• Bulletin of the Korean Space Science Society
• /
• 1993.10a
• /
• pp.17-17
• /
• 1993

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70${\pm}$1.32mmHg/min)compared to CF dialyzers(4.32${\pm}$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500,550,570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500,550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100,300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3,000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.

• Asia pacific journal of information systems
• /
• v.20 no.3
• /
• pp.139-166
• /
• 2010

The supply chain management (SCM) systems have emerged as strong managerial tools for manufacturing firms in enhancing competitive strength. Despite of large investments in the SCM systems, many companies are not fully realizing the promised benefits from the systems. A review of literature on adoption, implementation and success factor of IOS (inter-organization systems), EDI (electronic data interchange) systems, shows that this issue has been examined from multiple theoretic perspectives. And many researchers have attempted to identify the factors which influence the success of system implementation. However, the existing studies have two drawbacks in revealing the determinants of systems implementation success. First, previous researches raise questions as to the appropriateness of research subjects selected. Most SCM systems are operating in the form of private industrial networks, where the participants of the systems consist of two distinct groups: focus companies and vendors. The focus companies are the primary actors in developing and operating the systems, while vendors are passive participants which are connected to the system in order to supply raw materials and parts to the focus companies. Under the circumstance, there are three ways in selecting the research subjects; focus companies only, vendors only, or two parties grouped together. It is hard to find researches that use the focus companies exclusively as the subjects probably due to the insufficient sample size for statistic analysis. Most researches have been conducted using the data collected from both groups. We argue that the SCM success factors cannot be correctly indentified in this case. The focus companies and the vendors are in different positions in many areas regarding the system implementation: firm size, managerial resources, bargaining power, organizational maturity, and etc. There are no obvious reasons to believe that the success factors of the two groups are identical. Grouping the two groups also raises questions on measuring the system success. The benefits from utilizing the systems may not be commonly distributed to the two groups. One group's benefits might be realized at the expenses of the other group considering the situation where vendors participating in SCM systems are under continuous pressures from the focus companies with respect to prices, quality, and delivery time. Therefore, by combining the system outcomes of both groups we cannot measure the system benefits obtained by each group correctly. Second, the measures of system success adopted in the previous researches have shortcoming in measuring the SCM success. User satisfaction, system utilization, and user attitudes toward the systems are most commonly used success measures in the existing studies. These measures have been developed as proxy variables in the studies of decision support systems (DSS) where the contribution of the systems to the organization performance is very difficult to measure. Unlike the DSS, the SCM systems have more specific goals, such as cost saving, inventory reduction, quality improvement, rapid time, and higher customer service. We maintain that more specific measures can be developed instead of proxy variables in order to measure the system benefits correctly. The purpose of this study is to find the determinants of SCM systems success in the perspective of vendor companies. In developing the research model, we have focused on selecting the success factors appropriate for the vendors through reviewing past researches and on developing more accurate success measures. The variables can be classified into following: technological, organizational, and environmental factors on the basis of TOE (Technology-Organization-Environment) framework. The model consists of three independent variables (competition intensity, top management support, and information system maturity), one mediating variable (collaboration), one moderating variable (government support), and a dependent variable (system success). The systems success measures have been developed to reflect the operational benefits of the SCM systems; improvement in planning and analysis capabilities, faster throughput, cost reduction, task integration, and improved product and customer service. The model has been validated using the survey data collected from 122 vendors participating in the SCM systems in Korea. To test for mediation, one should estimate the hierarchical regression analysis on the collaboration. And moderating effect analysis should estimate the moderated multiple regression, examines the effect of the government support. The result shows that information system maturity and top management support are the most important determinants of SCM system success. Supply chain technologies that standardize data formats and enhance information sharing may be adopted by supply chain leader organization because of the influence of focal company in the private industrial networks in order to streamline transactions and improve inter-organization communication. Specially, the need to develop and sustain an information system maturity will provide the focus and purpose to successfully overcome information system obstacles and resistance to innovation diffusion within the supply chain network organization. The support of top management will help focus efforts toward the realization of inter-organizational benefits and lend credibility to functional managers responsible for its implementation. The active involvement, vision, and direction of high level executives provide the impetus needed to sustain the implementation of SCM. The quality of collaboration relationships also is positively related to outcome variable. Collaboration variable is found to have a mediation effect between on influencing factors and implementation success. Higher levels of inter-organizational collaboration behaviors such as shared planning and flexibility in coordinating activities were found to be strongly linked to the vendors trust in the supply chain network. Government support moderates the effect of the IS maturity, competitive intensity, top management support on collaboration and implementation success of SCM. In general, the vendor companies face substantially greater risks in SCM implementation than the larger companies do because of severe constraints on financial and human resources and limited education on SCM systems. Besides resources, Vendors generally lack computer experience and do not have sufficient internal SCM expertise. For these reasons, government supports may establish requirements for firms doing business with the government or provide incentives to adopt, implementation SCM or practices. Government support provides significant improvements in implementation success of SCM when IS maturity, competitive intensity, top management support and collaboration are low. The environmental characteristic of competition intensity has no direct effect on vendor perspective of SCM system success. But, vendors facing above average competition intensity will have a greater need for changing technology. This suggests that companies trying to implement SCM systems should set up compatible supply chain networks and a high-quality collaboration relationship for implementation and performance.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.7 no.3
• /
• pp.108-128
• /
• 2002

