• 드라이브 ㆍ 컨트롤
• /
• 제19권2호
• /
• pp.17-26
• /
• 2022

Recently, automatic transmissions caused a good improvement in the shift quality of a forklift. An advanced shift control algorithm, which was based on TCU firmware, was applied with embedded control technology and microcontrollers. In the clutch-to-clutch shifting, one friction element is released and the other friction element is activated. During this process, if the release and application timings are not synchronized, an overrun or tie-up occurs and ultimately leads to a shift shock. The TCU, which measures only the speed of the forklift, inevitably applies the open-loop shift control. In this situation, the speed ratio does not change during the clutch fill. The torque phase occurs until the clutch is disengaged. In this study, an offline shift logic of the learning control was proposed. It induced a synchronous shift when the learning control progressed. During this process, the reference current trajectory of the release clutch was corrected and applied to the next upshift. We considered the results of the overrun/tie-up characteristics of the upshift performed immediately before. The vehicle test proved that the deviation in shift quality, which was caused by the difference in the mechanical characteristics of the clutch, could be improved by the learning control.

• Journal of Power Electronics
• /
• 제15권6호
• /
• pp.1508-1516
• /
• 2015

A single phase H-bridge inverter is employed in conventional Inductive Power Transfer (IPT) systems as the primary side power supply. These systems may not be suitable for some high power applications, due to the constraints of the power electronic devices and the cost. A high-frequency cascaded multi-level inverter employed in IPT systems, which is suitable for high power applications, is presented in this paper. The Phase Shift Pulse Width Modulation (PS-PWM) method is proposed to realize power regulation and selective harmonic elimination. Explicit solutions against phase shift angle and pulse width are given according to the constraints of the selective harmonic elimination equation and the required voltage to avoid solving non-linear transcendental equations. The validity of the proposed control approach is verified by the experimental results obtained with a 2kW prototype system. This approach is expected to be useful for high power IPT applications, and the output power of each H-bridge unit is identical by the proposed approach.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 D
• /
• pp.2009-2010
• /
• 2006

This paper presents an adaptive line coupler to match input impedance of the Power line Communication(PLC) modem between access impedance of the power line. This line coupler provides maximum signal power transmiting capability, high reliability. The structure of this coupler is simple and designed to make a easy and low cost. The proposed line coupler is suitable for Amplitude Shift Keying(ASK) or Phase Shift Keying(PSK) modem. To figure out our models, the analysis of the transmitting features of power line channel is performed in the time domain at the carrier frequency. As a result of this study, we present the values of capacitors in the capacitor bank and adaptive line coupler circuit.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2008년도 춘계학술대회 논문집
• /
• pp.53-56
• /
• 2008

In this paper, we propose the battery charging device for electric bicycle using photovoltaic power. DC voltage from the solar cells is low, it needs to be step-up by the power conversion device. The power conversion device applied to this paper is phase-shift full-bridge converter. This converter steps-up from 12${\sim}$22[Vdc] to 36[Vdc] for charging the battery of electric bicycle. Phase-shift full-bridge converter(PSFB) can obtain twice as much DC voltage compared with half-bridge converter, thus it has lower current stress less than half-bridge converter. It is simulated and tested the battery charging device using photovoltaic power.

• 한국산업융합학회 논문집
• /
• 제4권3호
• /
• pp.305-310
• /
• 2001

Hydraulic power shifting systems of hydraulic travel motor may be far safer than mechanical power transmission systems. Thus, hydraulic power shifting systems are widely used for speed control on the hydraulic equipments. In the case of liquid shifting lines, the rapid change of area, such as valve closing, can result in a large pressure transient. It is necessary to assure proper control method in order to obtain the smallest shift shock. This study conducts the shock characteristics of hydraulic power shifting system of the hydraulic travel motor. Experimental results show that shock pressure depends on the operating pressure, flow rate and pipe line area. The shock characteristics can be applied for reducing shocks.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2011년도 추계학술대회
• /
• pp.389-391
• /
• 2011

