• Cement Symposium
• /
• s.49
• /
• pp.29-30
• /
• 2022

Since the climate problem getting severe, carbon neutrality is rising global issue. The limestone powder addition that can substitute clinker in cement is look forward to get positive effect as filler. This study focus on the effect of limestone powder chemical characteristic on mortar workability and compressive strength. Consequently, regardless of type of limestone and subsitution amount, the compressive strength was lower then OPC. But the workability of limestone composite cement showed higher then OPC. Considering latter strength development, using unit water decreasing effect of limestone composite cement is planned further.

• Journal of the East Asian Society of Dietary Life
• /
• v.16 no.6
• /
• pp.747-752
• /
• 2006

This study developed gasiogapidduk to increase the functional value and flavor of traditional Baiksulgi by adding gasiogapi powder. Powdered nonglutinous rice was mixed with powdered leaves (1%, 2%, 3%), powdered stems roots (1%, 3%, 5%), and powdered freeze-dried root extracts (5%, 10%, 15%) of Acanthopanax senticosus, known as the second ginseng, in order to find the combination ratio optimal to the senses. Sensory evaluation and texture characteristic evaluation of gasiogapidduk were used to develop a functional rice cake appealing to the largest number of people. Sensory evaluation consisted of evaluating color, smell, taste and texture, preference quality which reflects overall appeal. Texture characteristics were evalauated on hardness, adhesiveness, cohesiveness, springiness and gumminess. As a result, AE5 mixed with 5% powdered freeze-dried Acanthopanax senticosus extract proved to be the most desirable in both sensory evaluation and texture characteristics.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.5
• /
• pp.1115-1122
• /
• 1993

Several yield criteria for porous materials are compared with each other, defining the apparent yield stress as the yield stress of the porous material in simple compression. It was found that the plastic Poisson's ratio is the parameter needed to define the yield criterion, rather than the relative density. The plastic Poisson's ratio is regarded as a material characteristic that is obtained from a simple compression test. A new form of yield criterion was suggested, and it was applied to hydrostatic compression as well as uniaxial strain compression of sintered Al-2024 powder. The crossover point in the mean stress vs volume change curves of the processes was predicted. It is presented that the flow stress of the fully densed material can be obtained from that of the porous material using relations obtained from the yield criterion.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.6
• /
• pp.399-406
• /
• 2014

Thermal batteries are used for military power sources that require robustness and long storage life such as missiles and torpedoes. $FeS_2$ powder is currently used for cathode materials because of its high specific energy density, environmental non-toxicity and low cost. However, large particle size of conventional $FeS_2$ has been deterred its possible application for higher power thermal batteries. In order to improve the power density, high energy ball milling of $FeS_2$ has been introduced to crush the micron-sized $FeS_2$. Discharge characteristics of the single cells fabricated with nano-materials and conventional $FeS_2$ powder were evaluated.

• KIEAE Journal
• /
• v.6 no.1
• /
• pp.11-16
• /
• 2006

This paper deals with the experimental for manufacturing the lightweight buildng materials with portland cement, fly ash, slag, lime, gypsum, and aluminum powder system. Aluminum powder was added an aerating agent. Specific gravity range of lightweight concrete specimens were 0.6~0.9g/cm3. These specimens properties studied by means of specific gravity, compressive strength, absorption coefficient, transmission loss and scanning electron microscopy. Cellular concrete with maximum compressive strength was 41kgf/cm2 by obtained Al=0.05wt.%. Moreover, the aeration lightweight concrete showed excellent sound absorption properties.

