• Transactions of Materials Processing
• /
• v.19 no.7
• /
• pp.399-404
• /
• 2010

We propose an analysis model for simulating the detailed procedure of pore closing in open die forging of shafts. In the analysis model, an artificial symmetric plane is used, on which initial pores are located to be traced. The analysis model is employed to carry out three-dimensional simulation of pore closing in shaft free forging by both conventional free forging press and radial forging machine. With this result, two typical types of free forging equipment for manufacture of shafts are compared in detail. It has shown that the radial forging machine is much superior to the conventional open die forging press especially in pore closing under high hydrostatic pressure with sound strain.

• Korean Journal of Materials Research
• /
• v.13 no.6
• /
• pp.374-380
• /
• 2003

The effect of forging parameters, including different forging stock, strain rate and strain, on the mechanical properties of hot-forged Al 6061-T6 was investigated. The forging was conducted using either hydraulic press, crank press or hammer press, respectively, at a forging temperature of $400^{\circ}C$. When using an extruded bar as a forging stock, the tensile strength was lower for the specimens prepared by hammer forging than those by crank press forging. It was found that the coarsening of recrystallized grain was responsible for the decrease in tensile strength with hammer forging. Systematic studies on the effects of strain and strain rate on the tensile properties of hot-forged Al 6061-T6 products using extruded bar as a forging stock further suggested that the coarsening of recrystallized grains and$ Mg_2$Si precipitates complexed the observed trends in the tensile behavior. In case of hot forging with continuous cast bar as a forging stock, on the other hand, the mechanical properties of the specimen were largely improved with hammer press compared to those with crank press, which appeared to be due to the homogenization of microstructure.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.216-220
• /
• 2003

Most important for meaningful forging simulation is the determination of correct process parameters. In addition a check and a compensation of the data base after the comparison between experiments and the computation of the developed process is necessary. The existence of a systematic process parameter data bank for special kinds of forming process in combination with forging specific simulation lifts the value of the products. Finite volume method is applied to simulate the hot forging process to investigate the defects for the automobile product. Three typical forging processes have been investigated; Extrusion by hydrolic press, Upsetting by crank press and Inclined upsetting by hammer press. Simulated result has compared with the experiment and provided a direction to improve the process.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1995.03a
• /
• pp.31-40
• /
• 1995

Powder metallurgy process has many advantages such as hight efficientyof material, mass productivity and complex shape production with good mechanical properties. Among the powder forming processes, incremental forging allows the consolidation to be achieved with amaller force then those required by conventional forging. In particular the proces known as rotary forging is an unique and prodominant process known as rotary forging is an unique and prodominant process in which the working constraints approximate to those in normal closed die forging. This study is concerned with the powder compaction by rotary forging process. An experimental rotary forging press with 500kN load capacity has been developed, which is equippe dwith the rotational conicla die inclined to the central axis of the press at arbitrary angle. It is found that the highly densified P/M parts can be obtained by rotary forging process and the material properties are superior to those of the conventrional sintered parts. The detailedcomparision of the mechanical properties by rotary forging process with those by conventional process are given.

• Journal of Drive and Control
• /
• v.19 no.4
• /
• pp.10-18
• /
• 2022

Air-drop hammer press and counterblow hammer press are widely used power-drop forging hammersemploying different forging blow mechanisms. It is important and necessary to analyze mechanical vibrations of these two different hammers in their forging processes in order to develop high performance forging hammers. In this study, these two forging hammers were mathematically modelled as mass-spring-damper systems. For these two different types of forging hammers, the forging efficiency and mechanical vibrations due to hammer forging blow were theoretically analyzed and compared. The force transmitted to the ground was also determined and compared. Especially, effects of mass ratio and restitution coefficient on forging efficiency were investigated.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1995.06a
• /
• pp.135-144
• /
• 1995

Cold Forging has advantage in high accuracy and short working time. However large-skzed and complicated parts are difficult to process with cold forging. Thus large-sized and complicated parts have been processed with two pieces, or combind forging that is hot forging in addition to cold sizing. Recently, large-sized and complicated parts can be manufactured with cold forging alone by advanced cold forging technology using the long-stroke press. In this paper, cold forging technology of large-sized and complicated parts are investigated, including tripod slide housing for constant velocity joint and drive shaft for starter.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.1
• /
• pp.86-91
• /
• 2006

Magnesium alloys have been widely used for many structural components of automobiles and aircraft because of high specific strength and good castability in spite of hexgonal closed-packed crystal structure of pure magnesium. In this paper, FE analysis was executed about the formability of AZ3l magnesium alloy on press forging process. For this, the variation of sheet temperature, distribution of punch force and the effect of heat transfer and friction between punch and sheet on the forming characteristics during press forging of AZ31 has been analyzed by finite element analysis. In order to obtain temperature dependence of material characteristics, uniaxial tension tests at elevated temperature were done under temperature of $100^{\circ}C\~ 500^{\circ}C$.

• Transactions of Materials Processing
• /
• v.3 no.3
• /
• pp.271-281
• /
• 1994

Titanium-6242 $({\alpha}+{\beta})$ alloy has been used for aircraft engine components such as disks and blades, because it has an excellent strength/weight ratio at high temperatures. When this material is forged to manufacture disks, process parameters should be carefully designed to control strain and temperature distributions within the process windows by which desirable mechanical properties can be produced. In the present investigation, it was intended to design the process parameters for a conventional hot forging of this material by using a rigid-thermoviscoplastic finite element analysis technique. It was assumed that the process was performed by a screw press which is capable of maintaining a constant ram speed during loading. From the analysis results, it was found out that the initial temperature of the workpiece and the die shape were important parameters to control the forging process. In result, these parameters were properly designed for hot forging of a disk with specific dimensions.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1995.06a
• /
• pp.47-54
• /
• 1995

Rotary forging process has many advantages such as compacting of machine, low price of facilities and good quality of products. The last presented was a technical report about rotary forging press in the 100-ton class, which has the only orbital motion limited to the forming of axisymmetric parts. In this paper, the newly developed rotary forging press is introduced. The maximum capacity of forming load is 280 ton and five locking motion, this is, orbital, straight pivot, spiral and two kinds of clover can be available. This machine consists of transmission, double eccentric bush, rocking shaft, die set and hydraulic unit. Especially, the supports of rocking shaft and double eccentric bush are so crucial that hydrostatic bearings are adopted. Finally, it is expected that the technical know-how obtained in this research can be applied to the manufacturing of the another machine with large capacity.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1996.03b
• /
• pp.110-120
• /
• 1996

A crank-slider mechanism is driven by the rotating disk with are crank-pin guide to be applied to the deep drawing and cold forging presses. Load characteristics for different presses are summarized to see the basics of deep drawing of sheet metal and forging in terms of load-stroke relationship. Several types of conventional deep drawing presses are also shown to be compared with the ratating disk-types press. Kinematic performances by thearc guide driving mechanism are anlayzed in terms of load capaicty, stroke, and slide velocity characteristics, and they are compared with those by conventional driving , e.g. Niagara-typepress and so on. Kinematically better performances is shown by arc guide drive than those by conventional ones. The new driving mechanism is also proven to be one of the best for mass production press in terms of short cycle time. Possible applications of the arc guide press to deep drawing and cold forging work are in terms of kinematics and load capacity.