• 한국생활환경학회지
• /
• 제24권4호
• /
• pp.533-540
• /
• 2017

This study analyzes the stretchability and clothing pressure of fabrics made from stretchy knit materials, and uses the baseline data to develop various functional clothing made from stretchy knit fabrics. To observe the changes in the stretchability and clothing pressure, we observed the compatibility of the two materials (tricot and power-net), presence of flat seam, fabric layering, and flat seam direction as key variables. A standard test method for stretch properties (ASTM D2594) was used for measuring the stretchability of the material. Clothing pressure measurements were analyzed in terms of the mean and standard deviation values, and the correlation of the stretchability. In the case of tricot, the presence of flat seam increased the stretchability of the fabric regardless of the fabric layering. However, when tricot and the less stretchable power-net were combined, the presence of flat seam did not increase the stretchability. Flat seam did not interfere with or limit the stretchability of the fabric, but they did increase the clothing pressure at the seam. The stretchability had a negative correlation with the clothing pressure except along the flat seam.

• Journal of Advanced Marine Engineering and Technology
• /
• 제25권1호
• /
• pp.115-123
• /
• 2001

This study describes the combustion characteristics under various condition of air excess ratio and ignition timing in a 2-valve gasoline optically accessible engine with swirl control valve(SCV). It adapted three different types of SCA(open ration 72.5%, 78%, 89%) to strengthen a swirl flow. Pressure data were acquired using pressure sensor to investigate the effect of swirl flow on combustion, and from these pressure data, IMEP(indicated mean effective pressure) and MFB(mass fraction burnt)were calculated to explain burn rate and flame speed. From acquired flame images, inspected the flame propagation direction, flame area, and flame centroid, Flame propagation direction was shown different tendency between with/without SCV, and flame area with SCV was faster and larger than that of conventional engine. Finally, the representative flame image at each crank angle were acquired by PDF method to verify flame growth process. It is found that strengthened swirl flow is more beneficial for faster and stable combustion.

• 한국가구학회지
• /
• 제18권2호
• /
• pp.111-119
• /
• 2007

An experiment was conducted to know the safranine impregnation distance from surface to inward using 6 different hardwood species. During impregnation, 3 parameters were applied-vacuum, pressure and soaking time. Only vacuum treatment did not increase the permeability of wood. Vacuum followed by pressure increased the penetration depth of safranine in radial, tangential and longitudinal direction. Longitudinal penetration was found easy to impregnate. Comparing with radial and tangential direction, radial penetration was found easy. There was a striking difference among sapwood and heartwood permeability. Safranine input depth was found highest in diffused porous wood rather than in ring porous wood. At increased vacuum and pressure, safranine penetration was found easy.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.462-466
• /
• 1997

Proportional directional control valves (PDCVl adjust the amount of flow as well as flow direction in response to an electrical signal. This valves includes direct operated valves with or without spool position feedback. This paper investigates if it is possible to control pressure of fluids by means of the PDCV. A pressure signal is feed back to the Proportional-Integral (PI) controller, which is based upon a personal computer (PC). The PI control algorithm is implemented in a graphical programming language of LabVIEW. The results of experiments show the PDCV can be used a multi function valve of pressure control as well as direction control.

• Wind and Structures
• /
• 제21권4호
• /
• pp.383-405
• /
• 2015

This study investigated aerodynamic characteristics of an inclined square prism experimentally. Pressure measurements were performed on a static square prism with a series of inclinations including forward inclinations (inclined to the upwind direction) and backward inclinations (inclined to the downwind direction). The prism with a vertical attitude was also tested for comparisons. Based on the pressure data, influences of the inclinations on aerodynamic characteristics (e.g., force coefficients, pressure distributions on the surfaces, and vortex shedding features) of the square prism were evaluated in detail. The results show that the inclinations have significant effects on these aerodynamic characteristics. Furthermore, the influences of the forward and backward inclinations are quite different.

• 한국의학물리학회지:의학물리
• /
• 제22권2호
• /
• pp.72-78
• /
• 2011

본 연구의 목적은 토모테라피(Hi-ArtII, TomoTherapy, USA) 치료 시 Bodyfix system (Medical Intelligence, Ele-kta, Schwabmuchen, Germany)에서 진공압박(Vacuum compression)에 따라 환자 위치잡이오차(Patient's setup-errors)를 평가하고자 하였다. Bodyfix system와 진공압박을 적용한 토모테라피를 이용하여 치료를 시행한 흉복부 환자 21명을 선정하였으며, 모든 환자는 치료 전 촬영된 총 477개의 메가볼테이지 전산화단층촬영(Mega-voltage computed tomography, MVCT)영상을 얻었다. 이를 통하여 확인된 좌우방향(Medial-Lateral direction, ML), 앞뒤방향(Anterior-Posterior direction, AP), 상하방향(Superior-Inferior direction, SI)과 SI중심축 회전각(Rotational angle of SI axis direction, Roll)에 대한 오차를 기록하고, 분석하였다. 세 방향 및 Roll에 대한 상관관계와 진공압박 정도가 다르게 적용된 다섯 그룹에 대하여 setup-errors를 분석하기 위해 각각 Pearson's product-moment coefficient와 One-way ANOVA를 이용하여 통계적으로 분석하였다(p<0.05). 분석결과 Systematic errors의 평균은 AP에서 6.00 mm, 표준편차는 SI에서 5.95 mm로 큰 오차를 보였다. Random errors의 평균은 SI방향에서 4.72 mm로 큰 오차가 발생하였다. 관계분석에서는 상관계수가 ML-Roll과 AP-Vector는 0.485, 0.244이고, SI-Vector에서 관계가 제일 높았다(0.637). 또한, 진공압박 정도가 다르게 적용된 다섯 그룹(Pressure range: 30~70 mbar) 사이의 setup errors를 분석한 결과 ML, SI방향과 Roll에서 모두 p=0.00 (p<0.05)로써 유의한 차이를 보였으며, SI방향에서 진공압박에 따른 오차 평균은 40 mbar과 70 mbar그룹에서 4.78 mm, -0.74 mm였다. 본 연구에서는 진공압박과 setup-errors의 평가를 통계적으로 분석하였으며, 압박 정도에 따라 SI방향에서 setup-errors의 차이를 확인하였다. 최종적으로 setup-errors와 내부장기의 움직임을 고려하자면 Bodyfix system을 이용한 진공압박을 적용시 최소 50 mbar 이상을 사용해야 할 것이다. 본 연구결과를 토대로 진공압박의 정확성과 내부장기 및 종양의 움직임을 정량적으로 분석할 필요가 있다고 판단된다.

