• Journal of the Korean Society of Industry Convergence
• /
• v.20 no.2
• /
• pp.187-194
• /
• 2017

This study examined the validity and reliability of the thermal safety design, in order to maintain the heat generated from integrated circuit (IC) chips in the converter, condenser, resistor, and transistor (which are considered as heat sources for thermoelectric devices with a printed circuit board) below target levels during the process of developing a control board and a main power board. The study analyzed the heat generation and dissipation characteristics of the entire printed circuit board (PCB) model to examine its thermal safety.

• Journal of Institute of Control, Robotics and Systems
• /
• v.8 no.6
• /
• pp.514-523
• /
• 2002

Feeder arrangement is an important element of process planning for printed circuit board assembly systems. This paper newly proposes a feeder arrangement method for multihead-gantry chip mounters. The multihead-gantry chip mounters are very popular in printed circuit board assembly system, but the research has been mainly focused on single-head-gantry chip mounters. We present an integer programming formulation for optimization problem of multihead-gantry chip mounters, and propose a heuristic method to solve the large NP-complete problem in reasonable time. Dynamic programming method is then applied to feeder arrangement optimization to reduce the overall assembly time. Comparative simulation results are finally presented to verify the usefulness of the proposed method.

• Journal of IKEEE
• /
• v.22 no.3
• /
• pp.882-885
• /
• 2018

Recently, signal integrity on PCB (printed circuit board) becomes very important as the system operation speed increases. So far, PCB is customarily designed to minimize area and cost. However, ultra-high-speed PCB often fail to operate properly, unless it is precisely and carefully designed considering dielectric characteristics, line width, line spacing, and impedance matching. This paper surveys many problems in ultra-high-speed PCB and various design methods to mitigate them.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.3
• /
• pp.472-478
• /
• 2012

The inspection machine in PCB (printed circuit board) assembly line checks assembly errors by inspecting the images inside of the component inspection region. The component inspection region consists of region of component package and region of soldering. It is necessary to extract the regions automatically for auto-teaching system of the inspection machine. We propose an image segmentation method to extract the component inspection regions automatically from images of PCB. The acquired image is transformed to HSI color model, and then segmented by several regions by clustering method. We develop a modified K-means algorithm to increase the accuracy of extraction. The heuristics generating the initial clusters and merging the final clusters are newly proposed. The vertical and horizontal projection is also developed to distinguish the region of component package and region of soldering. The experimental results are presented to verify the usefulness of the proposed method.

• International Journal of Quality Innovation
• /
• v.2 no.2
• /
• pp.69-92
• /
• 2001

The laser-assisted seeding (LAS) process has potential to replace conventional electroless copper plating in Printed Circuit Board (PCB) manufacturing since it combines the steps of laser drilling and plating into one single process. In the LAS process, the single extra LAS step can metallize a microvia. Thus, the process steps can be greatly reduced and the productivity enhanced, but also the high aspect ratio microvias can be metallized. The objectives of this paper are to study the LAS copper thickness within PCB microvias and the thermal reliability of the microvias produced by this process. It was found that results were satisfactory in both the reliability test and also the LAS copper thickness which both comply with IPC standard, the copper thickness produced by the LAS process is sufficient for subsequent electro-plating process. The reliability of the microvias produced by LAS process is acceptable which are free from any voids, corner cracks, and distortion in the plated copper.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.78-81
• /
• 2002

Printed Circuit Boards for satellite are composed of multi-layered copper plate and glass epoxy. Each copper layer have the complicated and different pattern to operate correctly for its mission. Especially. copper layer give effect on the PCB stiffness seriously. But It can make more complicate to predict the exact stiffness of PCB. In KOMPSAT-2 program, too many type of PCB are used for each electronic unit, and they have different type of pattern of copper layer. Solar array regulator has two type of PCB and it will be considered for this study. In this study. we calculate the PCB board stiffness of KOMPSAT-2 SAR unit considering the concept of simplified representative volume element. It will be correlated with the test results under KOMPSAT-2 vibration environmental condition to increase the reliability of this study.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.1491-1494
• /
• 2008

Typically internal mobile LCD display modules are connected to the mobile product baseband PCB with flexible printed circuit board equipped with board-to-board connector. This solution has a drawback of limiting the product concept work to certain solutions that are based on connector size, location, flexible PCB length, bending, etc. in the display module. Also flexible printed circuit board based solutions are not completely optimized from reliability point of view, causing flex circuit board breakings. For the external displays in the PC or Home entertainment market, the cable solution is too expensive and resource demanding. The wireless solution has obvious advantages over reliability, low cost and flexibility. This paper describes a wireless audio-visual interface solution.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.1
• /
• pp.56-62
• /
• 2013

The laser cutting process which is flexible and rapid usually provides a better result in cutting of flexible printed circuit boards (FPCB). However, circuit-short by the re-deposition of debris from laser ablation or its heat affect zone (HAZ) on the cutting surfaces can be a problem. A laser cutting process of FPCB in the presence of liquid can minimize these negative effects. The temperature distribution of copper and polymer parts of FPCB was analyzed with numerical simulation and the experimental results were presented to evaluate this process. Generally, laser cutting under liquid has advantages of less re-deposition of carbides and less HAZ on the cutting edges. However, bubble generation and laser beam control through the liquid media should be considered carefully to obtain a successful result.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.20 no.41
• /
• pp.177-188
• /
• 1997

This study describes the important information for establishing Human Computer Interface System for solving the large scale Traveling Saleman Problem in Printed Circuit Board production. Appropriate types and sizes of partitioning of large scale problems are discussed. Optimal tours for the special patterns appeared in PCB's are given. The comparision of optimal solutions of non-Euclidean problems and Euclidean problems shows the possibilities of using human interface in solving the Chebyshev TSP. Algorithm for the large scale problem using described information and coputational result of the practical problem are given.

• 한국전기화학회:학술대회논문집
• /
• 2005.07a
• /
• pp.209-212
• /
• 2005