• Polymer(Korea)
• /
• v.24 no.5
• /
• pp.728-735
• /
• 2000

Fentanyl-loaded biodegradable poly(L-lactide-co-glycolide) (75 : 25 by mole ratio of lactide to glycolide, PLGA) microspheres (MSs) were prepared to study the possibility for long-acting local anesthesia. We developed the fentanyl base (FB, slightly water-soluble)-loaded PLGA MSs by means of conventional O/W solvent evaporation method. The size of MSs was in the range of 10~150 ${\mu}{\textrm}{m}$. The morphology of MSs was characterized by SEM, and the in vitro release amounts of FB were analyzed by HPLC. The lowest porous cross-sectional morphology and the highest encapsulation efficiency were obtained by using gelatin as an emulsifier. The influences of several preparation parameters, such as emulsifier types, molecular weights and concentrations of PLGA, and initial drug loading amount, etc., have been observed in the release patterns of FB. The release of FB in vitro was more prolonged over 25 days, with close to zero-order pattern by controlling the preparation parameters. We also investigated the physicochemical properties of FB-loaded PLGA MSs by X-ray diffraction and differential scanning calorimeter.

• Korean Journal of Materials Research
• /
• v.24 no.2
• /
• pp.111-115
• /
• 2014

Titanium and its alloys are useful for implant materials. In this study, porous Ti-Nb-Zr biomaterials were successfully synthesized by powder metallurgy using a $NH_4HCO_3$ as space holder and $TiH_2$ as foaming agent. Consolidation of powder was accomplished by spark plasma sintering process(SPS) at $850^{\circ}C$ under 30 MPa condition. The effect of high energy milling time on pore size and distribution in Ti-Nb-Zr alloys with space holder($NH_4HCO_3$) was investigated by optical microscope(OM), scanning electron microscope(SEM) & energy dispersive spectroscopy(EDS) and X-ray diffraction(XRD). Microstructure observation revealed that, a lot of pores were uniformly distributed in the Ti-Nb-Zr alloys as size of about $30-100{\mu}m$ using mixed powder and milled powders. In addition, the pore ratio was found to be about 5-20% by image analysis, using an image analyzer(Image Pro Plus). Furthermore, the physical properties of specimens were improved with increasing milling time as results of hardness, relative density, compressive strength and Young's modulus. Particularly Young's modulus of the sintered alloy using 4h milled powder reached 52 GPa which is similar to bone elastic modulus.

• Membrane Journal
• /
• v.24 no.6
• /
• pp.438-447
• /
• 2014

The amorphous and porous borosilicate without any cracks was obtained under the following condition : 0.01~ 0.10 mole ratio of trimethylborate (TMB)/ tetraethylorthosilicate (TEOS) and the temperature of $700{\sim}800^{\circ}C$. According to the BET and SEM measurements, borosilicate heat-treated in between 700 and $800^{\circ}C$ showed the surface area of $251.12{\sim}355.62m^2/g$, the pore diameter of 3.5~4.9 nm, and the particle size of 30~60 nm. According to the TGA measurements, the thermal stability of poly[1-(trimethylsilyl)propyne](PTMSP) membrane was enhanced by inserting borosilicate. SEM observation showed that the size of dispersed borosilicate in the composite membrane was $1{\mu}m$. The results showed that the permeability of $H_2$ and $N_2$ increased and the selectivity of $H_2/N_2$ decreased upon the addition of borosilicate into PTMSP membranes. Addition of borosilicate may possibly increase the free volume, cavity and porosity of membranes indicating that permeation occurred by molecular sieving, surface and Knudsen diffusion rather than solution diffusion of gases.

• Membrane and Water Treatment
• /
• v.6 no.3
• /
• pp.205-224
• /
• 2015

A novel hydrophilic poly (vinylidene fluoride)/poly (p-phenylene terephthalamide) (PVDF/PPTA) blend membrane was prepared by in situ polycondensation of p-phenylene diamine (PPD) and terephthaloyl chloride (TPC) in PVDF solution with subsequent nonsolvent induced phase separation (NIPS) process. For comparison, conventional solution blend membrane was prepared directly by adding PVDF powder into PPTA polycondensation solution. Blend membranes were characterized by means of viscometry, X-ray photoelectron spectroscopy (XPS), Field Emission Scanning Electron Microscopy (FESEM). The effects of different blending methods on membrane performance including water contact angle (WCA), mechanical strength, anti-fouling and anti-compression properties were investigated and compared. Stronger interactions between PVDF and PPTA in in situ blend membranes were verified by viscosity and XPS analysis. The incorporation of PPTA accelerated the demixing rate and caused the formation of a more porous structure in blend membranes. In situ blend membranes exhibited better hydrophilicity and higher tensile strength. The optimal values of WCA and tensile strength were $65^{\circ}$ and 34.1 MPa, which were reduced by 26.1% and increased by 26.3% compared with pure PVDF membrane. Additionally, antifouling properties of in situ blend membranes were greatly improved than pure PVDF membrane with an increasing of flux recovery ratio by 25%. Excellent anti-compression properties were obtained in in situ blend membranes with a stable pore morphology. The correlations among membrane formation mechanism, structure and performance were also discussed.

