• Journal of the Korean Home Economics Association
• /
• v.36 no.2
• /
• pp.145-160
• /
• 1998

This study was designed to investigate purchasing and post-purchase behaviors of middle-aged wives in buying townwears, an well as to examine socio-demographic variables, physical variables, psychological variables, and their influences on. The data included 374 housewives in Seoul and Pusan. Statistics used for data analysis were Frequencies, Means, Standard Deviation, t-test, ANOVA, Pearson's Correlation. The major finding are as follows: 1. The level of post-purchase satisfaction marked higher than middle point. 2. Post-purchase satisfaction differed significantly in income, health-state, identity, stress perceptivity, income satisfaction, sense of comparison, and propensity to consume.

• Computers and Concrete
• /
• v.15 no.2
• /
• pp.199-213
• /
• 2015

The residual fracture toughness of post-fire normal-strength concrete subjected up to $600^{\circ}C$ is considered by the wedge splitting test. The initial fracture toughness $K_I^{ini}$ and the critical fracture toughness $K_I^{un}$ could be calculated experimentally. Their difference is donated as the cohesive fracture toughness $K_I^c$ which is caused by the distribution of cohesive stress on the fracture process zone. A comparative study on determining the residual fracture toughness associated with three bi-linear functions of the cohesive stress distribution, i.e. Peterson's softening curve, CEB-FIP Model 1990 softening curve and Xu's softening curve, using an analytical method is presented. It shows that different softening curves have no significant influence on the fracture toughness. Meanwhile, comparisons between the experimental and the analytical calculated critical fracture toughness values further prove the validation of the double-K fracture model to the post-fire concrete specimens.

• Journal of the Semiconductor & Display Technology
• /
• v.15 no.4
• /
• pp.73-78
• /
• 2016

Contact pressure distribution between PVA brush and semiconductor wafer was measured by developing a test setup which could simulates the post CMP cleaning process. The test set-up used thin film type pressure sensor which could measure the pressure distribution of contact area with the resolution of $15.5ea/cm^2$. As the experimental results, it was verified that there had been severe contact pressure non-uniformity along the axis of the brush and between the adjacent projections on the brush's surface. These results should be considered when developing post CMP cleaning stage or designing the PVA brush.

• Transactions of Materials Processing
• /
• v.12 no.6
• /
• pp.542-549
• /
• 2003

Three-dimensional forging analysis becomes an inevitable tool to make design process more reliable and more producible. In this study, in order to make the investigation for three-dimensional forging analysis more conveniently and accurately, a new post processor was developed. For post-processing of multi-stage forging simulation, efficient data structure was proposed and applied by using STL. New file architecture was developed to handle successive and huge data efficiently, common in three-dimensional forging analysis. Since sectioning and flow tracing plays an important role in the investigation of analysis result, we developed an algorithm suitable for 4-node and 10-node tetrahedron. This flow tracing algorithm can trace and reverse-trace flow through remeshing. Developed program shows good performance and functionality. Especially, a big size problem can be handled easily due to proposed data structure and file architecture.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2022.05a
• /
• pp.176-178
• /
• 2022

대규모 양자컴퓨터의 개발은 현재 사용하는 많은 암호화 알고리즘에 위협이 될 것으로 예상한다. 현재 NIST 는 양자 후 시대에 대비하기 위해 양자 내성 암호를 표준화 하기 위한 작업을 진행하고 있으며 이에 따라 post-quantum 시스템의 마이그레이션 과정이 필요하며 각 시스템에 QSC 적용을 위한 연구들이 이어지고 있다. 본 논문에서는 양자 후 시대에 대비하기 위해 NIST 의 PQC post quantum conference 에서 발표한 PQC 후보와 QSC 마이그레이션 과정 및 적용 방안에 대해 조사한다.

• 도로교통
• /
• s.93
• /
• pp.6-13
• /
• 2003

• Journal of the Microelectronics and Packaging Society
• /
• v.14 no.4
• /
• pp.43-48
• /
• 2007

This study is focused on the effect of the surface properties for the post electrode, which is used in pad formation consisted of SMT such as IC, passive component, combined with fired LTCC substrate, We carried out the surface microstructure of sintered electrode and the basic reliability evaluations with sample fired by microwave sintering to solve the problems occurred in post electrode by electric sintering. We evaluated surface densification status of post electrode according to various conditions of microwave sintering. In additions, it is obtained strong effect on blister improvement of post electrode because of over-sintering and the insufficient out gas in bum out process. As a result of adhesion strength, we confirmed $44.3N/mm^2$ in microwave sintering and $34.5N/mm^2$ in electric sintering, respectively. This result will be used for the basic reliability test. Finally, microwave sintering seems to be economic in process time with 30 min compared to electric sintering with 10 hr. In terms of Mass production and efficiency, microwave sintering are excepted to be higher than electric sintering.