본 논문에서는 VDR(VHF Data Radio)용 선형 25Watt 고출력 증폭기 회로를 설계하고 제작하여 특성을 측정하였다. VDR의 주파수 대역은 117.975~137MHz이고, CSMA(Carrier Sense Multiple Access) 다중 접속방식, D8PSK(Differential Eight Phase Shift Keyed), 25kHz 채널 대역폭을 사용한다. 또한 DO-281A MOPS에 규정된 출력 전력 및 심볼 배열 에러, 불요파 방사, 인접채널 전력을 만족해야 한다. 설계한 고출력증폭기는 DO-281A 표준을 만족한다.

• 예술인문사회 융합 멀티미디어 논문지
• /
• 제8권11호
• /
• pp.523-530
• /
• 2018

전력 변환 시스템의 고효율, 고전력 밀도를 위한 많은 연구가 활발하게 되어 왔다. 스위칭 주파수를 높임으로써 컨버터의 소형화 및 경량화를 꾀할 수 있으나 스위칭 주파수를 높이게 되면 스위칭 손실이 증가하게 된다. 따라서 스위칭 손실을 저감하기 위한 기법이 적용되어야 한다. 본 연구에서는 이 중 부가적인 회로 없이 변압기의 누설 인덕턴스와 스위치의 출력 커패시터를 이용하여 영전압 스위칭이 가능한 영전압 스위칭(Zero-Voltage Switching) 위상천이(Phase Shift) 풀 브리지 컨버터를 이용하여, 영전압 위상천이 풀 브리지 컨버터의 동작원리를 해석하고 2kW의 출력을 갖는 영전압 스위칭 풀 브리지 컨버터를 설계한다. 각 모드별 동작을 스위치 도통 상태와 전압 전류 파형으로 분석하였다. 분석 결과, 영전압 스위칭이 도통 스위치들의 각 쌍 사이의 위상 변화에 의해 최대 효율을 달성하는 것을 확인하였다. 제안된 영전압 위상천이 풀 브리지 컨버터 설계를 검증하기 위해 컴퓨터 시뮬레이션 툴인 PowerSIM사의 PSIM을 이용하여 설계된 2kW 출력 전력을 갖는 영전압 스위칭 위상천이 풀 브리지 컨버터의 성능을 확인하였고, 실험을 통해 연구의 타당성을 입증하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.674-679
• /
• 2002

As the object of this study, a transmission system with the style of HST in combination with mechanical semi-automatic transmission for application in hydraulic wheel excavators was chosen. The dynamic characteristics of the object transmission was studied by numerical analysis of the mathematical model. The results of numerical analysis showed comparatively good agreements with experimental results, so the validity of the numerical analysis process was ascertained.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2000년도 전력전자학술대회 논문집
• /
• pp.270-273
• /
• 2000

A new phase shift PWM parallel-input/series-output modularized dual converter is proposed in this paper. This converter is operated with a fixed duty ratio and its output voltage is regulated by phase shift between each module. Since the operating duty ratio of each module is fixed it is sufficient to implement a simple open loop drive circuitry for each module and the cost of total system can be much reduced. The operation of the converter is analyzed in this paper and verified by computer simulation.

• Journal of Power Electronics
• /
• 제15권5호
• /
• pp.1158-1167
• /
• 2015

In this paper, a new hybrid DC-DC converter is proposed for electric vehicle 3.3 kW on-board battery charger applications, which can be modulated in a phase-shift manner under a fixed frequency or frequency variation. By integrating a half-bridge (HB) LLC series resonant converter (SRC) into the conventional phase-shift full-bridge (PSFB) converter with a full-bridge rectifier, the proposed converter has many advantages such as a full soft-switching range without duty-cycle loss, zero-current-switching operation of the rectifier diodes, minimized circulating current, reduced filter inductor size, and better utilization of transformers than other hybrid dc-dc converters. The feasibility of the proposed converter has been verified by experimental results under an output voltage range of 250-420V dc at 3.3 kW.