• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.17 no.1
• /
• pp.8-17
• /
• 2021

The seat leakage test is required after the maintenance work on the valve seat. Either the test has been performed outside of the plant after cutting the valve from the pipe system or the simplified test has been performed so far. It was unable to perform the test at the plant site because it is hard to make a steady pressure on the valve inlet when it is installed in the pipe. This research aims to perform the leakage test in the nuclear power plant while it is installed in the pipe system. The mock-up test is performed by pressurizing the leak-off pipe on the valve body. The result is compared with traditional test result by pressurizing the valve inlet. Furthermore the chamber mock-up tests are performed under various conditions. The leak rate by the developed test using the leak-off pipe is found to be similar but greater than the leak rate by the existing test method. It implies that the test using the leak-off pipe is more conservative than the existing test. The methodology and the equipment which this paper suggests that on-site seat test is possible and the application of the technology could reduce the time and cost for the valve maintenance work significantly.

• Journal of Power System Engineering
• /
• v.15 no.5
• /
• pp.67-71
• /
• 2011

Fine blanking is a specialized form of blanking where there is no fracture zone when shearing. This is achieved by compressing the whole part and then an upper and lower punch extract the blank. This allows the process to hold very tight tolerances, and perhaps eliminate secondary operations. In the present study, tensile test and numerical simulation has been performed to investigate distribution of deformation and stress of car seat recliner. The commercial ABAQUS/Explicit software was applied for analyzing the stress and strain of the recliner. In analysis, three lock gear has reached the maximum moment on rotational degree of 2.27. This is more than two times than maximum moment of same size recliner, and can be used safely. Therefore, these can use as criterion of actual structural design.

• Journal of Power System Engineering
• /
• v.17 no.1
• /
• pp.42-49
• /
• 2013

The global movie industry is continuing rapid growth through application of the latest technology. 3D movies are being produced and shown for a more effective viewing experience. Special chairs for audiences are being experimentally manufactured and installed for the greatest viewing effect. This special chair has a structure that applies vibrating stimuli to specific parts of the body by attaching vibration transducers to theater chairs and synchronizing it with each scene of the movie. In a previous study, it has been confirmed that we can analyze the vibration transfer characteristics of sponge seats through the application of an experimental modal analysis method and obtain design variables easily. In this paper, we examine the major design parameters needed in the development of a foaming sponge seat in which auxiliary springs are inserted to improve the vibration transfer effect of a chair seat. Through analyzing several prototypes by applying experimentation as well as the experimental modal analysis method, it was confirmed that the effect of vibration transfer can be improved through the use of an auxiliary member.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.1
• /
• pp.101-107
• /
• 2018

In this study, the analysis of radiation noise and chattering noise of vehicle seat recliner was conducted through testing and analysis. First, operating noise was measured by seat back frame and recliner, and chattering noise was confirmed. Next, the transient dynamic analysis was performed, and the result was mapped to the acoustic analysis. Finally, the test and analysis were compared and analyzed. The results are as follow. First, it was found that the peaks appeared in common in the range of 620~650Hz, 1,240~1,290 Hz, and 1,840~1,940 Hz. It was judged that the dynamic characteristics of the recliner system overlapped with the rotation component of the motor to cause amplification of noise and vibration. Next, as a result of imaging the radiation noise analysis, it was judged that the noise radiated in the forward and backward direction has a greater influence than the direction of the rotation axis when the ear position of the person is taken as a reference.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.6
• /
• pp.15-20
• /
• 2017

This study analyzed the load change of the gear generated by the operation of the vehicle recliner through Finite Element Analysis. The basic model of the recliner used was a commercial product, and the effect of the seat frame was excluded. The load conditions applied to the recliner were set considering gravity, the mass of the seat's back frame, and the weight of a person. The operating mode was set to move the seat back from the vertical to the reclined position. As a result, it was found that the tooth bending amount of the gear rim and wheel increased from the cam rotation angle of 450 degrees, and a change in the contact ratio occurred. Furthermore, excessive torque fluctuations occurred in the ranges of 390 to 450 and 750 to 710 degrees. It was found that this occurred in the region of about 30 degrees before and after the point where the x-axis direction load is larger than the y-direction load. From this torque fluctuation it was determined to likely to cause chattering noise.

