• Tribology and Lubricants
• /
• v.17 no.4
• /
• pp.276-282
• /
• 2001

Nano adhesion between SPM (scanning probe microscope) tips and 075 (octadecyltrichlorosilane) SAM (self-assembled monolayer) was experimentally studied. Tests were performed to measure the nano adhesion and friction in both AFM(atomic force microscope) and LFM(lateral force microscope) modes in various conditions of relative humidity. OTS SAM was formed on Si-wafer (100) surfaces, and Si$_3$N$_4$ tips of different radius of curvature were used. When the surface was hydrophobic, the adhesion and friction forces were found lower than those of bare Si-wafer. Results also showed that micro-adhesion force increased as the relative humidity and the tip radius of curvature increased. The main parameter for affecting the micro-adhesion was found absorbed humidity on the contact surface. These results were discussed with the JKR model and a capillary force caused by absorbed water.

• Laser Solutions
• /
• v.6 no.3
• /
• pp.11-17
• /
• 2003

Recoil force exerted on the substrate during a nanosecond laser ablation of silicon is measured. The ablation sample is placed at the end of a 400 $\mu\textrm{m}$ thick and 13 mm long silicon cantilever. The vibration amplitude of the cantilever induced by the recoil force is measured in real time with a probe beam. By comparing the deflection amplitude of the cantilever with a theoretical model, the recoil momentum is estimated. For laser irradiance in the order of 10$\^$11/ W/$\textrm{cm}^2$, the recoil pressure reached a value over 40${\times}$10$\^$9/ Pa.

• Proceedings of the KSME Conference
• /
• 2005.11a
• /
• pp.151.2-151.2
• /
• 2005

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.3
• /
• pp.5-14
• /
• 2003

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.10
• /
• pp.1833-1841
• /
• 2000

Microelectrode probe was made and applied to the biofilm in the biological treatment process as the state-of-art technology in order to actually measure the biofilm thickness, ionic concentration gradient, and material transport, etc. instead of classical theoretical approach. The working microelectrode, one of the main components of microelectrode probe, was easily contaminated and broken when determining the differences in the ionic concentrations through the measurement of biofilm's EMF (electromotive force). As a demonstration, two microelectrode probes were constructed in our lab for the measurement of the pH and $NO_3{^-}$ concentration in denitrifying biofilm. The microelectrode probe through the inner biofilm ($350{\mu}m$ from the surface of biofilm) showed that the pH was increased from pH 8 in the bulk solution to pH 8.3, on the other hand, the $NO_3{^-}$ concentration was decreased from 30 fig N/L in the bulk solution to 4 fig N/L.

• Journal of the Microelectronics and Packaging Society
• /
• v.12 no.4 s.37
• /
• pp.289-299
• /
• 2005

The ball shear force was investigated in terms of test parameters, i.e. displacement rate and probe height, with an experimental and non-linear finite element analysis for evaluation of the solder joint integrity in area array packages. The increase in the displacement rate and the decrease in the probe height led to the increase in the shear force. Excessive probe height could cause some detrimental effects on the test results such as unexpected high standard deviation and probe sliding from the solder ball surface. The low shear height conditions were favorable for assessing the mechanical integrity of the solder joints. The mechanical and electrical properties of the Sn-37Pb/Cu and Sn-3.5Ag/Cu BGA solder joints were also investigated with the number of reflows. The total thickness of the intermetallic compound (IMC) layers, consisting of Cu6Sn5 and Cu3Sn, was increased as a function of cubic root of reflow time. The shear force was increased up to 3 or 4 reflows, and then was decreased with the number of reflows. The fracture occurred along the bulk solder, in irrespective of the number of reflows. The electrical resistivity was increased with increasing the number of reflows.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.637-640
• /
• 2005

In this paper, we investigate the characteristics of a piezoresistive AFM cantilever in the range of $0\~30{\mu}N$ by using nano force calibrator (NFC), which consists of a high precision balance with resolution of 1 nN and 1-D fine positioning stage. Brief modeling of the cantilever is presented and then, the calibration results are shown. Tests revealed a linear relationship between the probing force and sensor output (resistance change), and the force vs. deflection. From this relationship, the force constant of the cantilever was calculated to 3.45 N/m with a standard deviation of 0.01 N/m. It shows that there is a big difference between measured and nominal spring constant of 1 N/m provided by the manufacturer s specifications.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.12
• /
• pp.2276-2280
• /
• 2011

An indium-tin-oxide (ITO) is normally used as a substrate in organic photovoltaic cells. We examined the effects of an oxygen ($O_2$) plasma treatment on the electrical properties of an organic photovoltaic cell. Experiments with four-point probe method and atomic force microscope revealed the lowest surface resistance of 17.64 ${\Omega}$/sq and the lowest average surface roughness of 1.39 nm at the plasma treatment power of 250 W. A device structure of ITO/CuPc/$C_{60}$/BCP/$Cs_2CO_3$/Al was fabricated by thermal evaporation with and without the plasma treated ITO substrate. It was found that the power conversion efficiency of the cell with the plasma treated ITO is 65 % higher than the one without the plasma treated ITO.

• Transactions on Electrical and Electronic Materials
• /
• v.11 no.6
• /
• pp.271-274
• /
• 2010

We examined the tunneling current behaviors of magnetic tunneling junction (MTJ) cells utilizing conductive atomic force microscopy (AFM) interfaced with an external magnetic field generator. By introducing current through coils, a magnetic field was generated and then controlled by a current feedback circuit. This enabled the characterization of the tunneling current under various magnetic fields. The current-voltage (I-V) property was measured using a contact mode AFM with a metal coated conducting cantilever at a specific magnetic field intensity. The obtained magnetoresistance (MR) ratios of the MTJ cells were about 21% with no variation seen from the different sized MTJ cells; the value of resistance $\times$ area (RA) were 8.5 K-12.5 K $({\Omega}{\mu}m^2)$. Since scanning probe microscopy (SPM) performs an I-V behavior analysis of ultra small size without an extra electrode, we believe that this novel characterization method utilizing an SPM will give a great benefit in characterizing MTJ cells. This novel method gives us the possibility to measure the electrical properties of ultra small MTJ cells, namely below $0.1\;{\mu}m\;{\times}\;0.1\;{\mu}m$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.323-323
• /
• 2012

We present ferroelectricity of Bi-doped ZnO film probed by piezoresponse force microscopy (PFM), which is one of the Scanning Probe Microscopy techniques. Perovskite ferroelectrics are limited to integration of devices into semiconductor microcircuitry due to hard adjusting their lattice structure to the semiconductor materials. Transition metal doped ZnO film is one of the candidate materials for replacing the perovskite ferroelectrics. In this study, ferroelectric characteristics of the Bi-doped ZnO grown by pulsed laser deposition were probed by PFM. The polarization switching and patterning of the ZnO films were performed by applying DC bias voltage between the AFM tips and the films with varying voltages and polarity. The PFM contrast before and after patterning showed clearly polarization switching for a specific concentration of Bi atoms. In addition, the patterned regions with nanoscale show clearly the local piezoresponse hysteresis loop. The spontaneous polarization of the ZnO film is estimated from the local piezoresponse based on the comparison with LiNbO3 single crystals.