• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.134-134
• /
• 2009

In this work, we report that crystallization speed as well as the electrical and optical properties about the N-doped $Ge_2Sb_2Te_5$ thin films. The 200-nm-thick N-doped $Ge_2Sb_2Te_5$ thin film was deposited on p-type (100) Si and glass substrate by RF reactive sputtering at room temperature. The amorphous-to-crystalline phase transformation of N-doped $Ge_2Sb_2Te_5$ thin films investigated by X-ray diffraction (XRD). Changes in the optical transmittance of as-deposited and annealed films were measured using a UV-VIS-IR spectrophotometer and four-point probe was used to measure the sheet resistance of N-doped $Ge_2Sb_2Te_5$ thin films annealed at different temperature. In addition, the surface morphology and roughness of the films were observed by Atomic Force Microscope (AFM). The crystalline speed of amorphous N-doped $Ge_2Sb_2Te_5$ films were measured by using nano-pulse scanner with 658 nm laser diode (power : 1~17 mW, pulse duration: 10~460 ns). It was found that the crystalline speed of thin films are decreased by adding N and the crystalline temperature is higher. This means that N-dopant in $Ge_2Sb_2Te_5$ thin film plays a role to suppress amorphous-to-crystalline phase transformation.

• Transactions of the Korean hydrogen and new energy society
• /
• v.17 no.1
• /
• pp.62-68
• /
• 2006

High temperature electrolysis is a promising technology to produce massively hydrogen using renewable and nuclear energy. Solid oxide fuel cell materials are candidates as the components of steam electrolysers. However, the polarization characteristics of the typical electrode materials during the electrolysis have not been intensively investigated. In this study, NiO electrode was deposited on YSZ electrolyte by spin coat process and firing at $1300^{\circ}C$. Pt electrode was applied on the other side of the electrolyte to compare the polarization characteristics with those by NiO during electrolysis. The $H_2$ evolution rate was also monitored by measuring the electromotive force of Lambda probe and calculated by thermodynamic consideration. At low current density, Pt showed lower cathodic polarization and thus higher current efficiency than Ni, but the oxidation of Ni into NiO caused the increase of anodic resistance with increasing current density. High overpotential induced high power consumption to produce hydrogen by electrolysis.

• Food Science of Animal Resources
• /
• v.40 no.4
• /
• pp.551-562
• /
• 2020

Beef fat was replaced with cold press pumpkin seed oil (PSO; 0%, 5%, 15%, and 20%) in the production of bologna-type sausages. A value of pH, water-holding capacity (WHC), jelly-fat separation, emulsion stability and viscosity values were determined in meat batters. Thiobarbituric acid reactive substances (TBARS), color, and textural characteristics (TPA, shear test, penetration test) were determined in end-product at 1, 7, 14, 21, and 28 days of storage at 4℃. The pH values were varied between 6.06 and 6.08. With the increase in the level of PSO in meat batters, there was a significant increase in WHC, jelly-fat separation and viscosity values (p<0.05) while a significant decrease in emulsion stability (p<0.05). TBARS values of sausages were found to be significantly higher than in the control group (p<0.05), and this trend continued during storage. Increasing of PSO level were caused a significant increase in L* and b* values while a decrease in a* value (p<0.05). Hardness, adhesiveness and chewiness values were significantly reduced whereas cohesiveness and resilience values increased (p<0.05). Maximum shear force and work of shear was significantly decreased as the level of PSO increased (p<0.05). Hardness, work of penetration and the resistance during the withdrawal of the probe values (penetration tests) increased significantly with the increase in the level of PSO (p<0.05). These results indicate that PSO has potential to be use as a replacement of animal-based fats in the production of bologna-type sausages.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.2
• /
• pp.213-223
• /
• 1997

Premixed flame is better than diffusion flame to accomplish a high loading combustion. Since the turbulent characteristics of unburned mixture has a great influence on the flame structure, it is general that many researchers realize a high loading combustion with strengthening turbulent intensity of unburned mixture. Because turbulent premixed flame reacts efficiently on the condition of distributed reaction region, we made high turbulent premixed flame in the doubled impingement field. We investigated turbulent characteristics of unburned mixture with increasing shear force and visualized flames with direct and Schlieren photographs. And the combustion characteristics of flame was elucidated by instantaneous temperature measurement with a thermocouple, by ion currents with a micro electrostatic probe, by radical luminescence intensity and local equivalence ratio. Extremely strong turbulent of small scale is generated by impingement of mixture, and turbulent intensity of unburned mixture increased with the mean velocity. As a result of direct photographs, visible region of flame became longer due to increasing central direction flux. But as strengthed turbulent intensity, visible region of flame turned to shorter and reaction occurred efficiently. As strengthened turbulent intensity of mixture with increasing flux of central direction, maximum fluctuating temperature region moved to radial direction and fluctuation of temperature became lower. The reason is influx of central direction which caused flame zone to move toward radial direction, to maintain flame zone stable and to make flame scale smaller.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.32.2-32.2
• /
• 2011

