• 설비공학논문집
• /
• 제22권1호
• /
• pp.13-20
• /
• 2010

Airborne particulate matters have two modes of size distributions of coarse mode and fine mode. The coarse mode which is formed by break down mechanism of large particles has a peak around the $100\;{\mu}m$, and the fine mode formed by condensation and build up mechanism of evaporated vapors has a peak at several ${\mu}m$. The coarse mode particles can be removed easily by conventional collecting equipments such as a cyclone, an electrostatic precipitator, and a filter, however the fine mode particles can not be collected easily. Usually the fine mode particles are generated in the high temperature conditions especially through boilers and incinerators, so the high efficient and temperature filter is essential for the filtration. In this study, a nano ceramic filter for the removal of fine particles in the high temperature is developed and tested for several characteristics. The nano ceramic filter has double layer of micro and nano structure and the pressure drop and the filtration efficiency for $0.31\;{\mu}m$ at 3 cm/s are 15.45 mmAq, and 96.75%, respectively. The thermal conductivity is $0.038\;W/m{\cdot}K$, and the coefficient of water vapor permeability is $3.63\;g/m^2{\cdot}h{\cdot}mmHg$. It is considered that the sensible heat exchange rate is very poor because the low thermal conductivity but it has high potential to exchange latent heat.

• Journal of Welding and Joining
• /
• 제28권1호
• /
• pp.66-71
• /
• 2010

With large specific strength and outstanding corrosion resistance and erosion resistance in sea water, titanium and titanium alloy are widely used in heat exchanger production. In particular, pure titanium demonstrates outstanding molding performance and may be considered optimal for production of heat exchanger. Since titanium is very vulnerable to oxidation and embrittlement during welding, processes with less heat input are widely used, and laser welding is widely applied by considering production performance and shield etc in atmosphere. So far, 1st report and 2nd report compared and analyzed embrittlement degrees by bead colors of weldment through oxygen and nitrogen quantitative analysis and hardness measurement, and evaluated welding performance and mechanical properties of butt welding. This study evaluated field applicability of lap welding to heat exchange plate of LPG re-liquefaction device for ships through tensile stress test, hardness test and internal pressure test etc after deducing optimal weding condition and applying to actual heat exchange plate. In bead overlap area, the experiment produced sound welds with no porosity or defect by increasing and decreasing laser power, and tensile-shear test results indicated virtually the same tension and yield strength as base metal. As a result of measuring hardness at lateral cross section and bead overlap zone of actual heat exchanger welds, hardness difference within 20Hv was produced at base metal, HAZ and weldment, and as a result of pneumatic and hydraulic pressure test, no leakage occurred.

• 한국응용과학기술학회지
• /
• 제25권1호
• /
• pp.58-64
• /
• 2008

Pretreatment of eliminating FFA is needed to make biodiesel from animal fat recovered from leather wastes because its acid value is high. This study was carried out to investigate the influence of 4 different pretreatment methods, which are heterogeneous catalyst method, ion exchange resin method, low pressure.high temperature method, and alkali method on the eliminating FFA and fatty acid composition. The results showed that the rate of eliminating FFA increased in the order of alkali method > catalyst method > low pressure high temperature method > ion exchange method. In the case of pretreatment of alkali method using NaOH, the rate of eliminating FFA appeared more than 86% regardless of acid value. Therefore, it was considered that alkali method using NaOH was the most effective in the view of economical and productive aspects, taking it into account that the acid value of animal fat recovered from fleshing scrap generated during leather making processes was 7 to 8.

• 폴리머
• /
• 제37권4호
• /
• pp.533-538
• /
• 2013

염화나트륨은 우리 몸의 체액에 존재하며, 혈액 속에 약 0.9 wt%의 농도로 존재하여 삼투압을 유지하는 중요한 역할을 하고 있다. 그러나 사람들이 섭취하는 소금의 양은 증가하는 추세이며, 과량 섭취로 인해 고혈압 등의 원인이 되기도 한다. 본 연구에서는 생체적합성 이온성 고분자들의 특정 반대이온을 칼슘과 칼륨으로 치환시켜 나트륨 이온과의 이온교환을 통해 고분자에 나트륨이 흡착되어 대변으로 배출시킬 수 있는지를 in vitro 실험과 in vivo 실험을 통해 연구하였다. 조사된 고분자들 중 칼슘과 칼륨의 폴리스티렌설폰산, 칼슘 치환된 카라기난과 타마린드가 우수한 나트륨 치환 능력을 보유하고 있음을 확인하였고, 체온과 인공위액 및 인공장액의 조건에서도 나트륨 치환능을 유지하는 것을 확인하였다. 이러한 고분자들의 난용성 특징을 통해 구강 내에서는 맛의 변화를 주지 않으면서 나트륨을 흡착해 배설하는 메카니즘을 나트륨 과다 섭취에 따른 문제 해결을 위해 활용할 수 있을 것으로 사료된다.

• 대한기계학회논문집B
• /
• 제36권10호
• /
• pp.989-999
• /
• 2012

이젝터는 고압의 유체를 구동관로에서 분출시켜, 그 주변의 저압기체와 운동량 교환을 통하여 저압의 유체를 보다 높은 압력까지 상승시켜 흡인되는 유체를 이송하는 장치이다. 증기-증기 이젝터는 흡입, 혼합 및 탈수에 널리 사용되고 있다. 그리고 이젝터는 기계적인 작동이 없으므로, 고장이 거의 없다. 또한 이젝터는 유체 관련 시스템의 크기에 관계없이 유체와 관련된 다양한 장소에 용이하게 설치할 수 있어, 정비의 필요성이 거의 없고 비용도 합리적이다. 따라서 본 연구는 단순 압축 또는 진공 설비를 위한 펌프 혹은 기계장치 대안으로 사용되는 이젝터 전체에 적용할 수 있는 기초 자료 제공을 목표로 하였다. 이 목표를 위해 실험만으로 획득할 수 없는 자료를 전산유체역학을 적용하여 분석함으로써 이젝터의 유체역학적 특성에 있어 최적의 설계조건을 제시하였다.

