• Particle and aerosol research
• /
• v.14 no.4
• /
• pp.145-151
• /
• 2018

Rod shaped Potassium hexatitanate ($K_2Ti_6O_{13}$) was synthesized from colloidal mixture of $TiO_2$, KOH and graphene oxide (GO) by aerosol spray drying and post heat treatment. Firstly, $TiO_2-KOH-GO$ composites were fabricated by aerosol spray drying in argon atmosphere. The composites were then calcined to form a rod shaped morphology of potassium titanate (KTO) in the presence of graphene at $900^{\circ}C$ for 3 h in argon atmosphere. Finally, the rod shaped KTO was obtained after removal of graphene (GR) at $800^{\circ}C$ and 3 h in air atmosphere. Characterization of the synthesized $K_2Ti_6O_{13}$ was carried out using the XRD, BET and FE-SEM. The length and diameter of the synthesized $K_2Ti_6O_{13}$ could be controlled by weight fraction of GO in the aerosol precursor. The length of $K_2Ti_6O_{13}$ rod increased with decreasing its diameter as GO concentration increased. The aspect ratio of the synthesized $K_2Ti_6O_{13}$ rod was controlled from 5 to 13.

• Korean Journal of Metals and Materials
• /
• v.46 no.4
• /
• pp.189-198
• /
• 2008

The changes in microstructure and mechanical properties of AZ31 alloy subjected hot-rolling process were investigated. The AZ31 plates fabricated by horizontal continuous casting process were prepared and have hot-rolled from 30 mm to 1 mm in thickness under different processing conditions. At the rolling temperature of $400^{\circ}C$, little surface and side crack was observed up to 20% reduction rate. As total reduction and reduction rate increase to more than 75% and 20% pass, respectively, Grains were more uniformly refined through overall thickness, and particularly lots of shear bands were appeared to be inclined at less than $20^{\circ}C$ along the rolling direction. Average grain size of less than $5{\mu}m$ and tensile properties of YS ${\geq}$ 250 MPa, UTS ${\geq}$ 300 MPa and El. ${\geq}$ 13% were acquired for hot-rolled AZ31 sheets without post-heat treatment. Maximum intensity of (0002) pole figure was decreased with an increase in reduction rate, indicating the improvement of texture by means of high reduction rate.

• Journal of Powder Materials
• /
• v.30 no.5
• /
• pp.387-393
• /
• 2023

Transition metal chalcogenides are promising cathode materials for next-generation battery systems, particularly sodium-ion batteries. Ni₃Co₆S₈-pitch-derived carbon composite microspheres with a yolk-shell structure (Ni₃Co₆S₈@C-YS) were synthesized through a three-step process: spray pyrolysis, pitch coating, and post-heat treatment process. Ni₃Co₆S₈@C-YS exhibited an impressive reversible capacity of 525.2 mA h g^-1 at a current density of 0.5 A g^-1 over 50 cycles when employed as an anode material for sodium-ion batteries. However, Ni₃Co₆S₈ yolk shell nanopowder (Ni₃Co₆S₈-YS) without pitch-derived carbon demonstrated a continuous decrease in capacity during charging and discharging. The superior sodium-ion storage properties of Ni₃Co₆S₈@C-YS were attributed to the pitch-derived carbon, which effectively adjusted the size and distribution of nanocrystals. The carbon-coated yolk-shell microspheres proposed here hold potential for various metal chalcogenide compounds and can be applied to various fields, including the energy storage field.

• Journal of Powder Materials
• /
• v.31 no.2
• /
• pp.152-162
• /
• 2024

The directed energy deposited (DED) alloys show higher hardness values than the welded alloys due to the finer microstructure following the high cooling rate. However, defects such as microcracks, pores, and the residual stress are remained within the DED alloy. These defects deteriorate the wear behavior so post-processing such as heat treatment and hot isostatic pressing (HIP) are applied to DED alloys to reduce the defects. HIP was chosen in this study because the high pressure and temperature uniformly reduced the defects. The HIP is processed at 1150℃ under 100 MPa for 4 hours. After HIP, microcracks are disappeared and porosity is reduced by 86.9%. Carbides are spherodized due to the interdiffusion of Cr and C between the dendrite and interdendrite region. After HIP, the nanohardness (GPa) of carbides increased from 11.1 to 12, and the Co matrix decreased from 8.8 to 7.9. Vickers hardness (HV) decreased by 18.9 % after HIP. The dislocation density (10^-2/m²) decreased from 7.34 to 0.34 and the residual stress (MPa) changed from tensile 79 to a compressive -246 by HIP. This study indicates that HIP is effective in reducing defects, and the HIP DED Stellite 6 exhibits a higher HV than welded Stellite 6.