• Journal of Power System Engineering
• /
• v.7 no.3
• /
• pp.23-28
• /
• 2003

In heavy nuclear power plant, high energy through main steam line is provided to turbine that generate the electric power. Since plant had generated power, high noise has been occurred. Noise make equipments and work environment worse. For finding out the location and the cause of making noise, noise was measured along main steam line at open/close test of Main Steam Isolation Valve (MSIV hereafter). As the result, it was identified that the vortex shedding in the cavity of MSIV is main noise source. The profile change of MSIV seat ring was proposed as the method of noise reduction. After filletting MSIV seat ring, the noise level reduced $10{\sim}20dB$ compared before the change of profile.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.28 no.4
• /
• pp.315-322
• /
• 2008

Valves in power plants are leaking internally by various damages including insertion of foreign objects on seat, seat crack, defects and fatigue crack of stem packing or welds etc. due to severe operating conditions such as high temperature and high pressure for extended period time. Acoustic emission(AE) technology should be applied in order to diagnose precisely and evaluate these valve internal leak. In this paper, results of studies which have accomplished in actual power plant are presented. We have analyzed background noise, AE signal level and frequency spectrum through laboratory tests on the basis of various actual conditions in power plant, and also have considered evaluation methods on the background noise, AE properties and the detectable minimum leak rate according to valve leak conditions through comparing with results of field tests in power plant. As a result of these studies, we conformed that evaluation of internal leak conditions including discrimination of leak or not, and the detectable minimum leak rate is possible, and also it is expected to contribute to safe operation and prevention of energy loss in power plants.

• Journal of Industrial Technology
• /
• v.26 no.A
• /
• pp.47-54
• /
• 2006

To improve passenger safety, seat belt systems with pre-tensioner that tightens seat belt webbing using explosive just before collision are widely used these days. Even though seatbelt must not unlatched without passengers' operation. explosive power of pre-tensioner can cause unlocking of a buckle. To prevent the unlocking, an anti-g mass that blocks displacement of the release button has been attached to the buckle. In this study, the dynamics and statics of locking mechanism associated with operation of anti-g buckle has been theoretically investigated, and important design variables that affect the operation of anti-g buckle have been identified. Through the total seat belt system's dynamic simulation using force and displacement inputs obtained from seat belt sled test, design of the proposed anti-g buckle has been validated.

• The Journal of the Acoustical Society of Korea
• /
• v.37 no.4
• /
• pp.248-255
• /
• 2018

It is known that the road noise on the rear seat of a hatchback type car is worse than that of a sedan type car because of the weakness on sealing structure. Therefore, a sound sealing system and sufficient absorption/insulation performance are required. In the case of a compact segment car, however, the application of the sufficient absorption and insulation materials is limited, because of the restriction on the production cost and weight of the car. In this study, we estimate the noise transmission path on the vehicle's body structure from tires and ground using the PBNR (Power Based Noise Reduction) method which is useful in quantitative measurement. Based on these results, we suggest an alternative absorption/insulation method for the better performance of rear seat road noise reduction in a compact hatchback car.

• Journal of Biosystems Engineering
• /
• v.22 no.1
• /
• pp.41-48
• /
• 1997

A nondestructive quality inspection technique using acoustic impulse response method was studied to investigate the feasibility of egg shell inspection. An experimental system was built to generate impact force, to measure the response signal and to analyze the frequency spectrum. This system includes an impulse generating unit, an egg holding seat, a microphone with preamplifier, and a digital oscilloscope connected to Personal Computer by RS-232C interface. The factors such as impulse generating method, egg holding method, and sensor location were evaluated by analyzing the power spectrum density of the measured signal. The results obtained are summarized as follows : 1. From the sampled eggs, the proper conditions for detecting damaged eggs were found as followings; ceramic for the impact ball material, rubber for egg seat material, 20 degrees for an impact angle of pendulum, 10mm for the distance between egg and sensor, the sharp side for impacting part, and 180 degrees for the location of sensor. 2. Examination of the Fourier transformed analysis in beth normal and damaged eggs revealed that those factors such as the resonant frequency, a number of peak frequencies and the magnitude of power spectrum were important to detect damaged eggs.