• Journal of the Korean Wood Science and Technology
• /
• v.21 no.2
• /
• pp.39-48
• /
• 1993

End-matched disks of 7.7cm thickness were part-time dried in vacuum press dryer to investigate the drying characteristics by using drying schedules and end treatments. The ginkgo disks could be dried faster with severer end checks and ring failures by C schedule than by S schedule. There were no significant differences in drying rates and amounts of end checks, ring failures and V-shaped checks occurred between ginkgo disks end-taped with Korean traditional paper (KTP) and those untreated. The drying time of walnut disks was slightly reduced by end-taping with KTP. And the length of end checks and V-shaped checks and the frequency of defected disk were decreased more effectively than those untreated. The tangential strains and tangential drying stresses near bark sides of ginkgo and walnut disk untreated were developed in the early stage of drying and incresed slightly curvi-linearly above fiber saturation point (fsp) and more curvi-linearly below fsp. The influence of end-taping with KTP on the drying rate for impermeable walnut disk was stronger than that for permeable ginkgo disk.

• Journal of the Korean Wood Science and Technology
• /
• v.15 no.2
• /
• pp.67-78
• /
• 1987

This study was designed to investigate the effect of board thickness and ring angle on the characteristics including internal check. ring failure, surface check, end check, collapse, thickness shrinkage and width shrinkage of press-drying. The exprimental materials of 6mm-. 9mm- and 12mm-thick board were taken from heartwood and sapwood of oak (Quercus acutissima Carr.) respectively. And boards were numbered according to position in the log(No. 1 to No. 4 for heartwood :md No. 9 for sapwood). Press-drying was at $145^{\circ}C$ platen temperature and 3.5kg/$Cm^2$ platen pressure. The results of this study were summarized as follows. 1. Drying rates for sapwood materials were greater than those for heartwood materials. And drying rates for thinner materials were greater than those for thicker materials. 2. The thinner boards were. the severer surface checking developed in the heartwood materials, and surface checking for heartwood materials had no tendency in board position for the same thickness. Sapwood materials were completely free from surface checking. 3. End checking for heartwood materials had no tendency in board position. The greater deviation of ring angle from perfectly edge-grained was, the severer and checking developed in the sapwood materials. But end checking did not occur in 6mm-thick sapwood materials. 4. The greater deviation of ring angle from perfectly edge-grained was, the severer end checking developed for heartwood and sapwood materials. As board thickness increased, maternal checking developed more severely for heartwood and sapweed materials. 5. For heartwood materials, ring failure, reduced with increasing deviation of ring angle from perfectly edge-grained except 12mm-thick material and showed no significant difference attributable to board thickness. Sapwood materials were completely free from ring failure. 6. For heartwood and sapwood materials, collapse was slight and showed no significant differences attributable to both board thickness and board position. 7. As deviation of ring angle from perfectly edge-grained increased, shrinkage of board thickness decreased for heartwood and sapwood materials. 8. Shrinkage of board width showed no significant differences attributable to both board thickness and board position for heartwood and sapweed materials.

• Computers and Concrete
• /
• v.14 no.6
• /
• pp.635-656
• /
• 2014

A rational estimation of moisture distribution in structural concrete is vital for predicting the possible extent and rate of progression of impending degradation processes. The paper proposes a numerical scheme for analysing the evolution of moisture distribution in concrete subjected to wetting-drying exposure caused by intermittent periods of rainfall. The proposed paradigm is based on the stage wise implementation of non-linear finite element (FE) analysis, with each stage representing a distinct phase of a typical wet-dry cycle. The associated boundary conditions have been constituted to realize the influence of various meteorological elements such as rain, wind, relative humidity and temperature on the exposed concrete surface. The reliability of the developed scheme has been demonstrated through its application for the simulation of experimentally recorded moisture profiles reported in published literature. A sensitivity analysis has also been carried out to study the influence of critical material properties on simulated results. The proposed scheme is vital to the service life modelling of concrete structures in tropical climates which largely remain exposed to the action of alternating rains.

• Advances in concrete construction
• /
• v.3 no.1
• /
• pp.39-54
• /
• 2015

Relative humidity and strains within a massive concrete cylinder (${\varphi}450mm{\times}900mm$) in the drying and the re-saturating process were measured for elucidating the process of ASR surface cracking in concrete. The expansion behavior of mortars in dry atmospheres with various R.H. values and the resaturating process was revealed. Non- or less-expansive layers were formed in near-surface regions in the concrete cylinder in the drying process, but ASR expansions actively progressed in inner portions. After resaturating, R.H. values of near-surface regions rapidly increased with time, but expansions in the regions were found to be very small. However, in the middle portions, of which R.H. values were kept 80% ~ 90% R.H. in the drying process, expansion actively progressed, resulting in further development of surface cracks in the re-saturating process.