In order to investigate the ecological characteristics of phytoplankton communities around a nuclear power plant in Gori coastal waters of the South East Sea, Wolseong and Uljin coastal waters of the East Sea and Younggwang coastal waters of the Yellow Sea, the standing crops and chlorophyll-$\alpha$ concentrations of phytoplankton were studied during 1992~1996 and the relationships between standing crops and environmental variables were analyzed. The concentrations of nitrogenous nutrients were on average 0.101, 0.094, 0.072 and 0.108mg/$\ell$ and those of phosphorus were on average 0.007, 0.008, 0.006 and 0.009mg/$\ell$ in Gori, Wolseong, Uljin and Younggwang, respectively. The N:P ratios were highly variable, ranging from 3.2 to 57.3, from 3.1 to 109.0, from 2.6 to 102.0 and from 1.0 to 165.0 in Gori, Wolseong, Uljin and Younggwang, respectively. The concentrations of suspended solids were on average 18.7, 16.7, 11.6 and 52.7mg/$\ell$ and transparencies were on average 3.8, 5.4, 7.9 and 0.7 m in Gori, Wolseong, Uljin and Younggwang, respectively. Total standing crops of phytoplankton averaged 710,659, 687,508, 656,245 and 1,278,173cells/$\ell$ in Gori, Wolseong, Uljin and Yaunggwang, respectively. The standing crops of microplankton(>20${\mu}{\textrm}{m}$) averaged 357,546, 333,638, 276,407 and 592,975cells/$\ell$ those of nanoplankton(<20${\mu}{\textrm}{m}$) averaged 353,113, 353,870, 379,838 and 574,563cells/$\ell$ in Gori, Wolseong, Uljin and Younggwang, respectively. While standing crops of diatoms were averaged 282,009, 284,710, 238,758 and 574,563 cells/$\ell$, those of dinoflagellates were averaged 46,079, 35,401, 32,906 and 16,749 cells/$\ell$ in Gori, Wolseong, Uljin and Younggwang, respectively. The seasonal standing crops of diatoms in Gori, Wolseong and Uljin were higher in Spring than other seasons, but were lower in Summer than other seasons in Younggwang. The seasonal standing crops of dinoflagellates in Gori and Younggwang were higher in Summer than other seasons, but were higher in Autumn than other seasons in U]jin. Average of chlorophyll-$\alpha$ concentrations ranged from 2.16 to 4.28$\mu\textrm{g}$/$\ell$ in 4 study areas with the highest concentration occurred in Younggwang. Indices of species diversity ranged from 2.11 to 2.24 in 4 study areas. While community structures of phytoplankton were unstable during winter and stable during summer in Gori, Wolseong and Uljln coastal waters, those of phytoplankton were stable during winter and summer than during spring and autumn in Yaunggwang. The analysis results of Pearson product moment correlation coefficient between standing crops and environmental variables showed that distributions of standing crops were affected by transparencies, suspended solids, and some nutrient(N $O_3$$^{[-10]}$ -N, P $O_4$$^{3-}$-P), even though the degree of influences were a little different according to the season and the surveyed zone.