• Asian-Australasian Journal of Animal Sciences
• /
• v.18 no.6
• /
• pp.802-806
• /
• 2005

The objective of this study was to determine the effects of processing method and rapeseed variety on ruminal and intestinal protein digestibility of rapeseed meal in steers. Intestinal amino acid digestibility was assessed with an in situ ruminal incubation and precision-fed rooster bioassay. In this experiment one traditional rapeseed meal sample (sample A, prepress extraction) and three double low rapeseed meal samples (sample B, prepress extraction, sample C, screw press and sample D, low temperature press) were placed in polyester bags(8 cm${\times}$12 cm) and suspended in the ventral rumen of steers for 16 h. The residues of in situ incubations were intubated to roosters. Total excreta were collected for 48 h after incubation and then desiccated and amino acid concentrations were determined. Results showed that in ruminal incubation the degradation rate of amino acid and crude protein was higher for traditional rapeseed meal sample A than for double low rapeseed meal sample B, but was much lower than for double low sample C and D. In the group of double low rapeseed meal samples, sample D processed by low temperature press had the highest degradation rate of amino acids in the rumen. For all amino acids, the digestibility of the residual protein as measured by the precision-fed rooster bioassay tended to be lower for sample B than for sample A, which had the same processing method with sample B, and in the group of double low rapeseed meals, sample B had similar digestibility of amino acid in residual protein to sample D and higher than that of sample C. However, although the total amino acid availability involving the digestibility of amino acids in the rumen and rooster bioassay of double low rapeseed meal sample D (low temperature press) was higher than those of the other three samples by 7 to 9 percent, there were no significant differences. Results indicated that processing method markedly affected ruminal and post ruminal amino acid digestibility of rapeseed meal when the temperature exceeded 110$^{\circ}C$. Rapeseed meal that had a high content of fiber was not suitable for dry heat treatment at higher temperatures or the amino acids digestibility in rumen and total availability of amino acids could be reduced. Results also suggested the variety of rapeseed meal had no significant effect on the digestibility and availability of amino acids.

• Korean Journal of Materials Research
• /
• v.9 no.8
• /
• pp.837-842
• /
• 1999

The Ta/TaN multilayer structure with repeating layers of a poly-crystalline Ta layer of high ductility and a TaN layer of high hardness is expected to exhibit toughness. This paper reports the results on the hardness and the adhesion strength of Ta/TaN multilayers and compositional gradient Ta/TaN layers deposited on the high speed steel substrate by reactive sputtering as a function of annealing temperature. The TaN film deposited with the $N_2$/Ar ratio of 0.4 in the reactive sputtering process exhibits the highest crystallinity, and the highest hardness and the results of scratch test of the Ta/TaN multilayers. The hardness and adhesion strength of the Ta/TaN multilayers becomes deteriorated with increasing the annealing temperature in the heat treatment right after depositing the layers. Therefore, post-annealing treatments are not desirable in the case of the Ta/TaN multilayers from the standpoint of mechanical properties. Also the hardness of Ta/TaN multilayers increases with decreasing the compositional modulation wavelength, but the adhesion property of the layers is nearly independent of the wavelength. On the other hand, the compositional gradient Ta/TaN film exhibits the highest hardness and the value of scratch test for the post-annealing temperatures of 20$0^{\circ}C$ and 40$0^{\circ}C$, respectively. This tendency of the compositional gradient Ta/TaN films differs from that of the Ta/TaN multilayers.

• Korean Journal of Materials Research
• /
• v.10 no.6
• /
• pp.437-444
• /
• 2000

