• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.10
• /
• pp.6439-6444
• /
• 2015

With increasing concern about global warming, CCS (Carbon dioxide capture and storage) has attracted much attention as a promising technology for reducing $CO_2$ emission. It is necessary to develop the cost-effective absorbents materials in order to rapid commercialize CCS technologies. In this work, he study for the promotion of absorption rate in $CO_2$ capture system using metal nanoparticle were investigated. Three kinds of metal nanoparticle, cobalt, zinc, and nickel, were prepared by wet and dry method and effect of preparation method on the absorption rate of $CO_2$ were compared. Among the tested using pH method, nickel nanoparticle prepared by wet method showed the most significant improvement of $CO_2$ absorption rate. In case that metal nanoparticle is applied to CCS process, it is expected to be more efficient in $CO_2$ capture process due to reduce the size of absorption tower.

• Clean Technology
• /
• v.10 no.2
• /
• pp.111-120
• /
• 2004

Manufacturing with a chemical for eco-friendly leather for nitrogen decrease of leather falling hair process waste water and the falling hair process that a number to decrease with sulfuration water decrease, a pollution load of COD, BOD. In this study manufactured lining agent and the unhairing assist product which did urea, mercaptan by basic matter. As a result of having dealt in hair saving process, compared, and was recalled by the existing hair burning process recovered hair, increased approximately 2times. Grain state to influence the yield that was quality of leather and an index of productivity evaluation, an improvement of contraction phenomenon (drawing) were possible. Is increased going seal, tear strength property of matter and softness and touch leather native nature in wet blue. Also, it is possible confirmation with decrease being more possible than about 50% COD, T-N density in a hair saving waste water.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.2
• /
• pp.321-328
• /
• 2019

A military shelter for communication and information is necessary to optimize the integrated combat ability of weapon systems in the network centric warfare. Therefore, the military shelter is required for EMI shielding performance. This study examines the stable measurement points for EMI shielding effectiveness of a military shelter for communication and information. The measurement points were found by analyzing the EMI shielding effectiveness measurement data with data mining technique and process capability analysis. First, a support vector machine was used to separate the measurement point that has stable EMI shielding effectiveness according to set condition. Second, this process was conducted with process capability analysis. Finally, the results of data mining technique were compared with those of process capability analysis. As a result, 24 measurement points with stable EMI shielding effectiveness were found.

• Journal of Powder Materials
• /
• v.27 no.6
• /
• pp.490-497
• /
• 2020

The 3D printing process provides a higher degree of freedom when designing ceramic parts than the conventional press forming process. However, the generation and growth of the microcracks induced during heat treatment is thought to be due to the occurrence of local tensile stress caused by the thermal decomposition of the binder inside the green body. In this study, an alumina columnar specimen, which is a representative ceramic material, is fabricated using the digital light process (DLP) 3D printing method. DTG analysis is performed to investigate the cause of the occurrence of microcracks by analyzing the debinding process in which microcracks are mainly generated. HDDA of epoxy acrylates, which is the main binder, rapidly debinded in the range of 200 to 500℃, and microcracks are observed because of real-time microscopic image observation. For mitigating the rapid debinding process of HDDA, other types of acrylates PETA, PUA, and MMA are added, and the effect of these additives on the debinding rate is investigated. By analyzing the DTG in the 25 to 300℃ region, it is confirmed that the PETA monomer and the PUA monomer can suppress the rapid decomposition rate of HDDA in this temperature range.

• Proceedings of the Korea Contents Association Conference
• /
• 2007.11a
• /
• pp.183-187
• /
• 2007

During the recent decades in democratic and industrialized countries, government policies for governing technological innovation and risks to environment and human health have undergone significant changes. The shift from a top-down legislative approach to a more inclusive and deliberative atmosphere is, putatively the most prominent change. Such a move is often described as a move from government to governance. In the governance of technology and risk, public engagement has been a major strategy in technology decision-making process. This article aims to look into the changes in the procedural modes of technology decision-making process. It discusses the main viewpoints that have been placed on the basis of such a move. Also, it further relates the changes in local decision-making process to science and technology decision-making at global level. It argues that the democratic and reflexive trends in local science and technology decision-making will be the basis upon which to shape and respond to global governance system: while international decision-making process would require accountability in integrating different values and rationalities, such accountability may be sustained and reinforced depending on the robustness of the local decisions and social choices.

