• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.9
• /
• pp.1708-1714
• /
• 2011

AT feeding system of the electric railway system is installed every about 10km at between the feeder and catenary in parallel and the mid-point of the transformer is connected to the rail The supply voltage of this system is doubled than rolling stock voltage. So the voltage drop is smaller than usual. And the other merit of this system is the decreasing inductive disturbance to the communication line because of the reduced current in rail which runs reversed in a point of view of rolling stock. Also, ATP(Auto Transformer Post) is installed to reduce the voltage drop and to mitigate the inductive disturbance, but still now the proper distance between the ATP and AT feeding system is not established which ranges from 2 to 10[km]. The stable result of simulation(which is set that the end of the line AT is installed) to the voltage drop and inductive disturbance can not analyzes the effect to the supply system due to the ATP. This paper analyzes the effect to the system depending on the location of ATP by forecasting the voltage drop and inductive disturbance.

• Journal of Positioning, Navigation, and Timing
• /
• v.6 no.4
• /
• pp.211-221
• /
• 2017

Ellipsodially referenced survey (ERS) is considered as one of the challenging issues in the hydrographic surveys due to the fact that the bathymetric data collected by this technique can be readily transformed either to the geodetic or the chart datum by application of some geoscientific models. Global Navigation Satellite Systems (GNSS) is a preferred technique to determine the ellipsoidal height of a vessel reference point (RP) because it provides cost-effective and unprecedentedly accurate positioning solutions. Especially, the GNSS-derived heights include heave and dynamic draft of a vessel, so as for the reduced bathymetric solutions to be potentially free from these corrections. Although over the last few decades, differential GNSS (DGNSS) has been widely adopted in the bathymetric surveys, it only provides limited accuracy of the vertical component. This technical barrier can be effectively overcome by adopting the so-called GNSS carrier phase (CPH) based techniques, enhancing accuracy of the height solution up to few centimeters. From the positioning algorithm standpoint, the CPH-based techniques are categorized under absolute and relative positioning in post-processing mode; the former is precise point positioning (PPP) correcting errors by the global or regional models, the latter is post-processed kinematic positioning (PPK) that uses the differencing technique to common error sources between two receivers. This study has focused on assessment of achievable accuracy of the ellipsoidal heights obtained from these CPH-based techniques with a view to their applications to hydrographic surveys where project area is, especially, few tens to hundreds kilometers away from the shore. Some field trials have been designed and performed so as to collect GNSS observables on static and kinematic mode. In this paper, details of these tests and processed results are presented and discussed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.204-209
• /
• 1995

The implementation of rapid prototyping technologies has been developed for automotive engineering by utilizing concurrent engineering principes integrated with slective laser sintering. The Selective Laser Sintering, in which a part is generated in layers form powder using a computer-controlled laser scanning apparatus and power feed system. An over view of the basic principles of SLS Machine operation is given. Binding mechanisms are described for power which becomes thermally activated bye the scanning laser beam; viscous flow and melting of a low-melting-point phase in powder. The production of parts from metal is described, including post processing to improve structural integrity and induce a transformation.

• Journal of the Korean housing association
• /
• v.15 no.2
• /
• pp.55-62
• /
• 2004

Apartment design in residential Area is restricted by building distance limit code. Building distance limit decreases gradually to the 0.8H(height), and residential area has 250% site area ratio by building code, so site using has become efficient. In this study, examine the relationship between present building distance limit and right of daylighting environment by computer simulation. As well, high-rise residential officetel and multipurpose residential building becomes increase in commercial non-residential area. In the domestic, residential type multipurpose building made at the business area or central business area has 400∼800% site area ratio by building code. However, at a dweller's point of view, there are much lacks of environmental consideration to provide suitable daylighting environment. And, POE: Post Occupancy Evaluation is not completed yet. In this study, however, progress architectural environment prediction, basis by right of daylighting, and examine the possibility of daylighting by architectural distance limit code in residental area and by high-rise, high-density residential building in non-residental downtown area.

