• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.7 no.4
• /
• pp.613-631
• /
• 2013

Cognitive radio (CR) is proposed as a key solution to improve spectral efficiency and overcome the spectrum scarcity. Spectrum sensing is an important task in each CR system with the aim of identifying the spectrum holes and using them for secondary user's (SU) communications. Several conventional methods for spectrum sensing have been proposed such as energy detection, matched filter detection, etc. However, the main limitation of these classical methods is that the CR network is not able to communicate with its own base station during the spectrum sensing period and thus a fraction of the available primary frame cannot be exploited for data transmission. The other limitation in conventional methods is that the SU data frames should be synchronized with the primary network data frames. To overcome the above limitations, here, we propose a spectrum sensing technique based on blind source separation (BSS) that does not need time synchronization between the primary network and the CR. Moreover, by using the proposed technique, the SU can maintain its transmission with the base station even during spectrum sensing and thus higher rates are achieved by the CR network. Simulation results indicate that the proposed method outperforms the accuracy of conventional BSS-based spectrum sensing techniques.

• Journal of KSNVE
• /
• v.9 no.1
• /
• pp.97-102
• /
• 1999

Structure-borne noise is an important aspect to consider during the design and development of a vehicle. In this work. it was desired to identify the primary paths associated with structure-borne noise generated from the engine and front suspension. An experimental source-path-receiver model was used to characterize the system. A variety of primary sources such as engine. tires or exhaust system generate vibrations of the inner surfaces of the passenger compartment of a vehicle which subsequently radiate noise. The source was characterized by the force acting at the engine-to-body interface. and the path was characterized by pressure over force FRF's. The excitation forces were indirectly determined using dynamic stiffness of rubber mount or the system accelerance matrix. Through these analysis, path contribution diagram which is well expressed primary noise path is obtained.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.10
• /
• pp.2377-2380
• /
• 2009

The treatment of primary amines with amino acids as a CO source in the presence of polyaniline emeraldine salts bring about N-formylation to give the corresponding formamides. This route to N-formylation methodology of primary amine represents the first reported example of a CO-transfer via radical mechanism by highly nanoporous polyaniline emeraldine salts catalyst.

• Nuclear Engineering and Technology
• /
• v.49 no.3
• /
• pp.638-644
• /
• 2017

The importance of developing a source-term assessment technology has been emphasized owing to the decommissioning of Kori nuclear power plant (NPP) Unit 1 and the increase of deteriorated NPPs. We analyzed the behavioral mechanism of corrosion products in the primary system of a pressurized heavy-water reactor-type NPP. In addition, to check the possibility of applying the CRUDTRAN code to a Canadian Deuterium Uranium Reactor (CANDU)-type NPP, the type was assessed using collected domestic onsite data. With the assessment results, it was possible to predict trends according to operating cycles. Values estimated using the code were similar to the measured values. The results of this study are expected to be used to manage the radiation exposures of operators in high-radiation areas and to predict decommissioning processes in the primary system.

• Progress in Medical Physics
• /
• v.13 no.1
• /
• pp.21-26
• /
• 2002

A practical calculation algorithm which calculates the relative output factor(ROF) for irregular shaped electron field has been developed and evaluated the accuracy of the algorithm. The algorithm adapted two-source model, which assumes that the electron dose can be express as sum of the primary source component and the scattered component from the shielding block. Original two-source model has been modified in order to make the algorithm simpler and to reduce the number of parameters needed in the calculation, while the calculation error remains within clinical tolerance range. The primary source is assumed to have Gaussian distribution, while the scattered component follows the inverse square law. Depth and angular dependency of the primary and the scattered are ignored ROF can be calculated with three parameters such as, the effective source distance, the variance of primary source, and the scattering power of the block. The coefficients are obtained from the square shaped-block measurements and the algorithm is confirmed from the rectangular or irregular shaped-fields used in the clinic. The results showed less than 1.0 ％ difference between the calculation and measurements for most cases. None of cases which have bigger than 2.1 ％ have been found. By improving the algorithm for the aperture region which shows the largest error, the algorithm could be practically used in the clinic, since one can acquire the 1011 parameter's with minimum measurements(5∼6 measurements per cones) and generates accurate results within the clinically acceptable range.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• v.22 no.4
• /
• pp.217-239
• /
• 2018