• Korean Journal of Metals and Materials
• /
• v.50 no.4
• /
• pp.316-323
• /
• 2012

The aim of this study is to investigate the effect of post heat treatment on bonding properties of roll cladded Ti/MS/Ti materials. First grade Ti sheets and SPCC mild steel sheets were prepared and then Ti/MS/Ti clad materials were fabricated by a cold rolling and post heat treatment process. Microstructure and point analysis of the Ti/MS interfaces were performed using the SEM and EDX Analyser. Diffusion bonding was observed at the interfaces of Ti/MS. The thickness of the diffusion layer increased with post heat treatment temperature and the diffusion layer was verified as having $({\epsilon}+{\zeta})+({\zeta}+{\beta}-Ti)$ intermetallic compounds at $700^{\circ}C$ and an $({\zeta}+{\beta}-Ti)$ intermetallic compound at $800^{\circ}C$, respectively. The micro Knoop hardness of mild steel decreased with post heat treatment temperature; however, those of Ti decreased at a range of $500{\sim}600^{\circ}C$ and showed a uniform value until $800^{\circ}C$ and then increased rapidly up to $900^{\circ}C$. The micro Knoop hardness value of the diffusion layer increased up to $700^{\circ}C$ and then saturated with post heat treatment. A T-type peel test was used to estimate the bonding forces of Ti/Mild steel interfaces. The bonding forces decreased up to $800^{\circ}C$ and then increased slightly with post heat treatment. The optimized temperature ranges for post heat treatment were $500{\sim}600^{\circ}C$ to obtain the proper formability for an additional plastic deformation process.

• Asian-Australasian Journal of Animal Sciences
• /
• v.22 no.5
• /
• pp.686-693
• /
• 2009

A 21- to 42-day feeding study was conducted in Ross male broilers to evaluate the use of dried bakery product (DBP) and the influence of adding fat at different points in the manufacturing process. Six dietary treatments were formulated using a factorial arrangement (3${\times}$2 design) with three levels of fat in the mixer (high: 4.8%, medium: 3.8% and low: 2.8%) with or without DBP (0 and 7%). Additional fat was sprayed on pellets in a post-pelleting liquid application to bring the fat content to a similar level in all diets. Data on pellet quality (before and after post-pelleting fat addition), broiler performance, nutrient digestibility and organ weights were studied. Pellets made with DBP showed higher hardness values when measured before post-pelleting fat addition (p<0.001), although DBP did not affect final pellet hardness or durability. Higher post-pelleting hardness and durability were shown by diets to which a lower level of fat had been added in the mixer (p<0.001). In general, post-pelleting fat application improved durability (p<0.05). However, broiler performance and ileal digestibility were not affected by any of the factors tested. Dietary treatments had a significant but variable effect on carcass yield (p<0.01), although there were no differences among treatments regarding breast and leg yield, abdominal fat or organ weights. The results indicate that up to 7% DBP could be used in the broiler diet without impairing performance, ileal digestibility or organ weights. The place or point of fat addition in the manufacturing process has a strong influence on pellet quality.

• Journal of the Korean Ceramic Society
• /
• v.42 no.9 s.280
• /
• pp.624-630
• /
• 2005

To investigate the possibility of the $ZrO_2$ buffer layer as the insulator for the Metal-Ferroelectric-Insulator-semiconductor (MFIS) structure, $ZrO_2$ and $SrBi_2Ta_2O_9$ (SBT) thin films were deposited on the P-type Si(111) wafer by the R.F. magnetron-sputtering method. According to the process with and without the post-annealing of the $ZrO_2$ buffer layer and SBT thin film, the diffusion amount of Sr, Bi, Ta elements show slight difference through the Glow Discharge Spectrometer (GDS) analysis. From X-ray Photoelectron Spectroscopy (XPS) results, we could confirm that the post-annealing process affects the chemical binding condition of the interface between the $ZrO_2$ thin film and the Si substrate. Compared to the MFIS structure without the post-annealing of the $ZrO_2$ buffer layer, memory window value of MFlS structure with post-annealing of the $ZrO_2$ buffer layer were considerably improved. The window memory of the Pt/SBT (260 nm, $800^{\circ}C)/ZrO_2$ (20 nm) structure increases from 0.75 to 2.2 V under the applied voltage of 9 V after post-annealing.