• Journal of the Korean Geotechnical Society
• /
• v.27 no.10
• /
• pp.13-23
• /
• 2011

Bearing capacity of pile foundations in cold region is dominated by adfreeze bond strength between surrounding soil and pile perimeter. It denotes that adfreeze bond strength is the most important design parameter for foundations in cold region. Adfreeze bond strength is affected by various factors like 'soil type', 'frozen temperature', 'normal stress acting on soil/pile interface', 'loading rate', 'roughness of pile surface', etc. Several methods have already been proposed to estimate adfreeze bond strength during past 50 years. However, most methods have not considered the effect of normal stress for adfreeze bond strength. In this study, both freezing temperature and normal stress have been controlled as primary factors affecting adfreeze bond strength. A direct shear box was used to measure adfreeze bond strength between sand and aluminum under different temperature conditions. Based on the test results, the relation between shear strength of frozen sand and adfreeze bond strength have been investigated. The test results showed that both of shear strength and adfreeze bond strength tend to increase with decreasing frozen temperature or increasing confining pressure. The ratio of shear strength and adfreeze bond strength, expressed as $r_s$, decreased initially frozen section but increased at much lower frozen temperature and there were uniform intervals under the different normal stress conditions. A method for predicting adfreeze bond strength using $r_s$ has finally been proposed in this study.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.18 no.6
• /
• pp.237-241
• /
• 2008

Hot-press sintering of AlN ceramics were carried out with $Y_2O_3$ as sintering additive at a sintering temperature $1,750{\sim}1,850^{\circ}C$. The effect of $Y_2O_3$ addition and sintering time on sintering behavior and thermal conductivity of AlN ceramics was investigated. $Y_2O_3$ added AlN showed noticeably higher denazification rate than pure AlN. The thermal conductivity of AlN specimens was promoted by the addition of $Y_2O_3$ in spite of the formation of YAG secondary phase in AlN grain boundaries and grain boundary triple junction because $Y_2O_3$ addition could reduced the oxygen contents in AlN lattice which is primary factor of thermal conductivity. Typically, the thermal conductivity of 5 wt% $Y_2O_3$ added specimen was dramatically improved by the increase of sintering time because the elimination of YAG secondary phases from the grain boundary due to the evaporation, as well as the grain-growth of AlN grains.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.19 no.1
• /
• pp.33-38
• /
• 2009

The effect of ${Y_2}{O_3}$ as a sintering additive on thermal conductivity and microstructure of pressureless sintered AIN ceramics was investigated at sintering temperature range from 1,700 to $1,900^{\circ}C$. ${Y_2}{O_3}$ added AIN specimens showed higher densification rate than pure AIN because of the formation of the yttrium aluminates secondary phase by reaction of ${Y_2}{O_3}$ and ${Al_2}{O_3}$ of AIN surface. The thermal conductivity of AIN specimens was promoted by the addition of ${Y_2}{O_3}$ in spite of the formation of secondary phase in AIN gram boundaries and grain boundary triple junction, because ${Y_2}{O_3}$ addition could reduced the oxygen contents in AIN lattice which is primary factor of thermal conductivity. The them1al conductivity of AIN specimens was promoted by increasing sintering time because the increases of average grain size and the elimination of secondary phases from the grain boundary due to the evaporation. Particularly. the thermal conductivity of AIN specimen sintered at $1,900^{\circ}C$ for 5 hours improved over 20 %. $141\;Wm^{-1}K^{-1}$, compared with the specimen sintered at $1,900^{\circ}C$ for 1 hour.

• Korean Journal of Materials Research
• /
• v.30 no.10
• /
• pp.542-549
• /
• 2020

