• 동력기계공학회지
• /
• 제15권2호
• /
• pp.25-30
• /
• 2011

A fresh water generation system is designed for converting brackish water or seawater into fresh water. In this paper fresh water generation by distillation process that evaporates feed water and subsequently condenses vapor as evaporation product to get fresh water was studied and city water was employed as feed water. The system uses the ejector to create a vacuum, under which liquid can be evaporated at lower temperature than it at normal or atmospheric condition, hence less energy consumption. The effect of various operating conditions i.e. temperature of feed water and different orifice diameters were studied experimentally to investigate the characteristic of the system. It was found that these parameters have significant effect in the performance of fresh water generation system with low pressure evaporation.

• 설비공학논문집
• /
• 제16권3호
• /
• pp.287-292
• /
• 2004

An experimental investigation was carried out to study the performance of a bubble pump for the diffusion absorption refrigerating system. Ammonia was used as the refrigerant and the helium was charged in order to balance the pressure between the low and high pressure side. As experimental variables, the concentration of ammonia charged into system, heat input, and the pressure of helium were selected. Experimental results show that the generation rate of ammonia vapor and the circulation rate of diluted ammonia solution were increased as the heat input increases, but the ratio of the solution to vapor flow rate was decreased. The generation rate of refrigerant vapor and the circulation rate of diluted ammonia solution increased as the system pressure decreased. Finally under the condition of 25 bars, the concentration of rich ammonia solution was not affected by the generation rate of ammonia vapor and the circulation of diluted ammonia solution.

• Journal of Advanced Marine Engineering and Technology
• /
• 제32권1호
• /
• pp.175-183
• /
• 2008

In this paper, a new in-pipe inspection robot was developed for inspecting a large number of circular pipe insides of the sea plant, ships, and buildings. A new pressure generation system was devised to inspect circular pipes with different diameters and to move up and down slant or perpendicular slopes inside of the pipe. Also, a design method was analyzed to decide the capacity of driving motor for the robot if the mass and maximum velocity of the robot are identified. According to the design specification, a robot was developed and was tested to verify the performance of the pressure generation system. For tests, a control system was developed.

• 태양에너지
• /
• 제8권2호
• /
• pp.26-38
• /
• 1988

If proper design and selection of the working fluid are made the power generation system of temperature difference could achieve more efficient results than others. This paper is to analysis the production of its power generation due to several parameters. Making the power generation system, the characteristics of power output are investigated to obtain its basic data for design. This results of this experiment are as follows. 1. The most proper working fluid in the system is Freon-22 having high stability and difference between the outlet pressure, $P_E$ of evaporator and outlet pressure, $P_c$ of Condenser. 2. With the increase of temperature difference between evaporator and condenser, the output in the system increases linearly. 3. The generation efficiency is largely dependent on the type or form of propeller, nozzle and optimum design of heat exchanger.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2008년도 추계학술대회 논문집
• /
• pp.35-38
• /
• 2008

우리나라는 비교적 국토가 협소하고 산악지방이 많아 다른 나라와는 차별화 된 풍력발전시스템을 도입할 필요가 있다. 기존의 풍력발전시스템은 저풍속의 경우 발전 효율이 급격히 떨어지며 전원 품질에도 많은 문제점을 내포하고 있었다. 이를 개선하기 위하여 한국의 풍속특성에 적합한 현수형의 채택과 전원품질을 개선할 수 있는 유압모터, 동기발전기를 이용한 풍력발전시스템의 모델을 제시하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 추계학술대회 논문집
• /
• pp.51-54
• /
• 2008

This study aims to devise and analyze a power generation system combining the solid oxide fuel cell and oxy-fuel combustion technology. The fuel cell operates at an elevated pressure, a constituting a SOFC/gas turbine hybrid system. Oxygen is extracted from the high pressure cathode exit gas using ion transport membrane technology and supplied to the oxy-fuel power system. The entire system generates much more power than the fuel cell only system due to increased fuel cell voltage and power addition from oxy-fuel system. More than one third of the power comes out of the oxy-fuel system. The system efficiency is also higher than that of the fuel cell only system. Recovering most of the generated carbon dioxide is major advantage of the system.