• Korean Journal of Food Science and Technology
• /
• v.31 no.6
• /
• pp.1589-1595
• /
• 1999

Reverse osmosis(RO) and rotary evaporation, freezer drying and spray drying as concentration and dehydration methods were, respectively, employed to investigate their effect on the flavor quality of ginger powder. Rotary evaporation and spray drying methods were more effective to restrict the browning of ginger powder than RO and freezer drying methods. Concentration methods had no effect on the free amino acids and free sugar contents of ginger powder, but freezer drying resulted in the less quality loss than spray drying. And the powder prepared from enzymatically hydrolyzed extract contained less crude protein, crude ash, browning and the changes in free amino acids, but had more the crude fat, solubility and free sugars than that from ginger extract obtained by filter press. Sensory results indicated that quality of ginger powder prepared by RO concentration and freeze drying of enzymatically hydrolyzed extract was as good as that without enzyme hydrolysis

• Food Science and Preservation
• /
• v.17 no.4
• /
• pp.478-486
• /
• 2010

The qualities of ginger prepared by an MPD (molecular press dehydration) method using maltodextrin, or dried using reused dehydration liquid, or prepared by freeze-drying or hot-air drying, were compared in terms of approximate overall composition, color, water absorption index, water solubility index, total sugar level, reducing sugar concentration, antioxidant activity, and gingerol content. The approximate composition of ginger prepared by the MPD method was lower in overall biochemical content than were those of gingers prepared using other methods. Ginger prepared by the MPD method retained the original ginger color. The water absorption and solubility index of ginger prepared by the MPD method (using maltodextrin) were better than those of gingers dried using other methods. The total sugar content did not change noticeably upon processing. The reducing sugar content of ginger prepared by hot-air drying was low. The antioxidant activity of ginger prepared by the MPD method was higher than that of freeze-dried and hot air-dried ginger samples, with values lower than those of BHA (3(2)-t-Butyl-4-hydroxyanisole) and BHT (2,6-Di-tert-butyl-4-methylphenol). The gingerol content of ginger prepared by the freeze-drying method was higher than that of gingers prepared by other methods. However, ginger constituents were present in the dehydration liquid used in the MPD method. The results indicate that both the MPD method (using maltodextrin) and the use of reused dehydration liquid are efficient methods by which ginger can be dried.

• Steel and Composite Structures
• /
• v.49 no.3
• /
• pp.337-348
• /
• 2023

Successive wetting and drying cycles of concrete due to weather changes can endanger the safety of engineering structures over time. Considering wetting and drying cycles in concrete tests can lead to a more correct and reliable design of engineering structures. This study aims to provide a model that can be used to estimate the resistance properties of concrete under different wetting and drying cycles. Complex sample preparation methods, the necessity for highly accurate and sensitive instruments, early sample failure, and brittle samples all contribute to the difficulty of measuring the strength of concrete in the laboratory. To address these problems, in this study, the potential ability of six machine learning techniques, including ANN, SVM, RF, KNN, XGBoost, and NB, to predict the concrete's tensile strength was investigated by applying 240 datasets obtained using the Brazilian test (80% for training and 20% for test). In conducting the test, the effect of additives such as glass and polypropylene, as well as the effect of wetting and drying cycles on the tensile strength of concrete, was investigated. Finally, the statistical analysis results revealed that the XGBoost model was the most robust one with R2 = 0.9155, mean absolute error (MAE) = 0.1080 Mpa, and variance accounted for (VAF) = 91.54% to predict the concrete tensile strength. This work's significance is that it allows civil engineers to accurately estimate the tensile strength of different types of concrete. In this way, the high time and cost required for the laboratory tests can be eliminated.