• Proceedings of the SAREK Conference
• /
• 2008.11a
• /
• pp.618-623
• /
• 2008

To enhancement heat transfer performance, the metallic foam as heat exchanger was studied rapidly. This was attributed to its high surface area to volume ratio as well as intensive flow mixing by tortuous flow passages. So the experimental study about the heat transfer characteristic of metallic foam is presented in this paper. The material in this experiment was used as FeCrAl which has density of 10 ppi, 20 ppi and 30 ppi respectively. And the results show the heat transfer is rise with permeability Reynolds number increase and the pressure drop metallic foam was increased with the ppi increase.

• Membrane Journal
• /
• v.2 no.1
• /
• pp.21-32
• /
• 1992

Hydrogen-permselective silica membranes were synthesized within tim walls of porous Vycor tubes by chemical vapor depostion of $SiO_2$. Film deposition was carried out using $SiCl_4$ hydrolysis either in the oppm shag reactants or in the one-sided geometry. At temperatures above $600^{\circ}C$ the permeation rate of hydrogen thorough the silica films varied between 0.01 and $025cm^3(STP)/cm^2-min-atm$ depending on the reaction geometry and the $H_2 : N_2$ permeation ratio was about 1000. Permeation rates of both $H_2$ and $N_2$ increased with increasing temperature. The silica membranes produced by one-sided deposition have higher hydrogen permmeation rates than those produced by the opposing reactants geometry although the membranes formed in an opposing reactants geometry were relatively stable during the heat treatment or after exposure to ambient air. These membranes can be applied to high temperature gas separations or membrane reactors once the film deposition process is optimized to get high permeability as well as good stability.

• Resources Recycling
• /
• v.25 no.3
• /
• pp.74-81
• /
• 2016

Study on chlorination of ilmenite ore were carried out by using PVC(polyvinyl chloride) as the chlorinating agent in a static bed reactor for selective removal of iron. The effect of amount of PVC and reaction temperature were investigated. It was found that the removal ratio of iron increased with amount of PVC and temperature. After reaction with HCl gas generated from PVC, porous surface of the specimens were observed. As a result, HCl gas could react with iron in the central portion of ilmenite particle through these pores. Examination of data using kinetic model suggest that the selective chlorination rate is controlled by chemical reaction at the interface of particles. The activation energy for the selective chlorination of ilmenite using PVC was calculated as 20.47 kJ/mol.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.5
• /
• pp.2979-2984
• /
• 2015

This paper has presented a new foaming technology of selective hybrid-structured polymer film with expanded pores. The porous structure of closed pore was firstly fabricated by applying the 355nm UV-pulsed laser to 0.1mm thick film that was uniformly mixed with PP pellets, copper powder, and CBA (Chemical Blowing Agent). In order to expand pore size of closed-cell shape, LAMO(Laser Aided Micro pore Opening) processing was conducted to heat the copper powder, and then the bigger pore size of closed-cell more than existing pore size was successfully formed because of rapid conduction of heated metal powder. From the experimental results, various process parameters such as laser fluence, intensity, scan rate, spot size and density of powder and CBA were considerably considered to reveal the correlation among the pore characteristics. In the future, a function experiment will be carried out to use the hybrid film of industrial applications.

• Journal of the Korean Applied Science and Technology
• /
• v.31 no.3
• /
• pp.408-415
• /
• 2014

In order to prepare high-quality activated carbons (ACs), coal tar pitch (CTP), and mixtures of CTP and petroleum pitch (PP) were activated with KOH. The ACs prepared by activation of CTP in the range of $700{\sim}1000^{\circ}C$ for 1~5 h had very porous textures with large specific surface areas of $2470{\sim}3081m^2/g$. The optimal activation conditions of CTP were determined as CTP/KOH ratio of 1:4, activation temperature of $900^{\circ}C$, and activation time of 3 h. The obtained AC showed the highest micro-pore volume, and pretty high specific surface area and meso-pore volume. The micro-pore volumes and specific areas of activated mixtures of CTP and PP were similar to each other but the meso-pore volume could be increased. In order to change the degree of crystallinity of precursors before KOH activation process, the CTPs were carbonized in the range of $500{\sim}900^{\circ}C$. As the carbonization temperature increased, the specific surface area and pore volume of the activated ACs with the same activation conditions for CTP decreased dramatically. It was demonstrated that the increased pore size distribution of AC electrodes in the range of 1 to 2 nm plays an important role in the performance of electric double-layer capacitor.

• Food Engineering Progress
• /
• v.15 no.1
• /
• pp.15-21
• /
• 2011

The effects of replacement of wheat flour with 10, 20, and 30% chestnut flour on the bread-making properties and quality characteristics of bread were evaluated. Among the physical characteristics of the dough, the development time in the farinogram decreased with increasing amounts of chestnut flour, and the dough stability and durability were reduced. In the amylogram, there was a slight increase in the gelatinization starting temperature when compared to the control flour, but the maximum viscosity gradually decreased in response to increasing amounts of chestnut flour. The expansion ratio did not increase in the dough containing 20 or 30% chestnut flour. Moreover, the loaf volume and specific volume of bread containing 20 and 30% chestnut flour were smaller than those of the control and the 10% treatment. The hardness of bread containing 10% chestnut flour($700g/cm^2$) was lower than that of the other treatments($1413-1,627g/cm^2$). Furthermore, bread containing 10% chestnut flour had denser porous structures than the other treatments. The sensory evaluation tests revealed that the 10% treatment had higher sensory scores for the internal and external qualities of bread than the other treatments.