• Journal of Popular Narrative
• /
• v.25 no.4
• /
• pp.191-221
• /
• 2019

This study aims to analyze the post-humanistic imagination that has emerged as a major academic thesis in Korean literature, especially novels. In particular, this paper focuses on Cho Ha-hyung's two novels Chimera's Morning(2004) and A Prefabricated Bodhi Tree(2008), published in the early 2000s, for intensive analysis. Post-humanism can be seen as an extension of post-modernism that tried to overcome the limitations of modernity and seek to establish a new world view. In particular, this thought pays attention to the comprehensive understanding of how the rapid development of science and technology, which has developed since the 20th century, has changed the view of humanity and human-centered civilization itself. At the concrete level, it is developing in the direction of constructing a new subject idea by reflecting and dismantling Western-, reason-, and male-centered power mechanisms that are the core of modern civilization. Cho attempts to discover and re-illuminate the surrounding figures, non-humans, and objects that were not noticed in the classic works written in the past. This ideological flow reflects the fact that the concept of human beings, which had been dominated by the humanities in recent years, has been completely changed, and the natural science and technology perspective is applied to the discourse field in various ways. From the point of view of post-humanism, objects that have not been classified as humans and objects that were considered inferior to humans should be included in human or comparable levels. These questions generate interdisciplinary research tasks by involving the large categories of philosophy, such as ontology, epistemology and empirical fields, as well as calling for the participation of the entire literature, science and social sciences. Against the backdrop of a disaster-hit world, Chimera's Morning and A Prefabricated Bodhi Tree depict human beings as variants transformed by bio-technology, and creatures made out of the artificial intelligence built by computer simulations. Post-humanistic ideas in Cho's novels provide a reflective opportunity to comprehensively reconsider the world's shape and human identity reproduced in the text, and to re-explore boundary lines and hierarchy order that distinguish between human and non-human.

• Asian Pacific Journal of Cancer Prevention
• /
• v.17 no.2
• /
• pp.791-797
• /
• 2016

Background: Punjab state is particularly reporting a rising burden of cancer. A 'door to door cancer awareness and early detection campaign' was therefore launched in the Punjab covering about 2.67 million population, wherein after initial training accredited social health activists (ASHAs) and other health staff conducted a survey for early detection of cancer cases based on a twelve point clinical algorithm. Objective: To ascertain unit cost for undertaking a population-based cancer awareness and early detection campaign. Materials and Methods: Data were collected using bottom-up costing methods. Full economic costs of implementing the campaign from the health system perspective were calculated. Options to meet the likely demand for project activities were further evaluated to examine their worth from the point of view of long-term sustainability. Results: The campaign covered 97% of the state population. A total of 24,659 cases were suspected to have cancer and were referred to health facilities. At the state level, incidence and prevalence of cancer were found to be 90 and 216 per 100,000, respectively. Full economic cost of implementing the campaign in pilot district was USD 117,524. However, the financial cost was approximately USD 6,301. Start-up phase of campaign was more resource intensive (63% of total) than the implementation phase. The economic cost per person contacted and suspected by clinical algorithm was found to be USD 0.20 and USD 40 respectively. Cost per confirmed case under the campaign was 7,043 USD. Conclusions: The campaign was able to screen a reasonably large population. High to high economic cost points towards the fact that the opportunity cost of campaign put a significant burden on health system and other programs. However, generating awareness and early detection strategy adopted in this campaign seems promising in light of fact that organized screening is not in place in India and in many developing countries.

• International Journal of Ocean System Engineering
• /
• v.2 no.4
• /
• pp.209-213
• /
• 2012

Recently, the fuel using in the diesel engines of marine ships has been changed to a low quality of heavy oil because of the steady increase in the price of oil. Therefore, the wear and corrosion in all parts of the engine such as the cylinder liner, piston crown, and spindle and seat ring of exhaust valves has correspondingly increased. The repair welding of a piston crown is a unique method for prolonging its lifetime from an economic point of view. In this case, filler metals with a high corrosion and wear resistance are mainly being used for repair welding. However, often at a job site on a ship, a piston crown is actually welded with mild filler metals. Therefore, in this study, mild filler metals such as CSF350H, E8000B2, and 435 were welded to SS401 steel as the base metal, and the corrosion properties of the weld metals with and without post weld heat treatment were investigated using some electrochemical methods in a 0.1% $H_2SO_4$ solution. The weld metal welded with CSF350H filler metal exhibited the best corrosion resistance among these filler metals, irrespective of the heat treatment. However, the weld metal zones of the E8000B2 and 435 filler metals exhibited better and worse corrosion resistance with the heat treatment, respectively. As a result, it is suggested that in the case of repair welding with CSF350H and 435 filler metals, no heat treatment is advisable, while heat treatment is desirable if E8000B2filler metal is used with repair welding.