• Journal of the Korean Wood Science and Technology
• /
• v.15 no.3
• /
• pp.56-67
• /
• 1987

Plywoods used for construction as a decorative interior material are inflammable and can make fire accidents, causing destruction of human life and property. Therefore, it is indeed required to make fire-retardant treated plywood. In this study, 3.7mm yellow meranti plywoods were soaked in 18% boric acid solutions and tap water by hot-cold bath for 1/2, 2/2, 4/2, 6/2 hours and redrying of treated plywoods was carried out by press drying at the platen temperature of 110, 130, 160, $180^{\circ}C$ and then it was conducted to investigate solution absorption, drying rates, dynamic young's modulus. specific gravity and fire-retardant factors such as burning point, flame spread length. flame exhausted time, back side carbonized area and weight loss by treating time, treating solutions and platen temperature. The results are as follows; 1. When plywood was impregnated with the hot bath temperature of $70^{\circ}C$ for 1. 2, 4, 6 hours and the cold bath temperature of $15^{\circ}C$ for 2 hours respectively, retentions of boric acid were 1.565, l.597, 1.643, 1.709kg/$(30cm)^3$ and all of them exceeded the minimum retention [1.125kg/$(30cm)^3$] even in the shortest treatment. 2. In hot-cold bath method for 1/2 hours, the drying rates of treated plywood remarkably increased with the extension of platen temperature of 110, 130, 160, $180^{\circ}C$ and the values of boric acid treated plywood were 5.900, 10.196, 45.42, 54.958m.c%/min and the values of water treated plywood were 6.014, 12.373, 46.520, 55.730m.c%/min and drying rates of water treated plywood were faster than those of boric acid treated plywood. 3. The values of boric acid treated plywoods in dynamic young's modulus were widely higher than those of water treated plywoods. And it can be observed that there were highly significant differences for treating time between dynamic young's modulus, and the values of boric acid plywoods increased with the extension of treating time but on the contrary water treated plywoods were decreased values with prolonged time 4. It was observed that there were highly significant differences for platen temperature between dynamic young's modulus. When the values of water treated plywoods in dyna nic young's modulus were abruptly decreased according to the rise of platen temperature. boric acid treated plywoods showed rather increased values at $160^{\circ}C$ of platen temperature. And in 2- way interactions, there were also highly significant for dynamic young's modulus between treating time x treating solutions and platen temperature x treating solutions. 5. Correlation coefficients of fire-retardant factors were shown in table 5. It could be recognized that there were close correlations between the treating solutions and burning point, flame spread length, back side carbonized area, flame exhausted time and weight loss, but there was no correlation between fire-retardant factors and treating time and platen temperature. 6. From table 6, it can be observed that there were highly significant differences for burning point, flame spread length, flame exhausted time, back side carbonized area, weight loss between treating solutions. And in 2-way interactions, there were highly significant for burning point, flame spread length, weight loss between treating time $\times$ treating solutions.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.44 no.5
• /
• pp.54-62
• /
• 2012

The main role of surface sizing of linerboard is to improve surface and strength properties. Since surface sizing solution is applied on once dried web, substantial amount of drying energy is required. Saving of the drying energy associated with surface sizing can be made by increasing the solids content of the starch solution in size press. Therefore, it is highly desirable to develop low viscosity starches for surface sizing. A low viscosity oxidized starch was prepared and compared its effect of surface sizing with a conventional oxidised starch. Results showed increase in solids content of the starch solution decreased evaporation energy and drying time. Low viscosity starch penetrated deeper into paper and this improve various mechanical properties of linerboard.

• Journal of Fisheries and Marine Sciences Education
• /
• v.22 no.4
• /
• pp.501-507
• /
• 2010

The ceramic contained paint was made to replace the lead sinker for gill-net with coated lead sinker. The ceramic contained paints were coated in various conditions on the lead sinker with 19g of weight and the optimal coating condition was studied. The adaptability of the coated lead sinker was checked through the anti durability test and fishing operation with gill-net. The case of "Main material 70 wt% + Urethane thinner 30 wt% (Main material 700 $m{\ell}$ + Thinner 300 $m{\ell}$)" showed the best in the coating characteristics depending on the combination ratio of the ceramic paint contained. The coated lead sinker dried at $100^{\circ}C$ inside oven was superior to the drying in the room temperature in its surface glossiness and anti durability and faster drying time than the one dried in normal temperature. The quadruple layers of coating on lead sinker with 4 times of dipping and drying application showed the super anti durability in the coating characteristics depending on the frequency of dipping. When press is applied to the coated lead sinker, the coated layer is not detached from the sinker. In addition, the coated lead sinker was not damaged or peeled at the fishing operation about 2 months in various depths within 50m and by the materials at the bottom (sand, stone and gravel stone) and it was in good condition.