• 한국주조공학회지
• /
• 제17권1호
• /
• pp.28-35
• /
• 1997

SiC whisker and $Al_2O_3-SiO_2$ short fiber reinforced AC8A, AC8B and AC8B(J) marix composites were fabricated by squeeze casting method. Preform deformation, change of reinforcement volumefraction and formation of macro-segregation in two composites were investigated by using micro Vickers hardness test, analysis of macro and micro structures with OM, SEM and EDAX. $Al_2O_3-SiO_2$ short fiber preform manufactured with 5% $SiO_2$ binder in this study was considerably deformed and cracked, nevertheless, the short fibers were distributed homogeneously in the composites. In SiC whisker reinforced composites, on the other hand, preform deforming and cracking were not occurred, however, macro segregation zone formed along the infiltration routes by interface reaction during infiltration of molten metal into the preform was observed at center-low area in the composites. The decrease of hardness in the macro segregation zone resulted from the depletion of Si and Mg atoms.

• 한국전산유체공학회지
• /
• 제18권4호
• /
• pp.69-73
• /
• 2013

Mass manufacturing of optical fiber includes the process of very thin glass fiber drawing by heating and softening the high purity silica preform and applying the draw tension on the softened tip of preform neck-down profile in a draw furnace. In this computational study, this process is numerically modeled with simplified geometry of the draw furnace which is comprised of essential parts such as concentric graphite heater, muffle tube, and insulation surrounding the heater. The iterative computational scheme is employed between one-dimensional model of neck-down profile prediction and two-dimensional axisymmetric thermo-fluid CFD computation of radiative heating and working gas convection. The computational results show the experimentally observed neck-down profile in heated section of preform, while yielding the reasonable values of draw tension and heater wattage. Also, this study analyzes and discusses the effects of heating conditions such as heater length and temperature on several important aspects of glass fiber drawing process.

• 한국산학기술학회논문지
• /
• 제11권1호
• /
• pp.1-6
• /
• 2010

본 연구에서는 성형해석 및 실험적 방법을 통하여 페트 용기의 두께 편차를 최소화하기 위한 프리폼 최적화 설계를 수행하였다. 사출성형과정을 정확하게 묘사하기 위하여 3차원 모델을 이용하여 충진, 보압 및 냉각해석을 통하여 최적의 프리폼 설계변수를 설정하였으며, 이 결과를 이용하여 블로우 성형해석을 수행하였다. 성형해석결과를 평가하기 위한 사출성형 및 블로우 성형실험을 수행하였으며, 실험결과와 해석결과는 정성적으로 일치하는 것을 확인하였다. 이러한 실험결과 데이타를 설계에 반영함으로서 최적의 프리폼 형상을 얻을 수가 있었다.

• 소성∙가공
• /
• 제13권7호
• /
• pp.635-641
• /
• 2004

Today the specific outputs of modern supercharger DI diesel engine for passenger cars reach values exceeding 50kw/1. By development of the articulated piston, specific output of up to 70kw/1 are sought. In doing so, peak cylinder pressure increases from the current 14-16MPa to 18-20MPa. The Articulated piston was composed Al cast skirt part and steel forged crown part. We have the target fer the design of forging process and die of the steel forged crown part. The design parameters of the forging process of the piston were obtained by the forging industry experiences and our experimental data and analysis result of finite element simulation. Especially, the design parameter of preform in blocker die was decided by finite element simulation using numerical package DEFROM3D. And also we can verify the design parameter by conducting visio-plasticity test using plasticine material. When we compared the results of analysis and experiment, a metal flow and load curve showed good agreement. Through this research, we could design optimal preform shape of articulated piston for this supercharged DI diesel engine.