We investigated the effect of substrate temperature, chemical composition and post-deposition heat-treatment on the crystal structure and electrical transport of $La_{1-x}Sr_xMnO_{3-{\delta}}$(0.19${\leq}x{\leq}$0.31) thin films. As-prepared $La_{1-x}Sr_xMnO_{3-{\delta}}$ films grown at $500^{\circ}C$ by sputter techniques were found to have the pseudo-tetragonal system(a/c=0.97) and a highly preferential <001> orientation. The films were changed to be of the cubic system by post-deposition annealing at around $900^{\circ}C$. A main target of $La_{0.67}Sr_{0.33}MnO_3$ as well as auxliary targets of $La_{0.3}Sr_{0.7}MnO_3$ ceramics were co-sputtered to control the chemical composition of the film. The Sr content(x) of the film ranged from 0.19 to 0.31, depending on the number of the auxiliary target. When x increased from 0.19 to 0.31, the electrical resistivity of the film decreased and the transition temperature between metal and semiconductor shifted to higher temperature. With a magnetic field of 0.18 T, the magneto-resistance ratio (MR(%) = (${\rho}_o-{\rho}_H/{\rho}_H$) of the $La_{0.69}Sr_{0.31}MnO_3$ thin film was about 390%.

• Horticultural Science & Technology
• /
• v.33 no.6
• /
• pp.923-931
• /
• 2015

This study was conducted to investigate petal pigmentation and the expression patterns of anthocyanin-related genes in bicolored roses 'Pinky Girl' treated with temporal heat stress (THS). Cyanin accumulation in petals was correlated with floral bud development and started rapidly as floral buds began to open, defined as the $4^{th}$ stage of floral bud development ($S_4$). This stage seems to be most susceptible to petal pigmentation. The total of cyanin pigmentation at blooming was significantly decreased (by 45.5%) with exposure to THS ($39/18^{\circ}C$ for three days at $S_4$) in comparison with control. Meanwhile, the expression of anthocyanin-related genes such as CHS, CHI, F3'H, DFR, ANS, 3GT, and 5GT was relatively promoted by THS. Only F3H was less expressed (by 26.7%) with THS treatment; thus, F3H could be a key gene for bicolor promotion in 'Pinky Girl' among anthocyanin-related genes. Overall, the expression pattern of the most anthocyanin-related genes did not match the trends of cyanin pigmentation in petals. These results suggest that floral pigmentation could be associated with other mechanisms related to anthocyanin biosynthesis such as post-translational effects and regulatory genes.

• The Journal of Internal Korean Medicine
• /
• v.26 no.2
• /
• pp.353-359
• /
• 2005

Objectives: Dysphagia is a common in stroke patients. Dysphagia often affects the rehabilitation of stroke patients by increasing the risk of nutritional deficits and aspiration pneumonia. Despite the proliferation of physical therapies including swallowing training, much controversy remains regarding the application and benefit of them. Therefore, in this study, the clinical effect of moxibustion at Chonjung(CV17, Shanzhong) on post-stroke dysphagia were assessed using Swallowing Provocation Test(SPT). Methods: Dysphagia subjects were selected by Dysphagia Screening Test. Swallowing function was tested by Swallowing Provocation Test(sec). Direct moxibustion was applied to the acupoint, Chonjung, five times and Swallowing Provocation Test was performed before and after 30 minute. The Latency Time of Swallowing Reflex (LTSR) was checked by SPT. To find factors related with improving swallowing function, Cold-Heat and Excess-Deficiency Diagnosis were considered. Results: A total of 42 patient were included, but two of them were excluded due to severe coughing. Overall, the swallowing reflex improved significantly. In subgroup analysis on brain lesion, non-brain stem lesion patients significantly improved. Moxibustion was more effective in the cold group than in the heat group, but there were no differences between the Excess and the Deficiency groups. Conclusions: The result of this clinical study suggest that moxibustion at Chonjung(CV17, Shanzhong) is an effective treatment for the dysphagia patients after stroke, especially in non-brain stem lesion and the cold diagnosed patients.

• Journal of the Korean Vacuum Society
• /
• v.17 no.1
• /
• pp.23-27
• /
• 2008

We have investigated the effect of annealing on the structural and optical properties of polycrystalline Ga doped ZnO (GZO) films grown on glass substrates by RF-magnetron sputter at room temperature. The structural and optical properties of as-grown GZO films were characterized and then samples were annealed at $400{\sim}600^{\circ}C$ in $N_2$ ambient for 30, 60 minutes, respectively. The field emission scanning electron microscopy (FE-SEM) and X-ray diffraction (XRD) were used to measure the grain size and the crystalline quality of the films. We found that the crystalline quality was improved and the grain size tends to be increased. The optical properties of GZO thin films were analyzed by UV-VIS-NIR spectrophotometers. It is found that optical properties of thin films are increased by annealing and can be used for transparent electrode application. We believe that the appropriate post-growth heat treatment could be contributed to the improvement of GZO-based devices.