• Korean Chemical Engineering Research
• /
• v.46 no.3
• /
• pp.443-450
• /
• 2008

Efficient use of low rank coals (LRC) have been investigated as a method to cope with recent high oil price. Among the coals used in industry, lignite and sub-bituminous coals are belong to the LRC, and have abundant deposit and are distributed worldwide, but high moisture contents and self ignition properties inhibits their utilization. In this paper, chemical coal cleaning to produce ash-free coal from LRC has been investigated. Two technologies, that is, UCC(Ultra Clean Coal) process removing ash from coal and Hyper Coal process extracting combustibles from coal were compared with. UCC process has merits of simple and reliable when it compared with Hyper Coal process, but the remaining ash contents werehigher than Hyper Coal. Hyper Coal has ash contents under the 200ppm when raw coal is treated with appropriate solvent and ion exchange materials to remove alkali materials in extracted solution. The ash-free coal which is similar grade with oil can be used as alternate oil in the industry, and also used as a high grade fuel for IGCC, IGFC and other advanced combustion technology.

• Design & Manufacturing
• /
• v.13 no.1
• /
• pp.55-60
• /
• 2019

Smart-phone in the recently released high-end applied to the camera module is equipped with the most features auto focusing camera module. Also, auto focusing camera module is divided into voice coil motor, encoder, and piezo according to type of motion mechanism. Auto focusing camera module is composed of voice coil motor (VCM) as an actuator and leaf spring as a guide and suspension. VCM actuator is made of magnet, yoke as a metal, and coil as a copper wire. Recently, the assembly as yoke and magnet is made by human resources. These process has a long process time and it is difficult to secure quality. Also, These process is not economical in cost, and productivity is reduced. Therefore, an automatic assembly as yoke and magnet is needed in the present process. In this paper, we have developed an automatic assembly device that can automatically assemble yoke and magnet, and performed verifying performance. Therefore, by using the developed automatic assembly device, it is possible to increase the productivity and reduce the production cost.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.2
• /
• pp.130-136
• /
• 2000

Generally, the build-up printed circuit board manufactured by the sequential process with etching, plating, drilling etc. requires many types of equipments and lead time. Etching process is suitable for mass production, however, it is not adequate for manufacturing prototype in the developing stage. In this study, we introduce a screen printing technology to prototyping a build-up printed circuit board. As for the material, photo/thermal curable resin and conductive paste are used for the formation of dielectric and conductor. The build-up structure is made by subsequent processes such as the formation of liquid resin thin layer, the solidification by UV/IR light, and via filling with conductive paste. By use of photo curable resin, productivity is greatly enhanced compared with thermal curable resin. Finally, the basic concept and the possibility of build-up printed circuit board prototyping are proposed in comparison with to the conventional process.

• Proceedings of the Technology Innovation Conference
• /
• 1999.06a
• /
• pp.176-202
• /
• 1999

Korea has exerted her efforts to assimilate nuclear power technology, and reportedly localized 95 percent of nuclear power technology by 1995. This paper investigates the evolution of nuclear power program in Korea to exploit the development process of the nuclear power industry and key factors for the technological localization of nuclear power plant. In developing countries, an imitative catching-up process can be shown as a course for developing the absorptive capacity of foreign technology, which depends on prior knowledge base and the intensity of effort. The process of technological learning consists of five stages including preparation, implementation of foreign technology, acquisition of peripheral technology, acquisition of core technology, and improvement f foreign technology. Moreover, this paper discusses six essential factors that have influenced the successful achievement of technological localization of nuclear power plants in Korea. They include the role and strategies of the government, the leading role of utility firm, the development and cooperation of the related organizations, the development of human resources and their efforts, market conditions and the assistance of foreign donors, and social conditions. Finally, this paper discusses about implications offered by the Korean experience for other developing countries.

• Journal of Korea Technology Innovation Society
• /
• v.5 no.1
• /
• pp.26-43
• /
• 2002

Korean government has been putting efforts to promote development of technologies by government sponsored labs and to transfer, diffuse, and commercialize these technologies in private sector since mid 1980s. In spite of these efforts, utilization of government-sponsored technology remains in the very low level. According to the survey conducted by Korea Intellectual and Patent Office (1999), the ratio of unused industrial property rights including patents was above 70% of total industrial property rights. Survey on the information and telecommunication industry done by the Institute of Information Technology Assessment (IITA) in 1999 shows that the utilization ratio of government-sponsored technologies is about 55.8%. This is especially true where government is not the primary or end-user of technologies. The purposes of this paper are to (1) identify a process model of technology commercialization, (2) develop the related variables of each step in the six-step continuous process model of government-sponsored technology commercialization, (3) empirically investigate the data gathered through questionnaire survey, and (4) suggest policy alternatives for promoting technology commercialization in Information and Telecommunication industries.