• Korean Journal of Applied Biomechanics
• /
• v.25 no.2
• /
• pp.157-165
• /
• 2015

Object : The goals of this research were to make Performance Enhanced Model(PE) taken the largest performance index (PI) through artificial variation of principle components calculated by principle component analysis for trial data, and to verify the effect through comparing kinematic factors between trial data (Raw) and PE. Method : Ten subjects (5 men, 5 women) were recruited and 80% of their maximal record was considered. The PI is a regression equation. In order to develop PE, we extracted Principle components from trial position data (by Principle Components Analysis (PCA)). Before PCA, we made 17 position data to 3 row matrix according to components. We calculated 3 eigen value (principle components) through PCA. And except Y (medial-lateral direction) component (because motion of Y component is small), principle components of X (anterior-posterior direction) and Z (vertical direction) components were changed as following. Changed principle components = principle components + principle components ${\times}$ k. After changing the each principle component, we reconstructed position data using the changed principle components and calculated performance index (PI). A Paired t-test was used to compare Raw data and Performance Enhanced Model data. The level of statistical significance was set at $p{\leq}0.05$. Result : The PI was significantly increased about 12.9kg at PE ($101.92{\pm}6.25$) when compared to the Raw data ($91.29{\pm}7.10$). It means that performance can be increased by optimizing 3D positions. The difference of kinematic factors as follows : the movement distance of the bar from start to lock out was significantly larger (about 1cm) for PE, the width of anterior-posterior bar position in full phase was significantly wider (about 1.3cm) for PE and the horizontal displacement toward the weightlifter after beginning of descent from maximal height was significantly greater (about 0.4cm) for PE. Additionally, the minimum knee angle in the 2-pull phase was significantly smaller (approximately 2.7cm) for the PE compared to that of the Raw. PE was decided at proximal position from the Raw (origin point (0,0)) of PC variation). Conclusion : PI was decided at proximal position from the Raw (origin point (0,0)) of PC variation). This means that Performance Enhanced Model was decided by similar motion to the Raw without a great change. Therefore, weightlifters could be accept Performance Enhanced Model easily, comfortably and without large stress. The Performance Enhance Model can provide training direction for athletes to improve their weightlifting records.

• Journal of the Korean Statistical Society
• /
• v.29 no.2
• /
• pp.231-245
• /
• 2000

This paper considers a linear regression model with space and time data in where the disturbances follow spatially correlated error components. We provide the best linear unbiased predictor for the one way error components. We provide the best linear unbiased predictor for the one way error component model with spatial autocorrelation. Further, we derive two diagnostic test statistics for the assessment of model specification due to spatial dependence and random effects as an application of the Lagrange Multiplier principle.

• Journal of Applied Reliability
• /
• v.16 no.2
• /
• pp.98-103
• /
• 2016

Purpose: The purpose of this paper is to get a meaningful information for improving manufacturing quality of the products before they are produced in client's manufacturing process. Methods: A variety of data mining techniques have been being used for wide range of industries from process data in manufacturing factories for quality improvement. One application of those is to get meaningful information from process data in manufacturing factories for quality improvement. In this paper, the failure rate at client's manufacturing process is predicted by using the parameters of the characteristics of the product based on PCA (Principle Component Analysis) and regression analysis. Results: Through a case study, we proposed the predicting methodology and regression model. The proposed model is verified through comparing the failure rates of actual data and the estimated value. Conclusion: This study can provide the guidance for predicting the failure rate on the manufacturing process. And the manufacturers can prevent the defects by confirming the factor which affects the failure rate.

• Journal of Environmental Impact Assessment
• /
• v.23 no.3
• /
• pp.187-196
• /
• 2014

The objective of this study is to evaluate and analyze Osu stream watershed water environment system. The data were collected from January 2009 to December 2011 including water temperature, pH, DO, EC, BOD, COD, TOC, SS, T-N, T-P and discharge. The data were used for principle component analysis and factor analysis. The results are as followes. The primary factors obtained from both the principal component analysis and the factor analysis were BOD, COD, TOC, SS and T-P. Once principal component analysis and factor analysis have been performed with the collected data and then the results will be applied to both simple regression model and multiple regression model. The regression model was developed into case 1 using concentrations of water quality parameters and case 2 using delivery loads. The value of the coefficient of determination on case 1 fell between 0.629 and 0.866; this was lower than case 2 value which fell between 0.946 and 0.998. Therefore, case 2 model would be a reliable choice.The coefficient of determination between the estimated figure using data which was developed to the regression model in 2012 and the actual measurement value was over 0.6, overall. It can be safely deduced that the correlation value between the two findings was high. The same model can be applied to get TOC concentrations in future.