• Journal of the Korean Ceramic Society
• /
• v.31 no.11
• /
• pp.1378-1386
• /
• 1994

The characteristic of calcined BaTiO3 powder and sintered PTC ceramics was investigated varing with calcination temperature and time of BaTiO(C2O4)2.4H2O synthesized from BaCl2.2H2O, TiCl4, oxalic acid and ethanol by oxalic acid method. When the particle size was less than 0.1 ${\mu}{\textrm}{m}$ by controlling calcination temperature and time, the resistance at room temperature was measured very high (above M{{{{ OMEGA }}). However, when the calcined particle sizes ranged from 0.2 to 0.3 ${\mu}{\textrm}{m}$, the resistance was 100 {{{{ OMEGA }} (After sintering, the grain size was 10~30 ${\mu}{\textrm}{m}$ homogeneously with the addition of dopant in sintering, the resistivity, resistance, $\alpha$ value and jumped to were 110{{{{ OMEGA }}.cm, 24$^{\circ}C$/% and 106{{{{ OMEGA }}, respectively.

• Journal of Powder Materials
• /
• v.13 no.6 s.59
• /
• pp.450-454
• /
• 2006

Wear of steel plate was measured during unlubricated sliding against TiC composites. These composites consist of round TiC grains and steel matrix. TiC grain itself exhibits low surface roughness and round shape, which does not bring its counterpart into severe damage from friction. In our work a classical experimental design was applied to find out a dominant factor in counterpart wear. The analysis of the data showed that only the applied load has a significant effect on the counterpart wear. Wear rate of counterpart increased non-linearly with applied load. Amount of wear was discrepant from expectation of being in proportion to the load by analogy with friction force. Our experimental result from treating matrix variously revealed bimodal wear behavior between the composites and counterpart where a mode seems to result from the special lubricant characteristic of TiC grains, and the other is caused by metal-to-metal contact. The two wear mechanisms were discussed.

• Transactions of Materials Processing
• /
• v.20 no.8
• /
• pp.575-580
• /
• 2011

Direct laser melting(DLM) is promising as a joining method for producing parts for automobiles, aerospace, marine and medical applications. An advantageous characteristic of DLM is that it affects the parent metal very little. The mechanical properties of parts made by DLM are strongly affected by the porosity and surface roughness of the laser melted beads. This is a systematic study of the effects of the porosity and surface roughness of laser melted beads using various processing parameters, such as laser power, scan rate and overlapping ratio of the fill spacing. The specimens were fabricated with 316L and 304L austenitic stainless steel powder. Dense parts with low porosity were obtained at low laser scan speed, as it increased the aspect ratio of the parental material and the depth of penetration. The variations of surface roughness were examined at various processing parameters such as overlapping ratio and laser power.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.927-929
• /
• 2014

MRE(Magneto-rheological Elastomer) is a material which shows reversible and various modulus in magnetic field. Comparing to conventional rubber vibration isolator, MREs are able to absorb broader frequency range of vibration. These characteristic phenomena result from the orientation of magnetic particle (i.e., chain-like formation). Magnetic reactive powder(MRP), having rapid magnetic reaction, was selected as a magnetic particle to give magnetic field reactive modulus. The mechanical properties of manufactured MREs were measured with the application of magnetic field. The analysis of MR effect was carried out by FFT analyzer with various induced current. As induced magnetic field intensity increased and coated with MRP, increment of MR effect was observed.

• Journal of Powder Materials
• /
• v.8 no.3
• /
• pp.186-191
• /
• 2001

Several fabrication processes, corresponding nanostructural features and multifunctionality as well has been investigated for oxide ceramic based nanocomposites with metal nanodispersion (i.e., ceramic/metal nanocomposites). Transition metal (Ni, Co, etc) dispersed alumina and zirconia based nanocomposites have been synthesized by reducing and hot-press sintering of ceramic and metal oxide mixtures prepared by several method. Improved fracture strength (1.1 and 1.9 GPa for $Al_2O_3/Ni$ and $ZrO_2/Ni$ nanocomposites, respectively) of these composites have been achieved according to their nanostructures. In addition, ferromagnetic characteristic has been kept. The variation of magnetization with an applied stress has found to be more sensitive as smaller as the magnetic metal dispersion is. This result thus suggests the possibility of fracture and/or stress sensing of the composites by simple magnetic measurement.