• Journal of Periodontal and Implant Science
• /
• v.41 no.2
• /
• pp.79-85
• /
• 2011

Purpose: The aim of this study was to obtain objective and standardized information on masticatory function and patient atisfaction following second molar single implant therap. Methods: Twenty adult patient, who had restored second molar single implants more than 1 month before the study, were enrolled in this stud. All patients received a chewing test using peanuts before and after insertion of the implant prosthesi, with a questionnaire and visual analogue scale (VAS) to evaluate the effect of second molar single implant therap. Results: his study obtained standardized information on the masticatory function objectively (e.g., P, R, $X_{50}$) before (Pre-insertion) and after insertion (Post-insertion) of the implant prosthesis. Masticatory performance (P) after insertion of the implant prosthesis significantly increased from $67.8{\pm}9.9$ to $84.3{\pm}8.5$% (P<0.0001). With the implant prosthesis, the P value increased by 24%. The masticatory efficiency index (R) of Post-insertion is higher than that of Pre-insertion (P<0.0001). With the implant prosthesis, the R value increased by 29%. The median particle size ($X_{50}$) of Post-insertion is lower than that of Preinsertion (P<0.0001). More than 90% of the patients were satisfied with the second molar single implant therapy from a functional point of view. Conclusions: These findings indicate that a second molar single implant can increase masticatory function.

• Information Systems Review
• /
• v.9 no.3
• /
• pp.183-204
• /
• 2007

As the innovation of Information technology in the Public sector is in progress, the "Efficient adaptation and management of information system Act" (passed the National Assembly in December 30, 2005) was established to support the information system planning and development which are systematic and integrated in the enterprise view point. The public sector should adopt Information Technology Architecture into it's organization by the act. This paper reports on the issues, solutions and CSFs (Critical Success Factors) considering the adoption of ITA through the implementation for the case of the Korea Post. To adopt ITA program to the Public sector successfully, Korea Government should set the clear goals for IT A, set the standards for IT A project pricing, and collaborate with the system integration industry to make successful IT A program cases. The case study of Korea Post of MIC will be useful in developing and managing ITA programs for all agencies and organizations considering adoption of ITA.

• English Language & Literature Teaching
• /
• v.15 no.2
• /
• pp.261-280
• /
• 2009

This study focuses on providing the pedagogical implications of stress in English pronunciation teaching since stress is one the most important characteristic factors in English pronunciation (Bolinger, 1976; Brown, 1994; Celce-Murcia, Brinton & Goodwin, 1996; Kreidler, 1989). The author investigated stress production regarding in terms of duration, pitch, and intensity by a group of native speakers of English and a group of low-proficiency South Kyungsang Korean college students for their pre-test. For both of the pre- and post-test, the same stimuli, which consisted of a one-syllable word, two two-syllable words, three three-syllable words, and three four-syllable words, were used along with the various sentence positions: isolation, initial, medial, and final. Soft ware programs, ALVIN and Praat, were used to record and analyze the data. Since Celce-Murcia et al. (1996), Klatt (1975), and Ladefoged (2001) treat duration of the stressed syllable more significantly than other factors, pitch and intensity, with respect to the listener's point of view, the author developed a special method of teaching English stress using a traditional Korean drum to emphasize duration. In addition, the results from the native speakers' production showed that their main strategy to realize stress was through lengthening stressed syllables. After six weeks of stress instruction using the drum, the production of the native speakers and the SK Korean participants from the pre- and post-test were compared. The results from the post-test indicated that the participants showed great improvement not only in duration but also in pitch after the stress instruction. Pitch improvement was unexpected but well-explained by the statement that long vowels receive accent in loan word adaptation in North Kyungsang Korean. The results also showed that the Korean participants' pitch values became more even in their duration values for each syllable as the structure of the word or the sentence became more complex, due to their dependency upon their L1.