• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.34 no.5
• /
• pp.39-48
• /
• 2002

The water retention of coating colors can be accurately measured by devices such as an AA-GWR water retention meter whose principle of measurement Is based on pressure filtration of coatings under an externally applied air pressure over a certain period of time. It was hypothesized that such devices could be also used to determine the immobilization solids (IMS) of coating colors by determining a sudden drop in the rate of dewatering, that is, a sudden change in the drainage curves. To test this hypothesis, the immobilization solids of coating colors containing various thickeners and water retention additives at different levels were first accurately measured by a modified immobilization tester based on the well-known gloss drop method, and then their values were compared with those obtained by an AA-GWR water retention tester. They agreed very well and showed that the standard deviation is only 0.14% in the IMS points between both methods. This good agreement was not surprising because both test methods are based on the same end-point, that is, the immobilization solids point at which menisci begin to form at the coating surface. Theoretical considerations supporting this new method for measuring the immobilization solids of coating colors are presented and some recommendations for the test method are discussed. Also, the effect of various thickeners and water retention additives on the properties and printability of coated papers is discussed.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.38 no.5 s.118
• /
• pp.38-46
• /
• 2006

Many researches for extensive uses of Hanji have been performed. With the advent of an information-oriented age, the development of Hanji which is printable has been considered as a new field of study. Since Hanji has many drawbacks in comparison with common printing papers, that is, rougher surface, huger absorption of ink and lower physical properties and printabilities. Improving the properties and printabilities of Hanji is therefore the most important work to deal with. This study was conducted to find out useful mixed agents for surface sizing suitable for printable Hanji. Four surface sizing agents (CMC, corn starch, PYA, AKD) were applied for mixture in this study. The physical properties of surface sized Hanji were measured. Results obtained were as follows. Based on designated agents according to concentration, each of the mixed agents was prepared. The kinds of mixture were corn starch (3%) and PVA (5%), corn starch (3%) and AKD (0.1%), corn starch (3%) and CMC (1%), AKD (0.1%) and CMC (1%), AKD (0.1%) and PVA (5%), CMC (1%) and PVA (5%). Each mixed surface sizing agents was included with these ratios (100:0, 90:10, 70:30, 50:50, 30:70, 10:90, 0:100) respectively. All the mixed agents improved the physical properties and printabilities of Hanji. Among them, mixed agent of CMC (1%) and corn starch (3%) with 90:10 ratio is superior to the others for not only smoothness but also ink printability. In view of the result achieved, it is regarded that it can be fit for using Hanji as a printing paper and turned out to be a good contribution to Hanji industry.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2006.06b
• /
• pp.215-225
• /
• 2006

Today's requirements for print-press runnability and print quality demand an optimised absorption and adhesion of printing ink on the paper surface. Modern coating concepts for high glossing offset grades use ultra fine pigments, whereas binder level has continuously been decreased to a minimum in recent years to achieve the highest possible sheet gloss development and for economical reasons. Both the ultra fine pigments and the reduced binder levels lead in many cases to a faster ink setting rate. On the other hand, matt paper grades use relatively coarse pigments leading to a slow ink setting compared to the high glossing papers. Both too fast and too slow ink setting properties implicate drawbacks in print quality and print press runnability. The mechanisms behind the interactions between ink and coating have been presented in many previous publications. The purpose of this study was to determine and quantify how the ink setting rate is influenced by pigment system (GCC and GCC/clay blends), latex level and latex properties in the topcoat of double coated sheet fed offset paper. The roles of binder level and type in the precoat were also assessed. The effect of calendering (temperature and pressure) was studied with one formulation. The resulting ink setting characteristics were tested using three different laboratory testing instruments. The correlation amongst the different laboratory testing methods is discussed. The results show that by varying the latex properties, the pigment system and/or latex addition level, the ink tack development of ink applied to a topcoat pigment system can be significantly influenced. It can be slowed down as often desired with ultra fine pigments or speeded up in the case of coarse pigments. There was no visible effect on the ink setting rate by using different binder systems in the precoat..

• The Korean Journal of Quaternary Research
• /
• v.14 no.1
• /
• pp.73-86
• /
• 2000

Abstracts and papers written in Korean presented in the 26th meeting of the Korea Quaternary Association held at Kongju University in November, 1999 are reviewed with an attention to such as writing well in Korean. Paragraphs and sentences of manuscripts are dotted with words and expressions of foreign languages such as Japanese, Chinese, English, and very long sentences. Undesirable expressions include also contradictory meanings, difficult expressions using Chinese characters, and incorrect sentences and wordings, and etc. Some recommendations for good manuscripts written in Korean are suggested. They include reading of science books for general readers and drilling for writing good manuscripts in Korean. Writing manuscripts in ample time, discussions with colleagues, and open-minded mentality of authors to accept critics are included in the drilling for writing good manuscripts. Editorial board should also check the manuscripts before printing.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.41 no.1
• /
• pp.24-29
• /
• 2009