Effects of Sc addition on microstructure, electrical conductivity, thermal conductivity and mechanical properties of the as-cast and as-extruded Al-2Zn-1Cu-0.3Mg-xSc (x = 0, 0.25, 0.5 wt%) alloys are investigated. The average grain size of the as-cast Al-2Zn-1Cu-0.3Mg alloy is 2,334 ㎛; however, this value drops to 914 and 529 ㎛ with addition of Sc element at 0.25 wt% and 0.5 wt%, respectively. This grain refinement is due to primary Al₃Sc phase forming during solidification. The as-extruded Al-2Zn-1Cu-0.3Mg alloy has a recrystallization structure consisting of almost equiaxed grains. However, the as-extruded Sc-containing alloys consist of grains that are extremely elongated in the extrusion direction. In addition, it is found that the proportion of low-angle grain boundaries below 15 degree is dominant. This is because the addition of Sc results in the formation of coherent and nano-scale Al₃Sc phases during hot extrusion, inhibiting the process of recrystallization and improving the strength by pinning of dislocations and the formation of subgrain boundaries. The maximum values of the yield and tensile strength are 126 MPa and 215 MPa for the as-extruded Al-2Zn-1Cu-0.3Mg-0.25Sc alloy, respectively. The increase in strength is probably due to the existence of nano-scale Al₃Sc precipitates and dense Al₂Cu phases. Thermal conductivity of the as-cast Al-2Zn-1Cu-0.3Mg-xSc alloy is reduced to 204, 187 and 183 W/MK by additions of elemental Sc of 0, 0.25 and 0.5 wt%, respectively. On the other hand, the thermal conductivity of the as-extruded Al-2Zn-1Cu-0.3Mg-xSc alloy is about 200 W/Mk regardless of the content of Sc. This is because of the formation of coherent Al₃Sc phase, which decreases Sc content and causes extremely high electrical resistivity.

• Journal of the Society of Naval Architects of Korea
• /
• v.58 no.4
• /
• pp.262-270
• /
• 2021

Consumption of Liquefied Natural Gas (LNG) has increased due to environmental pollution; therefore, the need for LNG carriers can efficiently transport large quantities of LNG, is increased. In various types of LNG Cargo Containment System (CCS), Membrane-type MARK-III composed of composite materials is generally employed in the construction of an LNG carrier. Among composite materials in a Mark-III system, glass-fiber composites act as a secondary barrier to prevent the inner hull structure from leakage of LNG when the primary barrier is damaged. Nevertheless, several cases of damage to the secondary barriers have been reported and if damage occurs, LNG can flow into the inner hull structure, causing a brittle fracture. To prevent those problems, this study conducted the applicability assessment of composite material manufactured by bonding glass-fiber and aluminum with epoxy resin and increasing layer from three-ply (triplex) to five-ply (pentaplex). Tensile tests were performed in five temperature points (25, -20, -70, -120, and -170℃) considering temperature gradient in CCS. Scanning Electron Microscopy (SEM) and Coefficient of Thermal Expansion (CTE) analyses were carried out to evaluate the microstructure and thermos-mechanical properties of the pentaplex. The results showed epoxy resin and increasing layer number contributed to improving the mechanical properties over the whole temperature range.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.4 no.4
• /
• pp.349-362
• /
• 1999

To understand the role of protozoa in the early formation of microbial fouling community, the studies on the formation of microbial film, the succession of microbial fouling communities, and the grazing pressure on bacteria population in microbial film were carried out in the laboratory, Inchon outer port and Inchon inner harbour. Bacteria and heterotrophic flagellates formed primary microbial film on the aluminum surface within 6 hours and oligotrich ciliates were observed 2 cells $mm^{-2}$ on the same surface at 9 hours in Inchon inner harbour which had physically stagnant condition. The larvaes of Balanus albicostatus which were dominant meiobenthos in Inchon coastal area attached on the glass surface at the first day of experiment. Heterotrophic flagellates showed maximum abundance of 465 cells $mm^{-2}$ at the 13rd day and ciliates showed maximum abundance of 63 cells $mm^{-2}$ at the 11st day in the Inchon inner harbour. In the Inchon outer port which opens to the outer sea, the maximum abundance of protozoa occurred at early phase, but not so many. The dominant heterotrophic flagellates were Metrornonas simplex and Bodonids. Dominant ciliates were small tintinnids and oligotrich ciliate Strombidium sp., Large Strombidium (oligotrich ciliate) and sessile Acineta turberosa (suctorian ciliate) occurred after 10 days. The attached larvae of Balanus occurred as biofouling organism on the early surface and showed maximum abundance of 18 indiv. $cm^{-2}$ at 7th day. At that time, adult barnacles were observed on the surface and dead barnacles were observed after two days. Except barnacles, the larvaes of Anthozoa sp., Oysters (Crassostrea gigas) and Polychaeta were observed on the surface from 3rd day. 3 benthic copepods including Harpacticus sp., I isopod, 1 polychaeta and 1 gastropoda were observed as predators of the microbial film on the surface after 7 days when microbial film developed very well. Although the ingestion rates of protozoa on the bactctia of the rnicrobi31 film were relatively low, the average grazing rate of protozoa on bacteria was high of 0.058 $h^{-1}$. This implied that the grazing pressure of protozoa influences the mortality of bacteria populations on the microbial film. but protozoa cannot get enough energy from only bacteria on the microbial film.