• Radiation Oncology Journal
• /
• v.19 no.1
• /
• pp.66-73
• /
• 2001

Purpose : For the research of Boron Neutron Capture Therapy (BNCT), fast neutrons generated from the MC-50 cyclotron with maximum energy of 34.4 MeV in Korea Cancer Center Hospital were moderated by 70 cm paraffin and then the dose characteristics were investigated. Using these results, we hope to establish the protocol about dose measurement of epi-thermal neutron, to make a basis of dose characteristic of epi-thermal neutron emitted from nuclear reactor, and to find feasibility about accelerator-based BNCT. Method and Materials : For measuring the absorbed dose and dose distribution of fast neutron beams, we used Unidos 10005 (PTW, Germany) electrometer and IC-17 (Far West, USA), IC-18, ElC-1 ion chambers manufactured by A-150 plastic and used IC-l7M ion chamber manufactured by magnesium for gamma dose. There chambers were flushed with tissue equivalent gas and argon gas and then the flow rate was S co per minute. Using Monte Carlo N-Particle (MCNP) code, transport program in mixed field with neutron, photon, electron, two dimensional dose and energy fluence distribution was calculated and there results were compared with measured results. Results : The absorbed dose of fast neutron beams was $6.47\times10^{-3}$ cGy per 1 MU at the 4 cm depth of the water phantom, which is assumed to be effective depth for BNCT. The magnitude of gamma contamination intermingled with fast neutron beams was $65.2{\pm}0.9\%$ at the same depth. In the dose distribution according to the depth of water, the neutron dose decreased linearly and the gamma dose decreased exponentially as the depth was deepened. The factor expressed energy level, $D_{20}/D_{10}$, of the total dose was 0.718. Conclusion : Through the direct measurement using the two ion chambers, which is made different wall materials, and computer calculation of isodose distribution using MCNP simulation method, we have found the dose characteristics of low fluence fast neutron beams. If the power supply and the target material, which generate high voltage and current, will be developed and gamma contamination was reduced by lead or bismuth, we think, it may be possible to accelerator-based BNCT.

• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.36 no.4
• /
• pp.39-49
• /
• 2018

"Annals of The Joseon Dynasty" is a book recording the Joseon Dynasty's historical facts in an annalistic format. The King's amusement activities through "Annals of The Joseon Dynasty" which were established by the Ye-ak(禮樂) system were analyzed. The results are as follows. The king's amusement activities that were performed during the Joseon Dynasty period could be classified as state banquets, military banquets, and banquets for play. The analysis of the king's amusement activity was divided into five stages. The characteristic of [1 period : King Taejo~Sejo(Yejong)] was dominated the military banquets of the Goryeo Dynasty. Neo-Confucianism is the establishment of political and social turning of the ballast, considerations of military culture, culture, and Hoeryeyeon Jinpungjeong, a cloud of dust and elders banquets such as Giroyeon and Yangnoyeon on the nature of the party. A lasting ordinance was institutionalized[2 period : King Seongjong~Jungjong]. In the chopper and jeongyujaeran, Hong Kyung Rae led a royal amusement activities are stagnant, often produce isolated storage compute in the gloomy situation[3 period : King Injong~Hyeonjong]. Revival period is pride of the amusement activity through the culture of Joseon Dynasty royal culture [4 period : King Sukjong~Jeongjo]. The throne, crashed due to political power is an ebb of royal amusement activities, while also rapidly waning[5 period : King Seonjo~Seonjong]. During the early Joseon Dynasty, hunting took place around the forest area northeast of Hanyang and during King Seongjong's period, it took place closer to the capital city, while in Lord Yeonsan's period, it was expanded to a 39 kilometer radius area from the palace, and banquets such as various forms of entertainment of Cheoyongmu, and Flower-viewing. The Joseon kings who enjoyed hunting were King Sejong, Sejo, Seongjong, Yeonsan, and Jungjong. Most of hunting objects were tigers, bears, deer and roe deer, leopards, boars, their animals and falconry took, and the purpose of the hunting was to perform ancestral rites to the royal ancestry or the royal tombs. Lord Yeonsan's hunting activities had negative effects after King Jungjong the king's hunting activity decreased sharply. However, there were also positive aspects of Lord Yeonsan's Prohibition of cutting woods ect. In conclusion, the expansion of the King's garden(庭:courtyard${\rightarrow}$園:privacy garden${\rightarrow}$苑:king's garden${\rightarrow}$苑?:national hunting park) is evident which starts from formal and informal activities that took place in Oejo, Chijo, and Yeonjo, which went further to the separate and secret gardens, and then even further, thus setting the amusement activity area as a 39 kilometer radius range from Hanyang.