• 한국수소및신에너지학회논문집
• /
• 제20권6호
• /
• pp.499-504
• /
• 2009

The effect of gas diffusion layer (GDL) compression caused by different stack clamping pressures on fuel cell performance was experimentally studied in a miniature 5-cell proton exchange membrane fuel cell (PEMFC) stack. Three stacks with different GDL compressions, 15%, 35% and 50%, were prepared using SGL 10BC carbon fiber felt GDL and Gore 57 series MEA. The PEMFC stack performance and the stack stability were enhanced with increasing stack clamping pressure resulting in the best performance and stability for the stack with higher GDL compressions up to 50%. The excellent performance of the stack with high GDL compression was mainly due to the reduced contact resistance between GDL and bipolar plate in the stack, while reduced gas permeability of the excessively compressed GDL in the stack hardly affected the stack performance. The high stack clamping pressure also resulted in excessive GDL compression under the rib areas of bipolar plate and large GDL intrusion into the channels of the plate, which reduced the by-pass flow in the channels and increase gas pressure drop in the stack. It seems that these phenomena in the highly compressed stack enhance the water management in the stack and lead to the high stack stability.

• 한국자동차공학회논문집
• /
• 제17권2호
• /
• pp.159-164
• /
• 2009

Cooled EGR system is an effective method for the reduction of $NO_x$ emission and PM emission from a diesel engine. Proper choice of wavy cooling fins and gas tubes is a key factor of cooled EGR system. As a part of solutions for energy crisis and environmental problems, hybrid vehicles mounted with diesel engines are under development globally. This study investigates the cooled EGR systems for hybrid diesel engine with the specifications of both optimized wavy cooling fins and improved shape of structure to verify the heat exchange efficiency, outlet temperature and gas pressure drop of cooler by means of numerical analyses and rig performance tests. The output of this study will be applied to a 2.0L hybrid diesel engine which is being developed for domestic and overseas market.

• 한국자동차공학회논문집
• /
• 제19권1호
• /
• pp.101-108
• /
• 2011

Understanding the exhaust gas recirculation (EGR) cooler fouling in diesel engine is important factor in the durability characteristic of a EGR system. We develope a test rig and PM feeder using carbon black to examine the effect of fouling on EGR cooler devices those were consisted of flat and shell & tube type. The EGR cooler fouling process is a complex interaction involving heat exchanger shape, boundary condition, constitutes, chemistry and operating mode. As the soot deposited to EGR cooler, these formed a thin deposit layer that was less heat exchange than the fresh status of tube enclosing the exhaust gas, resulting in lower heat exchange effectiveness in both type coolers. But these deposits caused different results in pressure drop, it is increased in flat type, but decreased in Shell & tube type of EGR cooler. A cause was estimated from a change of the flow structure and a decrease of contact area as the EGR cooler fouling.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 추계학술대회
• /
• pp.368-371
• /
• 2006

[ $La_{0.8}Sr_{0.2}Co_{1-x}Mn_xO_3$ ] cathode as a high performance cathode on YSZ electrolyte was studied by analyzing impedance spectra. It was shown that cathode property of $La_{0.8}Sr_{0.2}Co_{1-x}Mn_xO_3$ is bet ter than that of$La_{0.8}Sr_{0.2}CoO_3$. At $700^{\circ}C$ in air environment, $La_{0.8}Sr_{0.2}Co_{0.4}Mn_{0.6}O_3$ cathode on CGO- layered YSZ electrolyte showed very low area specific resistance of $0.14{\Omega}cm^2$, which is low enough for intermediate-temperature sol id oxide fuel cells. This is because material properties of ionic conductivity and thermal expansion compatibility with electrolyte were optimized. Judging from activation energy and oxygen part i al pressure dependance of cathode property, it was noted that oxygen surface exchange kinetics is dominantly influential on cathode property in higher temperature region than $700^{\circ}C$ and oxygen self-diffusion in cathode material is more influential in lower temperature region.

• 지능정보연구
• /
• 제10권2호
• /
• pp.189-209
• /
• 2004

수요사슬에서 기업간 협업은 통합 (Integration), 협업(Exchange), 그리고 동기화(Syncronize)라는 3 단계의 계층구조를 갖으며, 단계가 높을수록 협업의 지능성은 강하다. 이 논문은 국내의 제조업과 서비스업을 중심으로 지능적인 수요사슬 통합전략(공급통합, 수요통합, 수요사슬통합)을 수행하는데 영향을 주는 동인들을 발견한다. 여기 동인에는 효율적 동인과 시대적 동인으로 구분하여 각 통합전략에 어떻게 영향을 미치는 지를 조사하여, 그 특징을 파악하고 문제점을 제시한다. 인터넷 강국인 국내기업의 통합전략과 동인에 대한 면밀한 분석을 통해 기업에게 가장 이상적인 통합전략이 무엇인지를 제시한다. 결론에서는 고객과 통합을 추진하는 통합전략을 선택한 기업은 웹통합을 하는 가장 큰 이유는 경영성과를 높이기 위해 추진하는 것으로 나타났으며, 공급자와 통합을 하는 전략을 선택한 기업은 외부환경의 압력에 의해서 어쩔 수 없이 추진하는 것으로 해석된다.