 no.4
• /
• pp.269-275
• /
• 2003

A non-thermal plasma process combined with $Cr_2O_3/TiO_2$ catalyst was applied to the decomposition of trichloroethylene (TCE). A dielectric barrier discharge reactor operated with AC high voltage was used as the non-thermal plasma reactor. The effects of reaction temperature and input power on the decomposition of TCE and the formation of byproducts including HCl, $Cl_2$, CO, NO, $NO_2$ and $O_3$ were examined. At an identical input power, the increase in the reaction temperature from 373 K to 473 K decreased the decomposition of TCE in the plasma reactor. The presence of the catalyst downstream the plasma reactor not only enhanced the decomposition of TCE but also affected the distribution of byproducts, significantly. However, synergistic effect as a result of the combination of non-thermal plasma with catalyst was not observed, i.e., the TCE decomposition efficiency in this plasma-catalyst combination system was almost similar to the sum of those obtained with each process.

• Journal of the Korea Safety Management & Science
• /
• v.1 no.1
• /
• pp.241-258
• /
• 1999

For hazardous air pollutants(HAP) such as NO and $NO_{2}$ decomposition efficiency, power consumption, and applied voltage were investigated by SPCP(surface induced discharge plasma chemical processing) reactor to obtain optimum process variables and maximum decomposition efficiencies. Decomposition efficiency of HAP with various electric frequencies(5~50 kHz), flow rates(100~1,000 mL/min), initial concentrations(100~1,000 ppm), electrode materials(W, Cu, Al), electrode thickness(1, 2, 3 mm) and number of electrode windings(7, 9, 11) were measured. Experimental results showed that for the frequency of 10 kHz, the highest decomposition efficiency of 94.3 % for NO and 84.7 % for $NO_{2}$ were observed at the power consumptions of 19.8 and 20W respectively and that decomposition efficiency decreased with increasing frequency above 20 kHz. Decomposition efficiency was increased with increasing residence times and with decreasing initial concentration of pollutants. Decomposition efficiency was increased with increasing thickness of discharge electrode and the highest decomposition efficiency was obtained for the electrode diameter of 3 mm in this experiment. As the electrode material, decomposition efficiency was in order : tungsten(W), copper(Cu), aluminum(Al).

• Nuclear Engineering and Technology
• /
• v.54 no.12
• /
• pp.4441-4448
• /
• 2022

The electrochemical oxidation process has been widely studied in the field of wastewater treatment for the decomposition of organic materials through oxidation using ·OH generated on the anode. Pt anode electrodes with high durability and long-term operability have a low oxygen evolution potential, making them unsuitable for electrochemical oxidation processes. Therefore, to apply Pt electrodes that are suitable for long-term operation and large-scale processes, it is necessary to develop a new method for improving the decomposition rate of organic materials. This study introduces a method to improve the decomposition rate of organic materials when using a Pt anode electrode in the electrochemical oxidation process for the treatment of organic decontamination liquid waste. Electrochemical decomposition tests were performed using sodium dodecylbenzenesulfonate (SDBS) as a representative organic material and a Pt mesh as the anode electrode. Y₂O₃ particles were introduced into the electrolytic cell to improve the decomposition rate. The decomposition rate significantly improved from 21% to 99%, and the current efficiency also improved. These results can be applied to the electrochemical oxidation process without additional system modification to enhance the decomposition rate and current efficiency.

• Transactions of the Korean hydrogen and new energy society
• /
• v.20 no.5
• /
• pp.397-403
• /
• 2009

The catalysis of carbon black was investigated for the production of hydrogen by the catalytic decomposition of propane-butane mixture gas in this study. The thermal and the catalytic decompositions of hydrocarbons were performed at the temperature range of 500 - $1100^{\circ}C$, respectively. The conversions of hydrocarbons and the mole traction of hydrogen increased with increasing the reaction temperature and the conversion of hydrocarbons in the catalytic decomposition process was approximately liked with that obtained by the thermal decomposition. However, the mole traction of hydrogen produced in the catalytic decomposition process was higher than that obtained from the thermal decomposition. Therefore, it was concluded that the catalysis for the decomposition of hydrocarbons is occurred over carbon black used as catalyst. The mole traction of hydrogen produced by the catalytic decomposition of hydrocarbons also increased with increasing the mole ratio of $C_3H_8/C_4H_{10}$ in propane and butane mixture gas at $700^{\circ}C$. Therefore, it was concluded that the catalytic decomposition of the high propane mixture gas is more effectively for the production of hydrogen.

• Korean Journal of Computational Design and Engineering
• /
• v.5 no.4
• /
• pp.359-372
• /
• 2000

Current CAD systems are good enough to be used as a tool to manipulate three-dimensional shapes. This is a very important capability to be owned by a design tool because a major portion of designers'activities is spent on the shape manipulation in the design detailing process. However, the whole design process involves a lot more than the, shape manipulation. Currently, these remaining tasks, mostly logical reasoning process for the function realization together with structure decomposition in the top-down manner, are processed in the designer's brain. To support the top-down functional design process of a mechanical product, a system integrating the functional, structural and geometrical aspects of a product design in a unified environment is presented. Using this system, a designer can perform function decomposition, structure decomposition, and geometry detailing, and function verification activities in parallel and the whole design process it modeled resultantly. Once the whole design process is modeled, any redesign task can be automatically performed with the verification of the desired functions.

• Journal of the Korean Society of Combustion
• /
• v.10 no.4
• /
• pp.24-32
• /
• 2005

Various types of plasma source applied in $CH_4$ decomposition process are compared. DBD by pulse and AC power, spark by pulse and AC power, rotating arc and hollow cathode plasma are chosen to be compared. The results show that $CH_4$ conversion per given unit power is relatively high in hollow cathode plasma and rotating arc that induces rather high temperature condition and that is why both thermal dehydration and plasma induced decomposition contribute for the overall process. In case of DBD wherein high temperature electron and low temperature gas molecule coexist, the process shows low conversion rate, for in rather low temperature condition the contribution of thermal dehydration is lowered. Selectivity of $C_2H_6$ and $C_2H_2$ is shown to be a good parameter of the relative contribution of plasma chemistry in the overall process. From the results we concluded that required condition of plasma source for a cost effective and high yield $CH_4$ decomposition is to have characteristics of both thermal plasma and non thermal plasma in which temperature is high above a certain threshold state for thermal dehydration and electron induced collision is maximized in the same breath.