• Journal of Intelligence and Information Systems
• /
• v.27 no.3
• /
• pp.95-112
• /
• 2021

In university education, the choice of major class plays an important role in students' careers. However, in line with the changes in the industry, the fields of major subjects by department are diversifying and increasing in number in university education. As a result, students have difficulty to choose and take classes according to their career paths. In general, students choose classes based on experiences such as choices of peers or advice from seniors. This has the advantage of being able to take into account the general situation, but it does not reflect individual tendencies and considerations of existing courses, and has a problem that leads to information inequality that is shared only among specific students. In addition, as non-face-to-face classes have recently been conducted and exchanges between students have decreased, even experience-based decisions have not been made as well. Therefore, this study proposes a recommendation system model that can recommend college major classes suitable for individual characteristics based on data rather than experience. The recommendation system recommends information and content (music, movies, books, images, etc.) that a specific user may be interested in. It is already widely used in services where it is important to consider individual tendencies such as YouTube and Facebook, and you can experience it familiarly in providing personalized services in content services such as over-the-top media services (OTT). Classes are also a kind of content consumption in terms of selecting classes suitable for individuals from a set content list. However, unlike other content consumption, it is characterized by a large influence of selection results. For example, in the case of music and movies, it is usually consumed once and the time required to consume content is short. Therefore, the importance of each item is relatively low, and there is no deep concern in selecting. Major classes usually have a long consumption time because they have to be taken for one semester, and each item has a high importance and requires greater caution in choice because it affects many things such as career and graduation requirements depending on the composition of the selected classes. Depending on the unique characteristics of these major classes, the recommendation system in the education field supports decision-making that reflects individual characteristics that are meaningful and cannot be reflected in experience-based decision-making, even though it has a relatively small number of item ranges. This study aims to realize personalized education and enhance students' educational satisfaction by presenting a recommendation model for university major class. In the model study, class history data of undergraduate students at University from 2015 to 2017 were used, and students and their major names were used as metadata. The class history data is implicit feedback data that only indicates whether content is consumed, not reflecting preferences for classes. Therefore, when we derive embedding vectors that characterize students and classes, their expressive power is low. With these issues in mind, this study proposes a Net-NeuMF model that generates vectors of students, classes through network analysis and utilizes them as input values of the model. The model was based on the structure of NeuMF using one-hot vectors, a representative model using data with implicit feedback. The input vectors of the model are generated to represent the characteristic of students and classes through network analysis. To generate a vector representing a student, each student is set to a node and the edge is designed to connect with a weight if the two students take the same class. Similarly, to generate a vector representing the class, each class was set as a node, and the edge connected if any students had taken the classes in common. Thus, we utilize Node2Vec, a representation learning methodology that quantifies the characteristics of each node. For the evaluation of the model, we used four indicators that are mainly utilized by recommendation systems, and experiments were conducted on three different dimensions to analyze the impact of embedding dimensions on the model. The results show better performance on evaluation metrics regardless of dimension than when using one-hot vectors in existing NeuMF structures. Thus, this work contributes to a network of students (users) and classes (items) to increase expressiveness over existing one-hot embeddings, to match the characteristics of each structure that constitutes the model, and to show better performance on various kinds of evaluation metrics compared to existing methodologies.

