• Journal of the Microelectronics and Packaging Society
• /
• v.24 no.3
• /
• pp.71-76
• /
• 2017

The electrical behavior and flexibility of the screen printed Ag circuits were investigated with infrared radiation sintering times and sintering temperatures. Electrical resistivity and radio frequency characteristics were evaluated by using the 4 point probe measurement and the network analyzer by using cascade's probe system, respectively. Electrical resistivity and radio frequency characteristics means that the direct current resistance and signal transmission properties of the printed Ag circuit. Flexibility of the screen printed Ag circuit was evaluated by measuring of electrical behavior during IPC sliding test. Failure mode of the Ag printed circuits was observed by using field emission scanning electron microscope and optical microscope. Electrical resistivity of the Ag circuits screen printed on Pl substrate was rapidly decreased with increasing sintering temperature and durations. The lowest electrical resistivity of Ag printed circuit was up to $3.8{\mu}{\Omega}{\cdot}cm$ at $250^{\circ}C$ for 45 min. The crack length arisen within the printed Ag circuit after $10{\times}10^4$ sliding numbers was 10 times longer than that of after $2.5{\times}10^4$ sliding numbers. Measured insertion loss and calculated insertion loss were in good agreements each other. Insertion loss of the printed Ag circuit was increased with increasing the number of sliding cycle.

• Research in Plant Disease
• /
• v.10 no.4
• /
• pp.217-226
• /
• 2004

One hundred isolates of Magnaporthe grisea from Korea and China were characterized for pathogenicity using eight Korean differential varieties(KDV), six Chinese differential varieties(CDV) and six near isogenic lines(NILs) developed in China. The restriction length polymorphism of M. grisea isolates from each country also was analyzed using MGR586 as a probe. One hundred Korean isolates classified into 17 races on KDV were grouped into 29 pathotypes on Chinese near isogenic lines(NILs). Virulence of 46% of Korean isolates against all the six Chinese NILs indicated that the current six Chinese NILs alone was not enough to be used as differential varieties in Korea. Especially, susceptibility of the BL1 carrying resistance gene Pi-b to 70% of tested Korean isolates suggested that BL1(Pi-b) may not be a useful resistance source to Korean blast. Based on the virulence assays of M. grisea populations from each country were divided into two groups. About 50% of Chinese isolates showed similarity to the 30% of the Korean isolates. Especially, the isolates from northern part of China, where Japonica rice cultivars were grown, showed high similarity to the Korean isolates, while isolates from southern part of China, where Indica rice were mainly grown, showed low similarity to Korean isolates. The genome RFLPs of Korean isolates were quite different from those of southern part of China using MGR586 as a probe. These data indicated that the physiological and genetical characteristics of M. grisea population might be determined by strong interaction with cultivated rice.

• Journal of Korean Society of Transportation
• /
• v.23 no.5 s.83
• /
• pp.135-146
• /
• 2005

Up to now studies on the fusion of travel time from various detectors have been conducted based on the variance raito of the intermittent data mainly collected by GPS or probe vehicles. The fusion model based on the variance ratio of intermittent data is not suitable for the license plate recognition AVIs which can deal with vast amount of data. This study was carried out to develop the fusion model based on travel time acquired from the license plate recognition AVIs and the point detectors. In order to fuse travel time acquired from the point detectors and the license plate recognition AVIs, the optimized fusion model and the proportional fusion model were developed in this study. As a result of verification, the optimized fusion model showed the superior estimation performance. The optimized fusion model is the dynamic fusion ratio estimation model on real time base, which calculates fusion weights based on real time historic data and applies them to the current time period. The results of this study are expected to be used effectively for National Highway Traffic Management System to provide traffic information in the future. However, there should be further studies on the Proper distance for the establishment of the AVIs and the license plate matching rate according to the lanes for AVIs to be established.

