• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.9
• /
• pp.60-67
• /
• 2007

A signal conditioning circuit for capacitive displacement sensors was developed using a high frequency modulation/demodulation method, and its performance was evaluated. Since capacitive displacement sensors can achieve high resolution and linearity, they have been widely used as precision sensors within the range of several hundred micrometers. However, they inherently have a limitation in low frequency range and some nonlinearity characteristics and so a specially designed signal conditioning circuit is needed to handle these properties. The developed signal processing circuit consists of three parts: linearization, modulation/demodulation, and nonlinearity compensation. Each part was constructed discretely using several IC chips and passive elements. An evaluation system for precision displacement sensors was developed using a laser interferometer, a precision stage, and a PID position controller. The signal processing circuit was tested using the evaluation system in the respect of resolution, repeatability, linearity, and so on. From the experimental results, we know that a highly linear voltage output can be obtained successfully, which is proportional to displacement and the nonlinearity of output is less than 0.02% of full range. However, in the future, further investigation is required to reduce noise level and phase delay due to a low-pass filter. The evaluation system also can be applied effectively to calibration and evaluation of precision sensors and stages.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.15 no.5
• /
• pp.160-168
• /
• 2011

As importance of the field of maintenance and management come to the fore because of collapses of the Seongsu bridge and the Sampoong department store, "Special Act for the Safety Control of Public Structures" was established in 1995 and the major maintenance and management system began taking effect "Detailed inspection and Precision safety diagnosis". However, a technical standard of "Detailed inspection and Precision safety diagnosis" was low because its history was not long, and also the results of research were not enough so anxiety for "Insufficient Detailed inspection and Precision safety diagnosis" was continuously left. While its evaluation system introduced in 2002, the ratio of "Insufficient Detailed inspection and Precision safety diagnosis" has been getting lower. However, according to the evaluation result after carrying out "Detailed inspection and Precision safety diagnosis" recently, it seems difficult to become lower for the ratio of "Insufficient Detailed inspection and Precision safety diagnosis" in future. Therefore, it is considered of questionary survey of the concerned organization and the mechanism side in connection with "Insufficient Detailed inspection and Precision safety diagnosis". So it is arranged the fundamental problems caused by an "Insufficient Detailed inspection and Precision safety diagnosis" that is to show the improving direction of the existing evaluation system in a based on this.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.25 no.4
• /
• pp.181-199
• /
• 2022

This study presented a methodology for evaluating the performance of the lane departure warning system was derived by calculating the relationship between the behavior information of the car and the location of the high-precision map using a high-precision map. The evaluation criteria of the mood and lane departure warning system for the installation of road markings in Korea were analyzed, a high-precision map was constructed to meet the evaluation criteria, and an evaluation system was constructed to verify the proposed methodology. Evaluation of lane departure warning systems using high-precision maps can be quantified and applied to various road environments through accurate location-based comparative analysis and reduced manual post-processing work time to confirm evaluation results.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.7
• /
• pp.94-100
• /
• 2010

This paper describes the design and evaluation procedure of an ultra-precision rotary table for freeform generating machined tools. Design of the thrust and journal hydrostatic bearings and experimental evaluation of the table were performed. To get the compact size and less lost motion direct drive servomotor with ultra precision encoder. From the considered design, following performance were confirmed by experiment. The total stiffness of the prototype rotary table was 483.6 $N/{\mu}m$ and 97.6 $N/{\mu}m$ for axial and radial direction, respectively. Rotational accuracy of the table was investigated by capacitive sensor and reversal measurement technique, and 0.10 ${\mu}m$ radial direction and 0.05 ${\mu}m$ axial direction of the rotational accuracy were confirmed. The micro resolution of the table was also investigated with displacement of capacitive sensor, and $0.5/10000^{\circ}$ of micro resolution was confirmed. Index accuracy of the table was evaluated by the autocollimator and polygon mirror, and the $\pm0.39$ arcsec accuracy and $\pm0.16$ arcsec repeatability of the table were confirmed. Those are under the general requirements of ultra precision rotary tables for freeform generating machined tools.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2013.05a
• /
• pp.461-462
• /
• 2013

• International Journal of Precision Engineering and Manufacturing
• /
• v.8 no.3
• /
• pp.50-53
• /
• 2007

Improving the reliability or long-term dependability of a system requires a different approach from the previous emphasis on short-term concerns. The purpose of this paper is to present a reliability evaluation method for an oil cooler intended for high-precision machining centers. The oil cooler system in question is a cooling device that minimizes the deformation caused from the heat generated by driving devices. This system is used for machine tools and semiconductor equipment. We predicted the reliability of the system based on the failure rate database and conducted the reliability test using a test-bed to evaluate the life of the oil cooler. The results provided an indication of the reliability of the system in terms of the failure rate and the MTBF of the oil cooler system and its components, as well as a distribution of the failure mode. These results will help increase the reliability of oil cooler systems. The evaluation method can also be used to determine the reliability of other machinery products.

• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.3
• /
• pp.191-197
• /
• 1993

In this paper, experimental studies are mainly carried out for the evaluation of precision cutting performance of a machine tool spincle running at high speed with the low load, in consideration of the bending vibration characteristics. As a result a process in presented for the practical application in the machine tools industry to evaluate the cutting performance in design stage of spindles.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.11a
• /
• pp.363-364
• /
• 2008

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.05a
• /
• pp.1085-1086
• /
• 2012

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.05a
• /
• pp.747-748
• /
• 2012