• Composites Research
• /
• 제32권1호
• /
• pp.56-64
• /
• 2019

본 연구에서는 탄화수소를 이용한 탄소/탄소 복합재의 화학기상침투 공정에 대해 프리폼의 밀도 변화, 공극률 변화와 다단계 화학반응을 고려한 수치해석 모델을 개발하였다. 프리폼을 다공성 매질로 가정하여 공극률에 따른 확산 및 유동 특성의 변화를 도입하였다. 검증을 위하여 프리폼 내부 유동이 0으로 제약된 경우와 유동해석을 통해 계산된 경우에 대해 수치해석을 수행하였으며, 해석 결과가 문헌의 실험치와 일치하는 것을 보였다.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 춘계학술발표대회 논문집
• /
• pp.181-183
• /
• 2002

The accurate permeability for preform is critical to model and design the impregnation of fluid resin in the composite manufacturing process. In this study, the in-plane and transverse permeability for a woven fabric are predicted numerically through the coupled flow model which combines microscopic with macroscopic flow. The microscopic and macroscopic flow which are flows within the micro-unit and macro-unit cell, respectively, are calculated by using 3-D CVFEM(control volume finite element method). To avoid checker-board pressure field and improve the efficiency on numerical computation, A new interpolation function for velocity is proposed on the basis of analytic solutions. The permeability of plain woven fabric is measured through unidirectional flow experiment and compared with the permeability calculated numerically. Based on the good agreement of the results, the relationships between the permeability and the structures of preform such as the fiber volume fraction and stacking effect can be understood. The reverse and the simple stacking are taken in account. Unlike past literatures, this study is based on more realistic unit cell and the improved prediction of permeability can be achieved. It is observed that in-plane flow is more dominant than transverse flow in the real flow through preform and the stacking effect of multi-layered preform is negligible. Consequently, the proposed coupled flow model can be applied to modeling of real composite materials processing.

• 대한기계학회논문집A
• /
• 제35권1호
• /
• pp.1-10
• /
• 2011

본 논문은 등가정하중을 이용하여 단조공정의 예비성형체 및 빌렛의 형상설계를 위한 최적화 방법을 제안한다. 단조공정에서 예비성형체의 형상은 최종 성형품의 품질을 결정하는데 중요한 역할을 한다. 본 연구는 빌렛 및 예비성형체의 형상을 설계하기 위하여 등가정하중법을 사용하였다. 등가정하중법은 비선형 동적하중을 등가정하중으로 변환하고 여기서 구한 등가정하중을 이용하여 선형 응답 최적화를 수행하는 방법이다. 설계변수의 갱신은 선형 응답 최적화와 비선형 해석을 통하여 이루어진다. 본 논문에 포함된 예제는 원하는 단조품의 생산을 위한 최적의 예비성형체와 빌렛의 형상을 도출하여 제안한 방법의 유용성을 검증한다. 비선형 해석과 선형 응답 최적화는 각각 LS-DYNA와 NASTRAN을 사용하였다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 추계학술대회 논문집
• /
• pp.370-373
• /
• 2008

Small size gas turbine disk requires good mechanical strength and creep properties at high temperature. In this study, Waspaloy was used as a superalloy to satisfy these specifications. The control of microstructure was needed to satisfy material properties at high temperature. In order to do this, we studied forging conditions and material analysis. Therefore die and preform design conducted so that hot forged gas turbine disk could have a good microstructure. The die and preform shapes are designed with consideration of the predefined hydraulic press capacity and the microstructure of forging product. Also we carried out the hot compression test for Waspaloy in various test conditions. From these results, we obtained the forging conditions as material temperature, die velocity etc. To verify these forging conditions, we conducted FE simulations by means of the DEFORM 2D-HT. In this study, the hot closed die and preform designs were completed to offer high temperature material properties of a small size gas turbine.

• 한국섬유공학회:학술대회논문집
• /
• 한국섬유공학회 2003년도 봄 학술발표회 논문집
• /
• pp.191-194
• /
• 2003

In this study, permeability tensor is computed for a three dimensional braided preform by applying a FVM to a unit cell. It is evident that resin will flow through the inter-tow and the intra-tow regions when pressure gradient is applied to the resin. The intra-tow region in the braided preform is regarded as not only an impermeable solid but also a permeable porous media. When the intra-tow region is excluded from domain of flow analysis in the case of the impermeable solid, the Stokes equation is computer for only inter-tow region. (omitted)

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 추계학술대회논문집
• /
• pp.25-28
• /
• 2003

The articulated piston that was used to more powerful diesel engine was composed by Al casted skirt part and steel forged crown part. this paper has the target to design the forging process of crown part. The parameters of piston design and forging process design were gotten based on work experience, experimental data, approximately calculated data and finite element analysis. Preform design parameter decided using the Taguchi method. Through this research, could design optimal shape of preform and produce prototype of the articulated piston