• The KIPS Transactions:PartD
• /
• v.9D no.1
• /
• pp.75-80
• /
• 2002

Putnam develops SLIM (Software LIfecycle Management) model based upon the assumption that the manpower utilization during software project development is followed by a Rayleigh distribution. To obtain the manpower distribution, we have to be estimate the total development effort and difficulty ratio parameter. We need a way to accurately estimate these parameters early in the requirements and specification phase before investment decisions have to be made. Statistical tests show that system attributes are highly correlation (redundant) so that Putnam discards one and get a parameter estimator from the other attributes. But, different statistical method has different system attributes and presents different performance. To select the principle system attributes, this paper uses the principle component analysis (PCA) instead of Putnam's method. The PCA's results improve a 9.85 percent performance more than the Putnam's result. Also, this model seems to be simple and easily realize.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.1C
• /
• pp.65-71
• /
• 2004

We improved the MLLR speaker adaptation algorithm with reduction of the order of HMM parameters using PCA(Principle Component Analysis) or ICA(Independent Component Analysis). To find a smaller set of variables with less redundancy, we adapt PCA(principal component analysis) and ICA(independent component analysis) that would give as good a representation as possible, minimize the correlations between data elements, and remove the axis with less covariance or higher-order statistical independencies. Ordinary MLLR algorithm needs more than 30 seconds adaptation data to represent higher word recognition rate of SD(Speaker Dependent) models than of SI(Speaker Independent) models, whereas proposed algorithm needs just more than 10 seconds adaptation data. 10 components for ICA and PCA represent similar performance with 36 components for ordinary MLLR framework. So, compared with ordinary MLLR algorithm, the amount of total computation requested in speaker adaptation is reduced by about 1/167 in proposed MLLR algorithm.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.481-482
• /
• 2014

• Journal of Biosystems Engineering
• /
• v.29 no.6 s.107
• /
• pp.539-543
• /
• 2004

The purpose of this study was to develop a real-time sensor for beef freshness. Contents of biogenic amines (BA), saccharides and proteins were highly related with freshness on the beef meats. Relations of those chemical contents and NIR spectra were studied. Tyramine showed the best correlation coefficient at 1250nm. Correlation between VBN (volatile basic nitrogen) and K value, which were both freshness measurement method, was determined by the PCR (principle component regression). The correlation model had the values of $R^2=0.989$ and SEC=1.78, respectively. The model was validated at $R^2=0.963$ and SEP=2.285, respectively.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.1343-1346
• /
• 2005

In the cold rolling mill, coil breakage that generated in rolling process makes the various types of troubles such as the degradation of productivity and the damage of equipment. Recent researches were done by the mechanical analysis such as the analysis of roll chattering or strip inclining and the prevention of breakage that detects the crack of coil. But they could cover some kind of breakages. The prediction of Coil breakage was very complicated and occurred rarely. We propose to build effective prediction modes for coil breakage in rolling process, based on data mining model. We proposed three prediction models for coil breakage: (1) decision tree based model, (2) regression based model and (3) neural network based model. To reduce model parameters, we selected important variables related to the occurrence of coil breakage from the attributes of coil setup by using the methods such as decision tree, variable selection and the choice of domain experts. We developed these prediction models and chose the best model among them using SEMMA process that proposed in SAS E-miner environment. We estimated model accuracy by scoring the prediction model with the posterior probability. We also have developed a software tool to analyze the data and generate the proposed prediction models either automatically and in a user-driven manner. It also has an effective visualization feature that is based on PCA (Principle Component Analysis).

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.9
• /
• pp.3900-3914
• /
• 2012

This study examined the background of the recent global financial crisis and the concept of one of the financial derivatives such as the credit default swap(CDS) or synthetic CDO(collateral debt obligations), given the rapid growing and changing the over-the-counter derivative markets in their volume and structures. In comparison with the previous literature such as the study of Park & Kim (2011), this research empirically performed more thorough and comprehensive investigations to find any financial characteristics or attributes to determine the CDS spreads. Regarding the results obtained from the multiple regression models, the explanatory variables such as STYIELD3, SLOPE, INASSETS, and VOLATILITY, showed their statistically significant effects on all the tested dependent variables(DVs). Another procedure such as the principle component analysis(PCA), was also performed to account for additional IDVs as possible determinants of the dependent variables. Subsequent to this analysis, larger coefficients of each corresponding eigenvector such as BETA, PFT2, GROWTH, STD, and BLEVERAGE were found to be possible financial determinants. For robustness, all the IDVs were employed to be tested in the 'full' regression model with stepwise procedure. As a result, STYIELD3, SLOPE, and VOLATILITY, and BETA showed their statistically significant relationship with all the dependent variables of the CDS spreads.