• Journal of Korean Society for Geospatial Information Science
• /
• v.3 no.2 s.6
• /
• pp.15-28
• /
• 1995

The GPS positioning involves not only 'natural' errors associated with the satellites position errors, refraction of EM wave in the ionosphere, etc., but also 'artificial' errors associated with the operation of S/A (Selective Availability). In this paper, we present the principles, accuracies and applicabilities of our personal DGPS method, which employs the position-correction method on the GPS positionings data collected at the reference and the remote sites. The essential requirement of our DGPS method is that two GPS receivers should utilize the identical Navstar satellites at the same time. The positioning error (1 drms) of the stand-alone GPS is of an order of a few tens meters, while that of horizontal position by our DGPS method is about 1m and that of vertical position is about 2m We applied out DGPS technique in positioning moving objects, and obtained satisfactory results in tracking the trajectories of a car on the road and the those of drifters in the sea.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.4 no.3
• /
• pp.243-257
• /
• 2010

Rapid developments in wireless sensor networks have extended many applications, hence, many studies have developed wireless sensor network positioning systems for indoor environments. Among those systems, the Global Position System (GPS) is unsuitable for indoor environments due to Line-Of-Sight (LOS) limitations, while the wireless sensor network is more suitable, given its advantages of low cost, easy installation, and low energy consumption. Due to the complex settings of indoor environments and the high demands for precision, the implementation of an indoor positioning system is difficult to construct. This study adopts a low-cost positioning method that does not require additional hardware, and uses the received signal strength (RSS) values from the receiver node to estimate the distance between the test objects. Since many objects in indoor environments would attenuate the radio signals and cause errors in estimation distances, knowing the path loss exponent (PLE) in an environment is crucial. However, most studies preset a fixed PLE, and then substitute it into a radio propagation loss model to estimate the distance between the test points; such method would lead to serious errors. To address this problem, this study proposes a Path Loss Exponent Estimation Algorithm, which uses only four beacon nodes to construct a radio propagation loss model for an indoor environment, and is able to provide enhanced positioning precision, accurate positioning services, low cost, and high efficiency.

• Journal of Korea Multimedia Society
• /
• v.14 no.3
• /
• pp.433-439
• /
• 2011

The positioning system based on wireless AP collects AP information distributed in the real world, stores it into database, and measures the position objects by comparing with searched AP information. The existing fingerprinting method is a probabilistic modeling method that acquires much of the data collected from one location upon database composition, and stores the average of the data for the sake of use it in positioning objects. Using the average value, however, may cause the probability of errors Such errors are fatal weaknesses for services based on the accurate position. This paper described the characteristics and problems of the previously used wireless AP positioning system, and proposed a method of using the AP DB and an MSS mechanism for outdoor positioning in order to solve the aforementioned problems. And the results obtained from experimental tests showed that the proposed method achieved very low error rate(27%) compared with the existing method.

• Journal of Positioning, Navigation, and Timing
• /
• v.4 no.2
• /
• pp.73-77
• /
• 2015

Global Positioning System (GPS) Precise Point Positioning (PPP) has been extensively used for geodetic applications. Since December 2012, BeiDou navigation satellite system has provided regional positioning, navigation and timing (PNT) services over the Asia-Pacific region. Recently, many studies on BeiDou system have been conducted, particularly in the area of precise orbit determination and precise positioning. In this paper PPP method based on BeiDou observations are presented. GPS and BeiDou data obtained from Mokpo (MKPO) station are processed using the Korea Astronomy and Space Science Institute Global Navigation Satellite System (GNSS) PPP software. The positions are derived from the GPS PPP, BeiDou B₁/B₂ PPP and BeiDou B₁/B₃ PPP, respectively. The position errors on BeiDou PPP show a mean bias < 2 cm in the east and north components and approximately 3 cm in the vertical component. It indicates that BeiDou PPP is ready for the precise positioning applications in the Asia-Pacific region. In addition, BeiDou tropospheric zenith total delay (ZTD) is compared to GPS ZTD at MKPO station. The mean value of their difference is approximately 0.52 cm.