• Journal of Intelligence and Information Systems
• /
• v.28 no.1
• /
• pp.175-196
• /
• 2022

Information and communication and home appliance industries, which were one of South Korea's main industries, are gradually losing their export share as their export competitiveness is weakening. This study objectively analyzed export competitiveness and suggested export-promising countries in order to help South Korea's information communication and home appliance industries improve exports. In this study, network properties, centrality, and structural hole analysis were performed during network analysis to evaluate export competitiveness. In order to select promising export countries, we proposed a new variable that can take into account the characteristics of an already established International Trade Network (ITN), that is, the Global Value Chain (GVC), in addition to the existing economic factors. The conditional log-odds for individual links derived from the Exponential Random Graph Model (ERGM) in the analysis of the cross-border trade network were assumed as a proxy variable that can indicate the export potential. In consideration of the possibility of ERGM linkage, a parametric approach and a non-parametric approach were used to recommend export-promising countries, respectively. In the parametric method, a regression analysis model was developed to predict the export value of the information and communication and home appliance industries in South Korea by additionally considering the link-specific characteristics of the network derived from the ERGM to the existing economic factors. Also, in the non-parametric approach, an abnormality detection algorithm based on the clustering method was used, and a promising export country was proposed as a method of finding outliers that deviate from two peers. According to the research results, the structural characteristic of the export network of the industry was a network with high transferability. Also, according to the centrality analysis result, South Korea's influence on exports was weak compared to its size, and the structural hole analysis result showed that export efficiency was weak. According to the model for recommending promising exporting countries proposed by this study, in parametric analysis, Iran, Ireland, North Macedonia, Angola, and Pakistan were promising exporting countries, and in nonparametric analysis, Qatar, Luxembourg, Ireland, North Macedonia and Pakistan were analyzed as promising exporting countries. There were differences in some countries in the two models. The results of this study revealed that the export competitiveness of South Korea's information and communication and home appliance industries in GVC was not high compared to the size of exports, and thus showed that exports could be further reduced. In addition, this study is meaningful in that it proposed a method to find promising export countries by considering GVC networks with other countries as a way to increase export competitiveness. This study showed that, from a policy point of view, the international trade network of the information communication and home appliance industries has an important mutual relationship, and although transferability is high, it may not be easily expanded to a three-party relationship. In addition, it was confirmed that South Korea's export competitiveness or status was lower than the export size ranking. This paper suggested that in order to improve the low out-degree centrality, it is necessary to increase exports to Italy or Poland, which had significantly higher in-degrees. In addition, we argued that in order to improve the centrality of out-closeness, it is necessary to increase exports to countries with particularly high in-closeness. In particular, it was analyzed that Morocco, UAE, Argentina, Russia, and Canada should pay attention as export countries. This study also provided practical implications for companies expecting to expand exports. The results of this study argue that companies expecting export expansion need to pay attention to countries with a relatively high potential for export expansion compared to the existing export volume by country. In particular, for companies that export daily necessities, countries that should pay attention to the population are presented, and for companies that export high-end or durable products, countries with high GDP, or purchasing power, relatively low exports are presented. Since the process and results of this study can be easily extended and applied to other industries, it is also expected to develop services that utilize the results of this study in the public sector.