반도체 생산공정에서 CMP (Chemical-mechanical planarization) 공정은 우수한 전기전도성 재료인 Cu의 사용과 다층구조의 소자를 형성하기 위해서 도입되었으며, 최근 소자의 집적도가 증가함에 따라 CMP 공정 비중은 점점 높아지고 있다. Cu CMP 공정에서 연마제인 슬러리는 금속 표면과의 물리적 화학적 반응을 동시에 사용하여 표면을 연마하게 되며, 연마특성을 향상시키기 위해 산화제, 부식방지제, 분산제 및 다양한 계면활성제가 첨가된다. 하지만 슬러리는 Cu 표면을 평탄화하는 동시에 오염입자, 유기오염물, 스크레치, 표면부식 등을 발생시키며 결과적으로 소자의 결함을 야기시킨다. 특히 부식방지제로 사용되는 BTA (Benzotriazole)은 Cu CMP 공정 중 Cu-BTA 형태로 표면에 흡착되어 오염원으로 작용하며 입자오염을 증가시시고 건조공정에서 물반점 등의 표면 결함을 발생시킨다. 이러한 문제점을 해결하기 위해 Cu 표면에서 식각과 부식반응을 최소화하며, 오염입자 제거 및 유기오염물을 효과적으로 제거하기 위한 Post-CMP 세정 공정과 세정액 개발이 요구된다. 본 연구에서는 오염입자 및 유기물 제거와 동시에 표면 거칠기와 부식현상을 제어할 수 있는 post Cu CMP 세정액을 개발 평가하였다. 오염입자 및 유기오염물을 제거하기 위해서 염기성 용액인 TMAH 사용하였으며, Cu 이온을 용해할 수 있는 Chelating agent와 표면 부식을 억제하는 부식 방지제를 사용하여 세정액을 합성하였다. 접촉각 측정과 FESEM(field Emission Scanning Electron Microscope) 분석을 통하여 CMP 공정에서 발생하는 유기오염물과 오염입자의 흡착과 제거를 확인하였으며 Cu 웨이퍼 세정 전후의 표면 거칠기의 변화와 식각량을 AFM(Atomic Force Microscope)과 4-point probe를 사용하여 각각 평가하였다. 또한 세정액 내에서의 연마입자의 zeta-potential을 측정 및 조절하여 세정력을 향상시켰다. 개발된 세정액과 Cu 표면에서의 화학반응 및 부식방지력은 potentiostat를 이용한 전기화학 분석법을 통해서 chelating agent와 부식방지제의 농도를 최적화 시켰다. 개발된 세정액을 적용함으로써 Cu-BTA 형태의 유기오염물과 오염입자들이 효과적으로 제거됨을 확인하였다.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.12
• /
• pp.2283-2287
• /
• 2007

Amyloid fibril formation of amyloid β/A4 protein (Aβ) is critical to understand the pathological mechanism of Alzheimer's disease and develop controlling strategy toward the neurodegenerative disease. For this purpose, dequalinium (DQ) has been employed as a specific modifier for Aβ aggregation and its subsequent cytotoxicity. In the presence of DQ, the final thioflavin-T binding fluorescence of Aβ aggregates decreased significantly. It was the altered morphology of Aβ aggregates in a form of the bundles of the fibrils, distinctive from normal single-stranded amyloid fibrils, and the resulting reduced β-sheet content that were responsible for the decreased fluorescence. The morphological transition of Aβ aggregates assessed with atomic force microscope indicated that the bundle structure observed with DQ appeared to be resulted from the initial multimeric seed structure rather than lateral association of preformed single-stranded fibrils. Investigation of the seeding effect of the DQ-induced Aβ aggregates clearly demonstrated that the seed structure has determined the final morphology of Aβ aggregates as well as the aggregative kinetics by shortening the lag phase. In addition, the cytotoxicity was also varied depending on the final morphology of the aggregates. Taken together, DQ has been considered to be a useful chemical probe to control the cytotoxicity of the amyloid fibrils by influencing the seed structures which turned out to be central to develop therapeutic strategy by inducing the amyloid fibrils in different shapes with varied toxicities.

