• 한국안전학회지
• /
• 제23권5호
• /
• pp.22-29
• /
• 2008

This paper provides the evaluation method for the pressure vessel with internal wall-thinning defect, which is based on ASME design criteria. Pressure vessel has wall-thinning partially and patch reinforcement has been attached for reliable operating. However, present partial wall thinning could be through wall thinning at the next inspection time with present corrosion progress speed. Therefore safety margin was calculated for various conditions from present wall-thinning condition to additive patch reinforced condition via two-dimensional and three-dimensional, geometrically linear FE analyses using elastic materials.

• 한국가스학회지
• /
• 제7권3호
• /
• pp.51-57
• /
• 2003

본 논문에서는 압력용기의 밀봉성과 밀접한 관계를 맺고 있는 O-링 그루브 형상의 온도분포와 변형거동 특성에 대한 연구를 수행하고자 한다. 압력용기에 작용하는 온도는 히터에 의해 가열되고, 압력은 가스 압축기에 의해 가압된다. 결국, 압력용기는 제한된 작업기간동 안 높은 압력과 높은 온도를 유지해야 한다 이러한 작동조건에서 압력용기의 가스는 구형 그루브에 설치된 두 개의 O-링에 의해 대기중으로 누출되지 말아야 한다. 유한요소해석 결과에 의하면, 압력용기의 밀봉성을 확보하기 위해서는 메탈 시일 소재의 열적, 기계적 특성이 대단히 우수해야 한다는 사실을 지적하고 있다 즉, 메탈 시일 소재는 높은 열전도 계수와 낮은 기계적 강도를 유지해야 밀봉성을 유지하는데 유리하다. 이러한 소재는 O-링을 설치하는 구형 그루브의 밀봉간극이나 그루브의 폭을 줄여줄 수 있기 때문에 압력용기의 밀봉특성을 향상시키게 된다.

• 한국해양공학회지
• /
• 제13권4호통권35호
• /
• pp.82-97
• /
• 1999

A deep sea vehicle must be designed to ensure its safety under ultra-high pressure circumstances. If a pressure housing of a deepsea vehicle is collapsed by ultra-high pressure, the deepsea vehicle may be lost. The objective of this paper is to introduce a design collapse pressure for the deep sea pressure vessel which is composed of one cylinder and two hemispheres. Especially the collapse pressure of hemispherical shell with a hole at top is analyzed by a variational approach (weighted residual method). And for the purpose of design, the salty factor of collapse pressure is presented which is analyzed by interpolation method.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2009년도 추계학술발표대회 논문집
• /
• pp.409-414
• /
• 2009

Since cryogens are stored at very low temperatures, the cryogenic storage systems are quite sensitive to heat leaks. Even though the vessel operated under sealed condition with vacuum insulation and reflective coatings are used, the heat leakage into the vessel is still unavoidable. Therefore, this paper concerns with numerical study of self-pressurization used to analysis the optimum design with the variation volume fraction, effect of heat flux and storage pressure of liquid nitrogen. The result shows that as the volume fraction increases, the pressure rise reduces and the relatively at atmosphere pressure is better than the higher one. In addition, higher heat flux leads the pressure rise increases faster than low one. The additional of heat pipe system to reduce the pressure rise rate also has been done. By this comparison, the optimum design for storage umbilical cord blood can be selected.

• 한국해양공학회지
• /
• 제30권3호
• /
• pp.201-207
• /
• 2016

In this paper, an aluminum pressure vessel (cylinder) for a 200 m water depth is designed and analyzed. Because of their lack of usage in the deep sea, only a few papers about pressure vessels subjected to external pressures have previously been published. Moreover, the high level of imported external-pressure-vessel products limits the academic pursuit. Yet, research on internal pressure vessels is widely available because of their broad usage at onshore. This paper presents the process of basic designing and modelling of pressure vessels using the design rules of American Standard of Mechanical Engineering (ASME) Section VIII Division 1. To promote understanding, finite element analysis (FEA) result of an existing sample cylinder which was not designed by ASME code is compared with the design obtained in this paper. Several methodologies are used for the finite element analysis, including rectangular, cylindrical, and axisymmetric coordinate, to attain an accurate stress result. Same dimensions except the thickness of the cylinder and loading condition of 0.200 MPa was given for the current study. Finally, a rigorous design procedure is added for the bolt and boundary conditions of the cylindrical body and its ends. The obtained stress level satisfies the allowable design stress value specified in the ASME code.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.545-550
• /
• 2004