• Asia Marketing Journal
• /
• v.12 no.4
• /
• pp.27-54
• /
• 2011

This research attempted to present the efficiency of culture marketing to the organizations producing culture-art products and to the companies utilizing art and suggest the practical viewpoints to the culture and art policy agencies. The methodology used was to take an in-depth look at the consumer value cognition and benefits of culture-art products in contemporary consumption culture from a social context by conducting a total of 12 Focus Group Interviews, consisting of 58 males and females in their 10s~50s who can represent culture-art product consumers. The culture-art products refer to the artist's spiritual, actual act of creating or to the end products with economic exchange value. They are also sense goods and merit goods that affect the mental state of consumers. By looking at culture-art products as consumer merit goods, this research examined consumer value cognition of culture-art products based on the characteristics culture-art products. As a result, this research determined that consumers view culture-art products largely as 'aesthetic and sensuous merit goods', 'actual and individual merit goods', and 'social public property'. As 'aesthetic and sensuous merit goods', culture-art products are considered as the products of an artist's creative activities; as 'social public property', culture-art products have a public value in terms of ownership; and as 'actual and individual merit goods', culture-art products act on the spirit and reality of a consumer in terms of consumption. As a result of analyzing the benefits of culture-art products based on the above-mentioned consumer value cognition, it was observed that the benefits of culture-art-product consumption are chiefly divided into 'aesthetic character-oriented', 'social relationships-oriented', and 'individual benefits-oriented' depending on how consumers see culture-art products. A 3-conceptional structures model was constructed according to the relationship between consumer value cognition of culture-art products and the benefits. This research revealed that consumers who pursue the aesthetic value or sense of beauty as the central reason experience culture-art products themselves, enjoy intellectual quests, and pursue their satisfaction by expressing affection for and interests in culture-art products. On the other hand, consumers who pursue social value as the central reason as a means of communication by perceiving culture-art products as a public property of society, pursue sympathy with people close to them through the symbolic power of culture-art product consumption or the joy of self-display. Consumers who perceive art products as spiritual and actual merit goods and pursue consumer value as a central reason want to express their own personality, develop themselves, and differentiate themselves or identify themselves with others in the context of social relations for the ultimate goal of living a happy and satisfied life while pursuing to satisfy imminent and actual necessities as emotional stability and rest. The fact that culture-art product benefits could vary according to how a consumer perceives them implies that consumer value cognition of culture-art products and their benefits significant affect consumers' decision in choosing and consuming various culture-art products. It turned out that such benefits from the consumption of culture-art products reflect the complex contemporary consumption culture of rational consumption, symbolic consumption, experiential consumption, and social reflective consumption. This research identified conceptional structures of consumer value cognition on culture-art products and benefits that can be used for studying and understanding culture-art products consumers who pursue a variety of consumption values. They can also be used by private companies in utilizing art, as well as by national agencies in enhancing the population's quality of life. However, since this research could only conceptually grasp consumer perception of culture-art products and reveal the dimension of classification due to its own limitations arising from characteristic investigation, quantitative data on the benefits of culture-art product consumers should be measured in future studies through a quantitative investigation, while using the value cognition of culture-art products and the individual characteristics of consumers as variables based on this research.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.25 no.1
• /
• pp.71-82
• /
• 2005