• Journal of Periodontal and Implant Science
• /
• v.24 no.3
• /
• pp.649-660
• /
• 1994

The purpose of this study was to evaluate the effects of administration of Zea Mays L. on the healing process after periodontal surgery as adjuntives. Authors used 3 kinds of different clinical criteria, depth of periodontal pocket by using the Goldman Fox periodontal probe, degree, of tooth mobility by Periotest, and amount of occlusal force with electronic device. In this comparative clinical study, 30 patients who were divided into two group, 15 ZML administrated group and 15 placebo adminstrated group, were participated. All the examined teeth were isolated with gauze and air spray, and measured each clinical critera on the day of before surgery, 1, 2, 4, 8 weeks after surgery. The results were as follows. 1. The changes of the periodontal pocket depth, on the both of Zea Mays L. administrated group and placebo adminstrated group, revealed the decreasing tendency, and it was shown the time dependent tendency. But there was no statistically significant differences between the two group. 2. In the case of tooth mobility, both group showed the highest severe mobility on the 1 week after surgery. It was observed that experimental group had more effects on decreasing the mobility. But there was no statistically significant differences between the two group. 3. In the case of experimental group, the recovery trend of occlusal forces after periodontal surgery on the molar teeth revealed higher than the control group. But there was no statistically significant differences between the two group. In conclusion, Zea Mays L. may play a favorable role in the healing process after periodontal surgery. It was suggested that further study to evaluate the effects of selective administration on the patient who have systemic diseases should be needed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.238-239
• /
• 2010

Dimethyl sulphoxide (DMSO) is one of the widely-used secondary dopants in order to enhance the conductivity of poly(3, 4-ethylenedioxy-thiophene):poly(styrene sulfonate) (PEDOT:PSS) film. In this work, we investigated the effect of DMSO doping in to PEDOT:PSS on the electrical performance of the bulk heterojunction photovoltaics consisting of poly(3-hexylthiophene-2, 5-diyl) and phenyl-C61-butyric acid methyl ester. Correlation between the power conversion efficiency and the mechanism of improving conductivity, surface morphology, and contact properties was examined. The PEDOT:PSS films, which contain different concentration of DMSO, have been prepared and annealed at different annealing temperatures. The mixture of DMSO and PEDOT:PSS was prepared with a ratio of 1%, 5%, 15%, 25%, 35%, 45%, 55% by volume of DMSO, respectively. The DMSO-contained PEDOT:PSS solutions were stirred for 1hr at $40^{\circ}C$, then spin-coated on the ultra-sonicated glass. The spin-coated films were baked for 10min at $65^{\circ}C$, $85^{\circ}C$, and $120^{\circ}C$ in air. In order to investigate the electrical performance, P3HT:PCBM blended film was deposited with thickness of 150nm on DMSO-doped PEDOT:PSS layer. After depositing 100nm of Al, the device was post-annealed for 30min at $120^{\circ}C$ in vacuum. The fabricated cells, in this study, have been characterized by using several techniques such as UV-Visible spectrum, 4-point probe, J-V characteristics, and atomic force microscopy (AFM). The power conversion efficiency (AM 1.5G conditions) was increased from 0.91% to 2.35% by tuning DMSO doping ratio and annealing temperature. It is believed that the improved power conversion efficiency of the photovoltaics is attributed to the increased conductivity, leading to increasing short-circuit current in DMSO-doped PEDOT:PSS layer.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.36 no.6
• /
• pp.490-495
• /
• 2016

Pulsed eddy current (PEC) testing signals have typically been obtained from the electromotive force induced in a sensor coil. However, an increasing number of studies have elected to incorporate the Hall plate as a sensor. Thus, accurate numerical modeling of the Hall sensor signal is necessary. In this study, a PEC probe is designed and a numerical modeling program is written so that Hall sensor signals and coil sensor signals can be calculated simultaneously. First, a step current is used as the input current. The predicted Hall sensor signals show similar characteristics to those of the experimental signals reported by other researchers. The characteristics of the two types of signals are then analyzed and compared as the thickness of test object changes. The results show that the Hall sensor signal provides less information for evaluating the thickness of the test object than the coil sensor signal. The response signals from a pulsed input current are also calculated, and it is confirmed that an equivalent reversed signal pattern appeared after the pulse width at both signals.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.11
• /
• pp.1631-1636
• /
• 2010

In this study, we demonstrate a nano-scale lithograph obtained on localized (100) silicon (p-type) surface using by modified AFM (Atomic force microscope) apparatuses and by adopting controlling methods. AFM-based experimental apparatuses are connected to a customized pulse generator that supplies electricity between the conductive tip and the silicon surface, while maintaining a constant humidity throughout the lithography process. The pulse durations are controlled according to various experimental conditions. The electrochemical reaction induced by the pulses occurs in the gap between the conductive tip and silicon surface and result in the formation of nanoscale oxide particles. Oxide particles with various heights and widths can be created by AFM surface modification; the size of the oxide particle depends on the pulse durations and the applied electrical conditions under a humid environment.