• 에너지공학
• /
• 제20권3호
• /
• pp.178-184
• /
• 2011

압축공기저장(CAES) 발전은 가스터빈에 필요한 압축공기를 야간이나 비첨두 시간에 저렴한 전기로 미리 압축해서 저장하였다가 주간에 활용하는 것으로 전력 저장과 발전의 하이브리드 기술이라고 할 수 있다. 그러나 기존 압축공기저장 발전의 경우 심야에 압축공기를 일정부피의 압축공기 저장조에 충전하게 되면 저장조내의 압력은 점점 증가하게 되고, 반대로 주간에 발전을 위해 압축공기를 방출하게 되면 저장조내의 압력은 감소하게 된다. 이와 같이 운전 압력비 조건이 넓은 범위로 변화하여 설계 압력비에서 벗어나게 되는 것은 압축 및 팽창효율이 크게 감소하게 되는 원인이 된다. 본 논문에서는 이러한 기존의 변압식 압축공기저장 발전 방식의 문제점을 해결하기 위해 새로운 방식의 정압식 압축공기저장 발전 방식을 제시하고 있으며, 엑서지 개념을 포함한 에너지 분석을 통해 에너지 밀도 증가와 효율 향상 효과를 예측하였다. 새로운 방식의 정압식 압축공기 저장 발전 방식은 정압식 압축공기 저장 발전과 공압식 양수발전의 하이브리드 개념으로 기존 변압식 압축공기저장 발전 방식에 비해 정압 운전에 의한 효율향상과 에너지 밀도 증가로 압축공기 저장조의 크기를 50%이상 줄일 수 있는 장점을 가지고 있다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제33권5호
• /
• pp.662-671
• /
• 2009

In this paper, a robot was developed for in-pipe cleaning and inspecting a large number of circular in-pipes of sea plants, ships, and buildings. A pressure generation mechanism was devised to inspect circular in-pipes with different diameters and to move up and down slant or perpendicular slopes in-pipes. For inspection of the dark inner side of the pipe, a light system using LED which dissipats small electricity was developed. Also, a design method was analyzed to decide the capacity of driving motor for the robot when the mass and maximum velocity of the robot are identified. The robot developed based on the design specification, was tested to verify the performance of the pressure generation mechanism. In addition, a control system was developed for the test.

• 한국기계기술학회지
• /
• 제13권4호
• /
• pp.85-91
• /
• 2011

Experimental analysis has been carried out to investigate thermal characteristics of hydraulic system in special vehicles. Hydraulic system performance is largely influenced by oil temperature, and there are considerable performance decline and malfunctions in the system for high temperature conditions caused by heavy load and continuous operation. Transient oil temperature and pressure variation are analyzed and heat generation rates in the several main system parts are compared for various flow rates. With the start of system operation oil temperature gradually increases, and viscosity deceases by about 70% as temperature increases from $20^{\circ}C$ to $80^{\circ}C$. Operation pressure in the hydraulic system decreases with oil temperature, and its variation rate becomes less steep as oil temperature increases. Heat generation rate in hydraulic pump also depends on the oil temperature, and it reaches maximum near $50^{\circ}C$. These results in this study can be applied to optimal design of efficient hydraulic system in special vehicles.

• Korean Chemical Engineering Research
• /
• 제57권1호
• /
• pp.28-41
• /
• 2019

본 연구는 소듐냉각고속로 원형로 소듐-물 반응 압력완화계통의 성능 해석을 목적으로 한다. 증기발생기의 전열관 파단에 의한 대규모 물 누출 사고 발생 시, 증기발생기 전열관 내측의 물을 급수덤프탱크로 배출하고 전열관 외측의 소듐 및 반응생성물을 소듐덤프탱크로 배출 할 때 유체의 거동을 해석하여 계통 설계요건의 적절성을 평가하였다. 증기발생기 쉘 측의 액체와 중간열전달계통 내 소듐이 모두 배출되는데 소요되는 시간은 약 50초이고, 증기발생기 전열관 측의 급수가 모두 배출되는데 소요되는 시간은 약 2.5초로 계산되었다. 증기발생기와 중간열전달계통 내 유체가 덤프탱크로 배출되는 동안 전열관 측의 압력은 쉘 측의 압력보다 높게 유지되어 쉘 측의 소듐이 전열관 측으로 역류하는 현상은 없는 것으로 해석되었다. 본 연구의 결과는 SFR 원형로 소듐-물반응압력완화계통의 성능 평가에 대한 기초자료로 활용할 예정이다.