Khori(高麗) refers to the Chaabog(reindeer) that live on lichens(蘚) on Mt. Soyon(鮮) in which pastures are the cold and dry plateau of North Eurasia. Thus, the origin region of the Khori or Koguryo that are the ancestors of the reindeer-herding pastoral nomads(馴鹿 遊牧民) can be said to be the Steppe-Taiga-Tundra pastoral areas of North Eurasia and North America. When the pastoral nomads moved on to the great mountain(大山) zone of the Jangbaek(長白) to the Baekdu(白頭) Mountains, they could have been in contact with pastoral farmers or agricultural farmers living there and they became the farmers remaining on agricultural farms. They were the Koryo people, the ancestors of Korea. Staying in one place, they gradually forgot the origin of their reindeer-herding pastoral nomadic history in the Northwest area of Mt. Soyon, the small mountain(小山) zone of the Steppe-Taiga-Tundra pastoral areas. In other words, they lost their identity as reindeer-herding pastoral nomads when they entered the agricultural area after leaving the pastoral area. However, since their basic genes had already formed when they lived on the cold and dry plateau of North Eurasia, it is possible to study their pastoral nomadic history focusing on 'the minority living in the broad area(廣域少數)', by utilizing highly advanced biotechnological science and focusing on genes and information technology innovation, and removing various past hindrances in research. Therefore, it is not so difficult to restore the reindeerherding pastoral nomadic history of the Koguryo(高句麗) people and secure their pastoral nomadic identity, of which the first steps have already been taken into their historical stages. The Eurasian continent and the Korean peninsula, especially the cold and dry plateau of North Eurasia and the Korean peninsula have been closely related to each other ecologically and historically. They can never be a separate space at all. The Eurasian continent lies horizontally east to west and thus, the continent forms an isothermal zone. Also, since the time of producing their own foods, it was relatively easy for people with their technology to move to other places owing to the pastoral nomadic characteristic of mobility. Unlike the Chungyen(中原) region, western Asia and the regions covering the Siberia-Manchu-Korean peninsula where food production revolution was first made were connected to the Mongolian lichens route(蘚苔之路: Ni, ukinii jam) and steppe roads. Although the ecological conditions of nature have changed a bit throughout a long history, it was natural for the many tribes in North Asia living on the largest Steppe-Taiga-Tundra area in the world to have believed 'the legends related to animals in relation to their founders and ancestors(獸祖傳說)'. Assuming that Siberian tigers and the tigers living on Mt. Baekdu were connected ecologically and genetically because of the ecological characteristics of the animals, and their migration from plateau to plateau, we would suspect that the Chosun(朝鮮) tribe living on Mt. Baekdu were ethnically and culturally more closely connected to the farther removed Ural-Altai tribes that lived on the cold and dry plateau region than to the Han(i14;) tribe who lived in Chungyen(中原) that was close to Mt. Baekdu. More evidence is the structure of the Korean language which has the form of 'Subject + Object + Verb', which is assumed to have originated from the speedy lifestyle of the reindeer-herding pastoral nomads. The structure is quite different from that of the Han(漢) language, which is based on agricultural life. Also, it is natural for reindeer riding reindeerherding pastoral nomads or horse-riding sheep-herding pastoral nomads(騎馬, 羊遊牧民) to have held military and political power over the region and eventually to have established an ancient pastoral nomadic empire in the process of their conquest of agricultural regions. The stages for founding global empires in the history of mankind maybe largely divided into two, in terms of ecological conditions and occupations. They are the steppes and the oceans. Of course, the steppe-based empires were established based on the skills to deal with horses and the ability to shoot arrows while riding horses, along with the use of iron ware in the 8th century BC. The steppe-based empires became the foundation for an oceanic empire, which could have been established by the use of warships and warship guns since the 15th Century. Based on those facts, we know that Chosun, Puyo(夫餘), and Koguryo are the products of a developmental process of pastoral nomadic empires on the steppes. Maybe we can easily find the pastoral nomadic identity of the Koguryo more than we expected when we trace the origins and history of the Korean tribe living in the pastures located in the northwest area of Mt. Jangbaek by focusing on pastoral nomadic mobility and organization just as we have investigated the historic origins of Anglo-Saxons in America by focusing on the times before the 15th Century. In the process, we should keep in mind that English culture originated from the Industrial Revolution and was directly delivered to the American continent, although America was far from England and was not an intermediate point on long sojourns either. Further, American culture came back to England in a more advanced form later. The most important thing currently to be resolved is to cause Koreans to look back on their own history in a freer way of thinking and with diverse, profound, and sharp insight, taking away the old and existing conventional recognition that is entangled with complicated interests with Korean people and other countries. The meanings of Chosun, Khori, and Solongos have been interpreted arbitrarily without any historic evidence by the scholars who followed conventional tradition of fixed-minded aristocrats in an agricultural society. If the Siberian cultural properties of the stone age, the earthenware age, the bronze age, and the iron age are analyzed in such a way, archaeological discovery will never be able to contribute to the restoration of the Koguryo's pastoral nomadic identity. One should transcend the errors that tend to interpret the cultural properties discovered in the pastoral nomadic regions as not being differentiated from those of agricultural regions and just interpret them altogether from the agricultural point of view. A more careful intention is required in the interpretation of cultural properties of ancient Korean empires that seem to have been formed due to mutual interactions of pastoral nomadic and agricultural cultures. Also, it is required that the conventional recognition chain of 'reverse-genes' be severed, which has placed more weight on agricultural properties than pastoral nomadic ones, since their settlement on agricultural farms was made after the establishment of their ancient pastoral nomadic empires. There is no reason at all to place priority on stoneware, earthenware, bronze ware, and iron ware than on wooden ware(木器) and other ware which were made of animal skins(皮器), bones and horns(骨角器), in analyzing the history in the regions of reindeer or sheep pastures. Reading ancient Korean history from the perspective of pastoral nomadic history, one feels strongly the instinctive emotions to return to the natural 'mother place'. The reindeer-herding pastoral nomadic identity of the Koguryo people that has been accumulated in volumes in their genes and hidden deep inside and have interacted organically could be reborn with Burqanism(Burqan refers to 不咸 in Chinese), which was their religion by birth and symbolized as the red willow(紅柳=不咸). The mother place of the Koguryo's people is the endless vast green pastures of North Eurasia and North America, where we anticipated the development of Korean livestock farming following the inherent properties in the genes of the reindeer-herding pastoral nomads with Korean ancestors. We anticipate that the place would be the core resource that could contribute to the development of life of living creatures following the inherent properties of their genes and biotechnological factors. In other words, biotechnology used for a search for clues on the well-being of humans could be the fruit brought by Burqanism of the Koguryo people and the fruit of the globalization of Korean livestock farming. It is the Chosun farmer in China come from the vast nomadic reindeer pastures of North Eurasia that resolved the food problem of a billion Chinese people with lowland paddy rice seeds (水稻) by transforming Heilongjiang Province(黑龍江省) into an oceanic lowland paddy rice field(水田). Even Mao Tse-tung(毛擇東) could not resolve the food problem by his revolution campaigns for tens of years. Today is the very time that requires the development of special livestock farming following the inherent properties of the ancient Korean reindeer-herding pastoral nomads that respected the dignity of life on the cold and dry plateau of North Eurasia and the America continent. I suggest that research should be started from the pastures of the Dariganga Steppe in East Mongolia that was the homeland of Hanwoo(韓牛) and the central horse-herding steppe place(牧馬場) of Chingis Khan's Mongolia. The Dariganga Steppe is awash with an affluent natural environment for pastoral nomadic living however, the quality of life of the pastoral nomads there is still low. I suggest we Koreans, the descendents of the Koguryo, should take our first steps for our livestock farming business project and develop the Northern nomadic pastures, here at the pastures of the Dariganga Steppe, which is the Mongolian core place of state-of-the-art technology for military weapons.