This paper examined the MHD and thermal behavior of unsteady mixed convection flow of a rotating fluid in a porous parallel plate channel in the presence of Hall current and heat source. The exact solutions of the concentration, energy and momentum equations are obtained. The influence of each governing parameter on non dimensional velocity, temperature, concentration, skin friction coefficient, rate of heat transfer and rate of mass transfer at the porous parallel plate channel surfaces is discussed. During the course of numerical computation, it is observed that as Hall current parameter and Soret number at the porous channel surfaces increases, the primary and secondary velocity profiles are increases while the primary and secondary skin friction coefficients are increases at the cold wall and decreases at the heated wall. In particular, it is noticed that a reverse trend in case of heat source parameter.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.37 no.2
• /
• pp.70-76
• /
• 2014

In industrial situation, electronic and electro-mechanical systems have been using different type of batteries in rapidly increasing numbers. These systems commonly require high reliability for long periods of time. Wider application of battery for low-power design as a prime power source requires us knowledge of failure mechanism and reliability of batteries in terms of load condition, environment condition and other explanatory variables. Battery life is an important factor that affects the reliability of such systems. There is need for us to understand the mechanism leading to the failure state of battery with performance characteristic and develop a method to predict the life of such battery. The purpose of this paper is to develope the methodology of monitoring the health of battery and determining the condition or fate of such systems through the performance reliability to predict the remaining useful life of primary battery with load condition, operating condition, environment change in light of battery life variation. In order to evaluate on-going performance of systems and subsystems adopting primary batteries as energy source, The primitive prototype for performance reliability analysis device was developed and related framework explained.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.7 no.2
• /
• pp.271-287
• /
• 2013

We propose a new multipath-based reliable routing protocol on MANETs, Multipath-based Reliable routing protocol with Fast-Recovery of failures (MRFR). For reliable message transmission, MRFR tries to find the most reliable path between a source and a destination considering the end-to-end packet reception reliability of the routes. The established path consists of a primary path that is used to transmit messages, and the secondary paths that are used to recover the path when detecting failures on the primary path. After establishing the path, the source transmits messages through the primary path. If a node detects a link failure during message transmission, it can recover the path locally by switching from the primary to the secondary path. By allowing the intermediate nodes to locally recover the route failure, the proposed protocol can handle the dynamic topological change of the MANETs efficiently. The simulation result using the QualNet simulator shows that the MRFR protocol performs better than other protocols in terms of the end-to-end message delivery ratio and fault-tolerance capability.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.6 no.12
• /
• pp.3081-3099
• /
• 2012

We propose a new multipath-based reliable routing protocol on MANETs, Multipath-based Reliable routing protocol with Fast-Recovery of failures (MRFR). For reliable message transmission, MRFR tries to find the most reliable path between a source and a destination considering the end-to-end packet reception reliability of the routes. The established path consists of a primary path that is used to transmit messages, and the secondary paths that are used to recover the path when detecting failures on the primary path. After establishing the path, the source transmits messages through the primary path. If a node detects a link failure during message transmission, it can recover the path locally by switching from the primary to the secondary path. By allowing the intermediate nodes to locally recover the route failure, the proposed protocol can handle the dynamic topological change of the MANETs efficiently. The simulation result using the QualNet simulator shows that the MRFR protocol performs better than other protocols in terms of the end-to-end message delivery ratio and fault-tolerance capability.

• Nuclear Engineering and Technology
• /
• v.54 no.8
• /
• pp.3073-3084
• /
• 2022

The propagation of radiation source uncertainties in spent nuclear fuel (SNF) cask shielding calculations is presented in this paper. The uncertainty propagation employs the depletion and source term outputs of the deterministic code STREAM as input to the transport simulation of the Monte Carlo (MC) codes MCS and MCNP6. The uncertainties of dose rate coming from two sources: nuclear data and modeling parameters, are quantified. The nuclear data uncertainties are obtained from the stochastic sampling of the cross-section covariance and perturbed fission product yields. Uncertainties induced by perturbed modeling parameters consider the design parameters and operating conditions. Uncertainties coming from the two sources result in perturbed depleted nuclide inventories and radiation source terms which are then propagated to the dose rate on the cask surface. The uncertainty analysis results show that the neutron and secondary photon dose have uncertainties which are dominated by the cross section and modeling parameters, while the fission yields have relatively insignificant effect. Besides, the primary photon dose is mostly influenced by the fission yield and modeling parameters, while the cross-section data have a relatively negligible effect. Moreover, the neutron, secondary photon, and primary photon dose can have uncertainties up to about 13%, 14%, and 6%, respectively.