KSTAR cryostat is a 8.8 m diameter vacuum vessel that provides the necessary thermal barrier between the ambient temperature test cell and the supercritical helium cooled superconducting magnet providing the base pressure of 1 ${\times}$ $10^{-3}Pa$. The cryostat is a single walled vessel consisting of central cylindrical section and two end closures, a flat base structure with external reinforcements and a dome-shaped lid structure. The base structure has 8 equally spaced support legs anchored on the concrete base. The cryostat vessel design was executed to satisfy the performance and operation requirements. The major loads considered in the structural analysis were vacuum pressure, dead weight, electromagnetic load driven by plasma disruption, and seismic load. Based on the fabrication and inspection procedures for the vessel, cryostat vessel was fabricated and inspected. It was confirmed that the inspection results were acceptable.

• 드라이브 ㆍ 컨트롤
• /
• 제14권3호
• /
• pp.32-39
• /
• 2017

In this study, a mathematical model of the pneumatic part in a gas blow-down system is proposed. The mathematical model consists of four major parts: pressure vessel, reservoir, pressure regulator and pipe-line. To ensure accuracy in long-time simulations, heat transfer between gas and pressure vessel is considered. The model is validated by comparing simulation results with experimental data. Experiments are conducted on the ground, where free convection can be assumed. Simulation results indicate the proposed model can accurately describe behavior of a gas blow-down system. Therefore, it may be used for design and analysis of similar systems with a slight modification.

• 한국정밀공학회지
• /
• 제20권1호
• /
• pp.205-213
• /
• 2003

The fiber reinforced composite material is widely used in the multi-industrial field where the weight reduction of the infrastructure is demanded because of their high specific modulus and specific strength. It has two main merits which are to cut down energy by reducing weight and to prevent explosive damage preceding to the sudden bursting which is generated by the pressure leakage condition. Therefore, Pressure vessels using this composite material in comparison with conventional metal vessels can be applied in the field such as defense industry, aerospace industry and rocket motor case where lightweight and the high pressure are demanded. In this paper, for nonlinear finite element analysis of E-glass/epoxy filament winding composite pressure vessel receiving an internal pressure, the standard interpretation model is developed by using the ANSYS, general commercial software, which is verified as the accuracy and useful characteristic of the solution based on Auto LISP and ANSYS APDL. Both the preprocessor for doing exclusive analysis of filament winding composite pressure vessel and postprocessor that simplifies result of analysis have been developed to help the design engineers.

• 한국정밀공학회지
• /
• 제20권8호
• /
• pp.21-29
• /
• 2003

This paper describes a research work on the development of computer-aided design system for deep drawing & ironing of a high pressure vessel. An approach to the system is based on the knowledge-based rules. Knowledge for the system is formulated from plasticity theories, handbook, experimental results and empirical knowledge of field experts. An attempt is made to link programs incorporating a number of expert design rules with the process variables obtained by commercial FEM software, DEFORM and ANSYS, to form a useful package. It is composed of five main modules, which are calculation of product thickness, input, production feasibility check, process planning, and autofrettage process modules and two submodules, which are folding check and process variable verification submodules. Programs for the system have been written in AutoLISP on the AutoCAD 2000 using personal computer. The developed system makes it possible to design and manufacture large high pressure vessel requiring D.D.I. process more efficiently.

• Composites Research
• /
• 제19권3호
• /
• pp.7-14
• /
• 2006

본 논문에서는 내압 하중을 받는 복합재 압력 용기의 신뢰도를 구하기 위해 확률적 강도 해석이 수행되었다. 이때 확률적 강도 해석은 점진적 파손 모델과 몬테카를로 시뮬레이션으로 구성된 확률 연속 파손 모델과 상용 유한 요소 해석 코드인 ABAQUS가 연계한 형태로서 복잡한 형상 및 경계 조건을 갖는 복합재 구조물의 확률적 파손 해석을 수행하게 된다. 설계확률 변수로서 복합재 층의 각 방향 별 강도가 고려되었다. 최종적으로, 확률 강도 해석을 통해 복합재 압력 용기의 파열 압력 분산 현상이 설명되었고, 복합재 압력 용기의 각 부위별 신뢰도 값이 제시되었다. 양산 중인 복합재 구조물인 경우, 재료 및 제작 공정의 불확실성이 구조물 성능에 미치는 영향이 더욱 커지게 되어 확률 강도 해석을 이용한 구조 설계가 필수적이다.