The use of fluorescent whitening agents (FWAs) increases as the demand for the whiter and brighter printing papers increases. FWAs are used as internal and surface treatment chemicals. FWAs that are not used properly in the papermaking process, however, remain in the process water and may demage the paper quality and processes. In this study, a new idea to eliminate FWAs from the process water, consisted of the floc formation of FWAs with cationic chemicals, such as cationic polyelectrolytes and alum, and the removal of the floc by screening or sedimentation, was proposed. Flocculation of FWAs, that is the first step to remove FWAs from the process water, was investigated using turbidity and particle size measurement. Relationship between turbidity and particle size showed that the turbidity could reflect the particle size change of FWA flocs and was proper for the evaluation of flocculation phenomena. Poly-DADMAC was more efficient than PEI to induce the flocculation of FWAs. Alum was effective chemical for the flocculation and sedimentation of FWAs.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.45 no.1
• /
• pp.59-66
• /
• 2013

Fillers have been used for printing paper to improve printability, sheet formation and optical properties and to reduce production costs by replacing expensive wood pulps. However, an increased filler content will decrease paper strength because filler particles interfere with fiber-fiber bonding. In order to increase filler content without sacrificing too much paper strength in high filler content papers, the surface of precipitated calcium carbonate (PCC) has been modified by adsorbing anionic polyacrylamide and cationic starch in series. The adsorbed polymer layers would enhance interactions between the filler surface and the fiber surface, improving internal bonding. It was found that the modified PCC increased paper strength at a given filler content compared to the coventional method. Negligible differences in optical properties and formation of paper, filler and fines retention and drainage on the wire section were observed between the modified and the conventional PCC. However, the decreased bulk of paper was observed when the modified PCC was used.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.41 no.5
• /
• pp.825-839
• /
• 2017

Generative Art (also called as the art of the algorithm) creates unexpected results, moving autonomously according to rules or algorithms. The evolution of digital media in art, which tries to seek novelty, increases the possibility of new artistic fields; subsequently, this study establishes the basis for new design approaches by analyzing visual cases of Generative Art that have emerged since the 20th century and characteristics expressed on fashion. For the methodology, the study analyzes fashion designs that have emerged since 2000, based on theoretical research that includes literature and research papers relating to Generative Art. According to the study, expression characteristics shown in fashion, based on visual properties of Generative Art, are as follows. First, abstract randomness is expressed with unexpected coincidental forms using movements of a creator and properties of materials as variables in accordance to rules or algorithms. Second, endlessly repeated pattern imitation expresses an emergent shape by endless repetition created by a modular system using rules or 3D printing using a computer algorithm. Third, the systematic variability expresses constantly changing images with a combination of system and digital media by a wearing method. It is expected that design by algorithm becomes a significant method in producing other creative ideas and expressions in modern fashion.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.24 no.1
• /
• pp.59-66
• /
• 2006

We studied on the effects of the enzyme treatment of pulp fiber on physical properties of coated paper were elucidated using four types of enzymes. The results of this study showed that the blank in which enzyme was not treated showed the highest $St{\ddot{o}}ckigt$ and Hurcules sizing degrees. And when the enzyme treated base paper was used for coating, the coated paper has average 5.7 % higher gloss and whiteness than when untreated base paper was used. Brightness showed 0.12 % higher results with the enzyme treated base papers than the blank while it is considered to show similar trends. Whiteness of coated paper was not influenced by the enzyme treatments but by the properties of coating color. Coated paper whose base paper was enzyme treated showed improved roughness while smoothness of those samples except the ${\beta}$-Glucosidase treated one was relatively low due to the high fines content. Also the coated paper whose base paper was not enzyme treated showed high porosity.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.32 no.4
• /
• pp.1-9
• /
• 2000

As the speed of the paper machine and printing press increases, the dependency of the production efficiency upon the frequency of web break increases. It is believed that flaw or crack that presents in paper is one of the most important for web break. Runnability of papers on the paper machine could be evaluated by measuring fracture toughness. In this paper the effect kof beating and pressing on the runnability was investigated using handsheets made from softwood bleached kraft pulp beaten to different freeness. Pressing pressure was also varied to obtain different levels of sheet consolidation. Density, tensile strength, and J-integral of the handsheets were evaluated. For measuring J-integral either a single specimen method or RPM method was employed. Results showed that the density and tensile strength were improved as beating and pressing increased because of increased interfiber bonding. J-integral increased with beating until the CSF reached 400mL. No significant difference in J-integral, however, was observed afterward with the increase of beating. And it appeared to be due to acceleration of the stress concentration around the crack that exists on the fiber wall of the sheet when cracks exists.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.32 no.4
• /
• pp.74-80
• /
• 2000

A series of studies on nitric-acid pulping of municipal recycled waste papers were carried out to substitute the bleached chemical pulp imported for producing printing paper as well as to use its solidified spent-liquor as fertilizer. The first experiment was carried out to find the optimum treatment conditions such as pulp consistency, nitric acid charge and temperature in $HNO_3$-alkali pulping process. The results obtained were as follows: 1. Some selective delignification of OCC pulp was conducted by $HNO_3$-alkali process. The higher the temperature and concentration of nitric acid, the lower the pulp yield and kappa number of treated pulp. while its brightness was increased. 2. The higher consistency required the stronger mixing in case of more than 5% pulp. 3. In the laboratory, the suitable $HNO_3$-treating condition seemed to be less than 6% consistency, lower than 500% $HNO_3$charge on pulp and lower than $100^{\circ}C$ in cooking temperature. 4. The spent liquor with 1.77% N-content seemed to be slow-release nitrogen fertilizer suitable for agriculture.