• Sijohaknonchong
• /
• v.24
• /
• pp.5-46
• /
• 2006

Korean verse has flexibly changed its form and contents according to the historical background of the times. This fact arouses reader sympathy because it has reflected ideas, historical aspects and realities of the times. However, korean verse has kept its own characteristics in some ways, allowing it to exist today. It holds its form as 3 verses of three by three or four meter and three letters of the last of three verses. It makes every different version which has specific aspects of each times in the same 'sijo' area. 'Sijo' in Korean poems, is the first form that has been changed from formal to private functionally. As a result of that common verses in the Goryeo to Joseon eras were going with the stream of the times. Verse was the plate for justice so that there was no double meaning, symbols, or technical sentences. It had to show the idea of Myungchundo Jwonginryun. The theme was commonly fitted within certain areas. such as blessings, fidelity, devotion, etc. Around the end of the Joseon era, there was activation of private verses - a form of sijo with no restrictions on the length of the first two verses. Some ideas had been changed because Sarimpa gained power, domestic conflict, and the introduction of practical science. These things had an effect on the form of Sijo. After all, it shows the ideas of collapsing feudalism, resistance of confucian ideas, equality of the sexes, and opposition to the group who rule the government. Thus Sasul Sijo seems to have the tendency of resistance to reality. It was a specialty of realism poetry It explained our life in detail and reflected real life by being an intermediary of realism. This met and represented the demand of a reader's expectations. After 1905, there was new form of sijo that is very different, in form and content, from the previous versions. It was even different in areas of what people accepted. They started to think sijo was not the form of lyrical verse that is once was. It became a 'record of reading'. The form changed to 'hung or huhung' that satirized the times and the ending of a word in the last verse. Although this form could deliver the tension in statement, it was too iu from the original form. Therefore, it didn't last long, and its position got smaller because of the free verse that had western influence and was emerging in the times. In the middle of 1920, there was a movement of Sijo revival. It was lead by Choinamsun. He wrote poems and Sijo which were effected by western ideas in his early works. Although he worked with that, he took the lead in the movement of Sijo revival. He published the collection of Sijo $\ulcorner$Baekpalbunnwoi$\lrcorner$ that has one major theme-patriotic sentiment. He thought an ancient poem was a part of racial characteristics so that he expressed the main theme which represented the times and situations of his era. Modern Sijo is difficult. Sijo has to have modern and Korean verse characteristics at the same time. If it considers a modern aspect too much, it could not be distinguished from sijo and free verse. If it overly leans toward Sijo. it would seem to be too conservative which it then could be said to have no real charm of a poem. In spite of these problems, it is written constantly, because it has its own specialty. It has been focused on some works because they reflect awareness of modern times, the democratic idea, and realism. Overall, the authors of Modern Sijo express various themes by using different forms. The more what we can guess in this work, Sijo will exist permanently because of its flexibility. Furthermore, one special characteristic-flexibility of the korean verse will make it last forever and it will be a genre in Korean poetry.