• 전기학회논문지
• /
• 제56권7호
• /
• pp.1250-1254
• /
• 2007

The multi-resonant(MR) converter has a characteristics that the parasitic components existing in the converter are absorbed into the resonant circuits. The designed MR converter could be got a high efficiency and a high power density because the switching power losses are reduced effectively due to resonant switching circuit. However, the high resonant voltage stress of switching power devices leads to the conduction loss. In this paper, it is proposed the novel alternated(AT) flyback multi-resonant converter to overcome such a drawback. The suggested converter dc input is divided by two series input filter capacitors. The resonant stress voltage is reduced to 2-3 times the input voltage without any complexity and it provides the various circuit schemes in lots of applications. The proposed flyback MR converter is verified through simulation and experiment.

• 조명전기설비학회논문지
• /
• 제28권8호
• /
• pp.82-89
• /
• 2014

The industrial products to use single phase inverter are raised the necessity of power quality improvement, such as AC Motor Driver, Lighting, Renewable energy power converter. Also, it is increasing that applied the single phase multilevel inverter for high quality power at renewable energy power converter. Especially, the photovoltaic multilevel inverters have at least more than two DC_Link and more than one DC/DC Converter. This paper proposes a triple output DC/DC Converter with one switch for photovoltaic multilevel inverter. The proposed converter has advantages of low cost and volume because it has one switch. The operation principle of the converter is analyzed and verified. A prototype is implemented to verify of the proposed converter.

• Journal of Electrical Engineering and Technology
• /
• 제5권3호
• /
• pp.477-483
• /
• 2010

This paper is studied on a novel buck-boost isolated converter for high efficiency and high power factor. The switching devices in the proposed converter are operated by soft switching technique using a new quasi-resonant circuit, and are driven with discontinuous conduction mode (DCM) according to pulse width modulation (PWM). The quasi-resonant circuit makes use of a step up-down inductor and a loss-less snubber capacitor. The proposed converter with DCM also simplifies the requirement of control circuit and reduces a number of control components. The input ac current waveform in the proposed converter becomes a quasi sinusoidal waveform in proportion to the magnitude of input ac voltage under constant switching frequency. As a result, it is obtained by the proposed converter that the switching power losses are low, the efficiency of the converter is high, and the input power factor is nearly unity. The validity of analytical results is confirmed by some simulation results on computer and experimental results.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.112-115
• /
• 2002

Previous AC/DC PFC Boost Converter perceives feed forward signal of input and feedback signal of output for average current-mode control. Previous Boost Converter, the quantity of input current will be decreased by the decrease of output current in light load, and also power factor comes to be decreased. Also the efficiency of converter will be decreased by the decrease of power factor. The proposed converter presents the good PFC(Power Factor Correction), low line current hormonic distortions and tight output voltage regulations using non-dissipative snubber. The proposed converter also has a high efficiency by non-dissipative snubber circuit. To show the superiority of this converter is verified through the experiment with a 640W, 100kHz prototype converter.

• 전력전자학회논문지
• /
• 제17권1호
• /
• pp.48-56
• /
• 2012

This paper deals with power electronic converter education program using LabVIEW. LabVIEW is a graphic based programming language with easy debugging, which is suitable for education program that can be used to study and figure out the operation of power electronic converters. When LabVIEW is employed as a simulation program of the operation of power electronic converters, the resulting program has the advantage such that the effects of the change of control variables and circuit parameters on the various variables such as the output voltage and the inductor current etc can be directly displayed without any separate compiling procedure. This paper shows the design procedure and the characteristics of the power electronics education program implemented by LabVIEW focusing on DC-DC converter among power electronic converters.

• Journal of Power Electronics
• /
• 제8권1호
• /
• pp.60-73
• /
• 2008

In this paper a three-phase ac-to-dc resonant converter with high input power factor and isolated output is proposed. To improve the input power factor of the converter, high frequency current is injected into the input of the three-phase diode bridge rectifier. It is injected through an impedance network consisting of a series of L-C branches from the output of the high frequency three-phase inverter. A narrow switching frequency variation is required to regulate the output voltage. A design example with different design curves is illustrated along with the component ratings. Experimental verification of the converter is performed on a prototype of 3 kW, 1000 V output, operating above 300 kHz. Experimental results confirm the concept of the proposed converter. Narrow switching frequency variation is required to regulate the output voltage.

• 전기학회논문지
• /
• 제56권2호
• /
• pp.301-310
• /
• 2007

Bidirectional DC-DC converters allow transfer of power between two dc sources, in either direction. Due to their ability to reverse the direction of flow of power, Dey are being increasingly used in many applications such as battery charge/dischargers, do uninterruptible power supplies, electrical vehicle motor drives, aerospace power systems, telecom power supplies, etc. This Paper Proposes a new bidirectional Sepic/Zeta converter. It has low switching loss and low conduction loss due to auxiliary communicated circuit and synchronous rectifier operation, respectively Because of positive and buck/boost-like DC voltage transfer function(M=D/1-D), the proposed converter is very desirable for use in distributed power system. The proposed converter also has both transformer-less version and transformer one.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2003년도 추계학술대회 논문집
• /
• pp.90-94
• /
• 2003

Recently, many nations have released standard such as IEC 1000-3-2 and IEEE 519 which impose a limit on the harmonic current drawn by equipment connected to AC line in order to prevent the distortion of an AC line. Among the wide variety of active methods for improving power factor and harmonic distortion, the boost converter is very effective because it has a continuous line current , small choke filter and high power factor. In high power application, however, the bridge diode loss in the boost converter has made the efficiency lower and the temperature of the board higher. A new approach without bridge diode to make the same characteristics of the conventional boost converter has also been developed. This paper present the comparisons between the continuous current mode(CCM) operated conventional boost converter and the boundary current mode(BCM) operated the bridgeless boost converter for high efficiency and high power factor.

• 전기학회논문지P
• /
• 제61권4호
• /
• pp.161-167
• /
• 2012

Energy conversion systems such as power inverters and converters are basically significant in establishing photovoltaic power systems to enhance power effectiveness. This paper proposes a new converter control method by using the Lyapunov redesign approach. We construct the proposed control mechanism linearly composed of nominal control and auxiliary control laws. The former is generally designed through a well-known power electronic technology and the latter is implemented to compensate real-time control error due to uncertain natures of converter systems in practice. For realizing adaptive control capability in the proposed control mechanism, a control parameter vector is estimated by utilizing a steepest descent based optimization method. We carry out numerical simulation with Matlab(c) software to demonstrate reliability of the proposed converter control system and conduct a comparative study to prove its superiority by comparing with a generic converter control methodology.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제52권9호
• /
• pp.468-474
• /
• 2003

This paper describes the development of an open frame type high power density switching converter. It is based on the active clamp forward converter with synchronous rectifier, and packaged by using the open frame and multi-layer printed circuit board (PCB) technology to achieve the higher power density. Furthermore, the windings of transformer and inductor are also realized by multi-layer PCB so that it also contributes to achieve higher power density. Through the experiment on the prototype converter of 50[W], it is confirmed that power density of 50[W/i$n_3$] and maximum efficiency of over 91[%] are obtained.