• Journal of the Korean Society of Radiology
• /
• v.11 no.7
• /
• pp.571-578
• /
• 2017

Bubbles are generated by the boiling of the cooling water when an accident occurs in the reactor and then in order to measure the void fraction, the Optical Fiber Probe(OFP) and optical camera are used in thermal hydraulic safety research. However, such an optical method is not suitable for measuring the void fraction in a $17{\times}17$ array of fuel rods due to the geometrical limitations. This study was conducted as a preliminary study using x-ray system and various phantoms before applying to rod bundles. Through radiographic and tomographic experiments, the tube voltage of the x-ray generator was 130 kVp and the tube current was 1 mA. In addition, it is possible to measure the hole of 1mm in size visually through the bubble resolution phantom, and it is confirmed that the contrast is relatively decreased in the inside of the freon in the case of the contrast evaluation using the road phantom. However, we could obtain good image without distortion when reconstructing the image. Bubble generation phantom experiments were used to confirm the flow direction of the bubbles and to acquire tomography images. The image J tool was used to measure the void fraction of 18 % for a single tomography image. This study has carried out previous researches for the measurement of the bubble rate around the nuclear fuel and could be used as a basic research for continuous research.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 1999.10a
• /
• pp.49-49
• /
• 1999

In this study, $Cl_2/BCI_3$ magnetized inductively coupled plasmas (MICP) were used to etch GaN and the effects of magnetic confinements of inductively coupled plasmas on the GaN etch characteristics were investigated as a function of $Cl_2/BCI_3$. Also, the effects of Kr addition to the magnetized $Cl_2/BCI_3$ plasmas on the GaN etch rates were investigated. The characteristics of the plasmas were estimated using a Langmuir probe and quadrupole ma~s spectrometry (QMS). Etched GaN profiles were observed using scanning electron microscopy (SEM). The small addition of $Cl_2/BCI_3$ (10-20%) in $Cl_2$ increased GaN etch rates for both with and without the magnetic confinements. The application of magnetic confinements to the $Cl_2/BCI_3$ inductively coupled plasmas (ICP) increased GaN etch rates and changed the $Cl_2/BCI_3$ gas composition of the peak GaN etch rate from 10% $BCI_3$ to 20% $BCI_3$. It also increased the etch selectivity over photoresist, while slightly reducing the selectivity over $Si0_2$. The application of the magnetic field significantly increased positive $BCI_2{\;}^+$ measured by QMS and total ion saturation current measured by the Langmuir probe. Other species such as CI, BCI, and CI+ were increased while species such as $BCl_2$ and $BCI_3$ were decreased with the application of the magnetic field. Therefore, it appears that the increase of GaN etch rate in our experiment is related to the increased dissociative ionization of $BCI_3$ by the application of the magnetic field. The addition of 10% Kr in an optimized $Cl_2/BCI_3$ condition (80% $Cl_2/$ 20% $BCI_3$) with the magnets increased the GaN etch rate about 60%. More anisotropic GaN etch profile was obtained with the application of the magnetic field and a vertical GaN etch profile could be obtained with the addition of 10% Kr in an optimized $Cl_2/BCI_3$ condition with the magnets.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.3B
• /
• pp.380-389
• /
• 2010

Since the internet is intend to be the best effort service, the system that stream a large amount of high quality medias need a techniques to overcome the network status for implementation. In this paper, we design and implement a method that estimate quickly whether network permits the needed bandwidth of media and a method that control QoS through that. Presented system uses Relative One-Way Delay(ROWD) trend in the case of the former, and leverages temporal encoding among Scalable Video Coding(SVC) that is apt to apply real time comparatively in the case of the latter. The streaming server classifies the medias by real time to several rates and begins transmission from top-level and is reported ROWD trend periodically from the client. In case of the server reported only 'Increase Trend', the sever decides that the current media exceeds the available bandwidth and downgrades the next media level. The system uses probe packet of difference quantity of the target level and the present level for upgrading the media level. In case of the server reported only 'No Increase Trend' by the ROWD trend response of the probe packet from client, the media level is upgraded. The experiment result in a fiber to the home(FTTH) environment shows progress that proposed system adapts faster in change of available bandwidth and shows that quality of service also improves.