• Journal of Astronomy and Space Sciences
• /
• v.28 no.3
• /
• pp.217-223
• /
• 2011

Precise point positioning (PPP) is increasingly used in several parts such as monitoring of crustal movement and maintaining an international terrestrial reference frame using global positioning system (GPS) measurements. An accuracy of PPP data processing has been increased due to the use of the more precise satellite orbit/clock products. In this study we developed PPP algorithm that utilizes data collected by a GPS receiver. The measurement error modelling including the tropospheric error and the tidal model in data processing was considered to improve the positioning accuracy. The extended Kalman filter has been also employed to estimate the state parameters such as positioning information and float ambiguities. For the verification, we compared our results to other of International GNSS Service analysis center. As a result, the mean errors of the estimated position on the East-West, North-South and Up-Down direction for the five days were 0.9 cm, 0.32 cm, and 1.14 cm in 95% confidence level.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.6
• /
• pp.2601-2610
• /
• 2013

The main limiting factors of Precise Point Positioning(PPP) accuracy are errors in broadcast satellite orbits, clock errors, and the others, which are receiver-dependent errors(ionospheric, tropospheric refraction, multipath, and tides, etc.). Therefore, to facilitate high precision PPP, precise orbits/clocks corrections, the receiver-dependent errors corrections have to apply to multi frequency GNSS measurements for an ionosphere free combination and integer ambiguity resolution in real-time. Currently, there are many Analysis Centers, which offer the precise corrections stream computed in real-time using the global or regional GNSS tracking network. The goles of this research considered performances of the real-time static PPP with using RTCM corrections from NTRIP casters. For this, the corrections streams of Analysis Centers received via NTRIP does apply to GNSS data of check points individually, as well as jointly, in accordance with various session lengths. After that, have compared the PPP results from the corrections streams with each other, and with Standard Point Positioning(SPP) results.

• Proceedings of the KSR Conference
• /
• 2011.05a
• /
• pp.343-349
• /
• 2011

Now, for the continuous location detection of train, the method that the moving distance of a vehicle is detected using an wheel sensor(odometer) mounted within a train, is generally used. It has a problem that the positioning errors of a train can be accumulated as the moving distance increases. To solve this problem, it is required to apply a variety of positioning sensors and to integrate with sensor data. In this paper, we develop the train-borne positioning system applicable to the conventional railway and high-speed railway, and verify the performance of the train-borne positioning system through a vehicle test.

• Journal of Advanced Marine Engineering and Technology
• /
• v.24 no.1
• /
• pp.119-126
• /
• 2000

In constructing the positioning system based on a conventional dead-reckoning for a wheeled vehicle with pneumatic tires, the position estimation error is inevitable as changes of the radius of the wheels depend on live load and variable enviroment. Therefore, this paper proposes the positioning system which can estimate the error source i.e. the vehicle parameter errors, such as the right and left wheel radius error, using gyroscope and ultrasonic sensor and correct the parameter to reduce the dead-reckoned position estimation error. The extended Kalman filter was used as a method for the multisensor data fusion. The simulation to verify the effectiveness of the proposed positioning system is performed.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.795-800
• /
• 2008

The paper presents research for the established experiment environment of multi vehicle robot, localization algorithm that is based on vehicle control, and path tracking. The established experiment environment consists of ultrasonic positioning system, vehicle robot, server and wireless module. Ultrasonic positioning system measures positioning for using ultrasonic sensor and generates many errors because of the influence of environment such as a reflection of wall. For a solution of this fact, localization algorithm is proposed to determine a location using vehicle kinematics and selection of a reliable location data. And path tracking algorithm is proposed to apply localization algorithm and LOS, finally, that algorithms are verified via simulation and experimental

• Journal of IKEEE
• /
• v.26 no.1
• /
• pp.67-76
• /
• 2022

In this paper, we propose a new algorithm to improve the accuracy of the Wi-Fi access point (AP) positioning technique. The proposed algorithm based on evaluating the trustworthiness of the signal strength quality of each measurement node is superior to other existing AP positioning algorithms, such as the centroid, weighted centroid, multilateration, and radio distance ratio methods, owing to advantages such as reduction of distance errors during positioning, reduction of complexity, and ease of implementation. To validate the performance of the proposed algorithm, we conducted experiments in a complex indoor environment with multiple walls and obstacles, multiple office rooms, corridors, and lobby, and measured the corresponding AP signal strength value at several specific points based on their coordinates. Using the proposed algorithm, we can obtain more accurate positioning results of the APs for use in research or industrial applications, such as finding rogue APs, creating radio maps, or estimating the radio frequency propagation properties in an area.