• 한국건축시공학회지
• /
• 제5권3호
• /
• pp.131-138
• /
• 2005

The study is focused on the settling the developing direction of korean gas pressure welding machine which can be applied in korean construction sites with moderate and high performance. Gas pressure welding is more economical and has good performances than other steel bar jointing methods, as arc welding and mechanical joint etc. Therefore in Japan, the gas pressure welding, which has less loss of steel bars and low performance of joints, when connecting the D29 and thicker steel bars, Is one of the typical connection of steel reinforcement. But in Korea, the gas pressure welding method is not widely used caused by the shortage of skilled workers, and this situation in Korea can not be solved in short period. The training of the skilled workers takes long period(around $6\~10$ years), and there is no certification system for gas pressure welding. So to activate the gas pressure welding in Korea, the development of the automatic gas pressure welding machine is necessary, which gives regular performance of the steel bar joints and can be operated by not sufficient skilled workers. The automatic gas pressure welding machine was developed in Japan, but this machine has many problems when applied in korean construction sites. Therefore, it is necessary to develop a korean automatic gas pressure welding machine to overcome this problems. To develop korean automatic gas pressure welding machine, the problems, which shows when applied in korean construction sites, need to be investigated. According to the investigation, counterproposals are presented for the pragmatical development of the korean automatic gas pressure welding machine.

• International Journal of Fluid Machinery and Systems
• /
• 제7권2호
• /
• pp.42-53
• /
• 2014

Phase resonance in Francis type hydraulic turbine is studied. The phase resonance is a phenomenon that the pressure fluctuation in the penstock of hydraulic turbine installation can become very large when the pressure waves from each guide vane caused by the interaction with the runner vane reach the penstock with the same phase. Experimental and numerical studies have been carried out using a centrifugal fan. In the present study, comparisons between the pump mode and the turbine mode operations are made. The experimental and numerical results show that the rotational direction of the rotor does not affect characteristics of the pressure fluctuation but the propagation direction of the rotorstator interaction mode plays an important role. Flow rate fluctuations through the stator are examined numerically. It has been found that the blade passing flow rate fluctuation component can be evaluated by the difference of the fluctuating pressure at the inlet and the outlet of the stator. The amplitude of the blade passage component of the pressure fluctuation is greater at the stator inlet than the one at the stator outlet. The rotor-stator interaction mode component is almost identical at the inlet and the outlet of the stator. It was demonstrated that the pressure fluctuation in the volute and connecting pipe normalized by the flow rate fluctuation becomes the same for pump and turbine mode operations, and depends on the rotational direction on the interaction mode.

• Geomechanics and Engineering
• /
• 제17권6호
• /
• pp.535-541
• /
• 2019

Combining the radial well drilling and hydraulic fracturing technique, the production capacity of the reservoirs with low-permeability can be improved effectively. Due to the existence of radial holes, the stress around the well is redistributed, and the initiation and propagation of hydraulic fractures are different with those in traditional hydraulic fracturing. Therefore, it is necessary to study the influences of radial horizontal wells on hydraulic fracturing. The laboratory experiment was conducted to simulate the hydraulic fracturing on the physical model with radial holes. The experimental results showed that, compared with the borehole without radial holes, the sample with radial hole in the direction of maximum horizontal stress was fractured with significantly lower pressure. As the angle between direction of the horizontal hole and the maximum horizontal stress increased, the breakdown pressure grew. While when the radial hole was drilled towards the direction of the minimum horizontal stress, the breakdown pressure increased to that needed in the borehole without radial holes. When the angle between the radial hole and the maximum horizontal stress increase, the pressure required to propagate the fractures grew apparently, and the fracture become complex. Meanwhile, the deeper the radial hole drilled, the less the pressure was needed for fracturing.

• 한국염색가공학회지
• /
• 제8권6호
• /
• pp.1-8
• /
• 1996

The crystal structures of Nylon 6 films with the changes of pressure, temperature, and the processing time were examined. The accompanying physical property changes such as the weight fraction, the crystallinity, the crystal size, the initial modulus, and the thermal properties, gives the following results. When the sample is processed at 16$0^{\circ}C$, the weight fraction is not changed significantly with varying pressure. However, at 18$0^{\circ}C$ a significant change of the weight fraction was found with increasing pressure above 5 ton/in$^{2}$ so as to increase the crysallinity. As long as the ct transition is concerned we found that it begins from 14$0^{\circ}C$ and is completed at 18$0^{\circ}C$ and 9 ton/$in^{2}$ of pressure with the processing time of 120 min. The increase of the initial modulus is believed to be due to the increase of the number of the tie chains and the tension resulting from the change of the crystal size in the direction perpendicular to the direction of the applied pressure. The meltiong point change is due to the pressurized crystallization was not observed.