• Journal of the Korean Magnetics Society
• /
• v.17 no.4
• /
• pp.156-161
• /
• 2007

To develop array magnetic sensors, specular-type giant magnetoresistive- spin valve (GMR-SV) film of Glass/Ta(5)MiFe(7)/IrMn(10)NiFe(5)/$O_2$/CoFe(5)/Cu(2.6)/CoFe(5)/$O_2$/NiFe(7)/Ta(5)(nm) was deposited by using a high-vacuum sputtering system. One of 15 way sensors in the area of $8{\times}8mm^2$ was Patterned a size of $20{\times}80{\mu}m^2$ in multilayer sample by Photo-lithography. All of 15 sensors with Cu electrodes were measured a uniform magnetic properties by 2-probe method. The highest magnetic sensitivity of MR and output voltage measured nearby an external magnetic field of 5 Oe were MS = 0.5%/Oe and ${\triangle}$V= 3.0 mV, respectively. An easy-axis of top-free layers of $CoFe/O_2/NiFe$ with shape anisotropy was perpendicular to one of bottom-pinned layers $IrMn/NiFe/O_2/CoFe$. When the sensing current increased from 1 mA to 10 mA, the output working voltage uniformly increased and the magnetic sensitivity was almost stable to use the nano-magnetic devices with good sensitive properties.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.27 no.4
• /
• pp.299-304
• /
• 2007

There are to be some cracks on the material degradation part or the stress concentration parts of the main members, which carry on over-loads, of structures. Because these cracks can be used to evaluate the structural health status, it is important to monitor the crack growth for maintaining the structural safety. In this study, the fiber Bragg grating sensor with a drop ball was developed as a sensor for crack growth detection of an existing crack. The crack growth detection sensor was constructed with three parts: a probe part, a wavelength controling light source and receiver part, and an impact part. The probe part was just formed with a fiber Bragg grating optical fiber The wavelength controling light source part was composed of a current supplying circuit, a DFB laser diode, and a TEC controling circuit for wavelength control. Also, the impact part was just implemented by dropping a steel ball. The performance of this sensor was confirmed by the experiments of the crack detection with an aluminum plate having one existing crack. According to these experiments, the difference of the sensor signal outputs was correlated with the crack length. So, it was confirmed that this sensor could be applied to monitor the crack growth.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.28 no.4
• /
• pp.339-345
• /
• 2008

The heat exchanger tube in nuclear power plants is mainly fabricated from nonferromagnetic material such as a copper, titanium, and inconel alloy, but the moisture separator & reheater tube in the turbine system is fabricated from ferromagnetic material such as a carbon steel or ferrite stainless steel which has a good mechanical properties in harsh environments of high pressure and temperature. Especially, the moisture separator & reheater tubes, which use steam as a heat transfer media, typically employ a tubing with integral fins to furnish higher heat transfer rates. The ferromagnetic tube typically shows superior properties in high pressure and temperature environments than a nonferromagnetic material, but can make a trouble during the normal operation of power plants because the ferrous tube has service-induced damage forms including a steam cutting, erosion, mechanical wear, stress corrosion cracking, etc. Therefore, nondestructive examination is periodically performed to evaluate the tube integrity. Now, the remote field testing(RFT) technique is one of the solution for examination of ferromagnetic tube because the conventional eddy current technique typically can not be applied to ferromagnetic tube such as a ferrite stainless steel due to the high electrical permeability of ferrous tube. In this study, we have designed RFT probes, calibration standards, artificial flaw specimen, and probe pusher-puller necessary for field application, and have successfully carry out RFT examination of the moisture separator & reheater tube of nuclear power plants.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.125-126
• /
• 2010

플라즈마 아킹은 PECVD, 플라즈마 식각 그리고 토카막과 같은 플라즈마를 이용하는 여러 공정과 연구 분야에서 문제점을 야기시켜왔다. 하지만, 이에 대한 연구는 아킹 현상의 불규칙성과 과도적인 행동으로 인해 미비한 상태이다. 특히, RF 방전에서의 아킹 연구는 DC 방전에서의 아킹 연구에 비해 많이 부족한 것이 현실이다. 플라즈마 아킹은 집단전자방출(collective electron emission)에 의한 스파크 방전(spark discharge)현상이다. 집단전자방출은 전계방출(field emission)이나 플라즈마와 쉬스를 두고 인접한 표면위에서의 유전분극(dielec emission)에 의해 발생한다. 이렇게 방출된 집단 전자들은 쉬스에서 가속되어 에너지를 얻게 되고 원자와의 충돌로 전자 아발란체를 일으킨다. 이렇게 배가된 전자들은 아킹 스트리머(arcing streamer)를 형성하게 되고 아킹 발생 시 높은 전류와 공정 실패의 원인이 된다. 우리는 $30cm{\times}20cm$ 크기의 사각 전극을 위 아래로 가진 챔버에서 Ar 가스를 RF(13.56 MHz)파워를 이용해 방전시켰다. 방전 전압과 전류는 파워 전극 압단에서 High voltage probe (Tektronix P6015A)와 Current probe (TCPA300 + TCP312)를 이용해 측정했다. 플라즈마 아킹시 변하는 플라즈마 플로팅 포텐셜은 챔버 중앙에 위치한 랑뮈프 프로브에 의해 측정되고 챔버 옆의 뷰포트 앞에 위치한 PM-tube를 이용해 아킹시 변하는 광량을 측정한다. RF 방전에서의 플라즈마 아킹은 아킹시 플로팅 포텐셜의 변화에 의해 크게 세부분으로 나눌 수 있다. 아킹 발생과 동시에 급격히 감소하는 감소부분 (약 2us) 그리고 감소한 포텐셜이 유지되는 유지부분 (약 0~10ms) 그리고 감소했던 포텐셜이 서서히 원래 상태로 회복되는 회복부분(약 100 us)이다. 아킹 초기시 방출된 집단 전자들과 원자들간의 충돌에 의해 형성된 아킹 스트리머는 플라즈마 전체를 단락시키게 되고 이로 인해 플로팅 포텐셜은 급격히 감소하게 된다. 이렇게 감소한 플로팅 포텐셜은 아킹 스트리머가 유지되는 한 계속 감소한 상태를 유지하게 된다. 그리고 플라즈마를 섭동했던 아킹 스트리머가 중단되면 플라즈마는 섭동전의 원래 상태로 돌아가려 하기 때문에 플로팅 포텐셜은 서서히 증가하면서 원래 상태로 회복된다. 플라즈마 아킹 발생시 생성되는 아킹 스트리머는 순간적으로 많은 전자들을 국소적으로 생성하게 되고 이 전자들에 의해 광량이 순간적으로 증가하게 된다. PM-tube (750.4 nm)에 의해 측정된 아킹시 광량은 정상방전 상태의 두배 가량이 된다. 그리고 이 순간적으로 증가된 광량은 시간이 지남에 따라 감소하게 되고 정상방전 일때의 광량이 된다. 광량이 증가한 후 정상방전 상태의 광량에 이르는 부분은 플로팅 포텐셜이 감소한 상태에서 유지되는 부분과 일치하고 이는 플로팅 포텐셜의 유지부분동안 아킹 스트리머가 발생하고 있다는 간접적인 증거가 된다. 그리고 정상 방전 상태 일때의 광량이 되면 아킹 스트리머가 중단되었다는 것이므로 그 시점부터 플로팅 포텐셜은 정산 방전상태 일 때의 포텐셜로 복구되기 시작한다. 이처럼 PM-tube를 이용한 아킹 광량 측정은 아킹 스트리머를 간접적으로 측정하게 하고 아킹 스트리머를 이용해 아킹시의 플로팅 포텐셜의 변화를 설명하게 해 준다. 응용적인 측면에서 아킹 광량 측정을 이용한 아킹 판독은 방전 전류와 방전 전압과 같은 전기적 신호를 이용한 아킹 판독에 비해 여러가지 장점을 가진다. 우선, 전기적 신호를 이용한 아킹 판독처럼 매칭 회로나 플라즈마를 섭동시키지 않는다. 그리고 원하는 부분의 아킹만을 판독하는 것도 가능하며 photo-diode를 이용할 경우 전기적 신호를 이용하는 것에 비해 경제적으로 유리하다.