• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.1655-1657
• /
• 2004

The electrical fire frequently happens through carelessness of a vinyl and rubber cords such as a poor contact, a mechanical stress and so on. Electrical fire occupies the greater part(about 30%) of all fires in Korea. In this paper, we compared to the fire dispersive patterns of vinyl and rubber cords according to the external flame in the wall-model. The fire progress and dispersive patterns were measured by a high speed imaging system(HG-100K, REDLAKE, USA). From the results, short-circuit of the vinyl cords are easy to happen than the rubber cords by the external flame. The pattern of fire was progressed a flashover, scattering and disconnection. The fire progress on the vinyl cord is not observed because the ignition energy decreases. However, the fire was progressed continuously on the rubber cord.

• Korean Journal of Materials Research
• /
• v.13 no.3
• /
• pp.160-168
• /
• 2003

The co-firing processes for the supported type planar solid oxide fuel cell were investigated. A flat cell of $7.7${\times}$10.8\textrm{cm}^2$ was fabricated successfully by the co-firing process, in which green films were co-sintered in the forms of two layers of anode/electrolyte or of three layers of anode/electrolyte/cathode with gas distributor. A co-fired cell of two layers yielded a power of 200 ㎽/$\textrm{cm}^2$ at 608 ㎷. Its performance loss was mainly due to iR drop in the anodic gas distributor, which was attributed to poor contact between anodic gas distributor and current collector. The performance in the co-fired cell of three layers was much lower than that of two layers, which resulted from the large iR drop and activation overvoltage at the cathodic side. In the co-fired cell of two layers, the impedance analysis indicated that the performance decay during cell operation is due to both anode overvoltage and iR drop at anode side. Also the electrode reaction of the co-fired two layers' cell is considered to be controlled by activation overvoltage within the low current of 50 ㎃.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.4
• /
• pp.247-254
• /
• 2015

Ride comfort is one of the major factors in evaluating the performance of the vehicle. Tire is closely related to the ride comfort of the vehicle as the only parts in contact with the road surface directly. Vertical stiffness which is one of the parameters to evaluate the tire performance is great influence on the ride comfort. In general, the lower the vertical stiffness, the ride comfort is improved. Research for improving the ride comfort has been mainly carried out by optimizing the shape of the pneumatic tire. However, demand for safety of the vehicle has been increased recently such as a run-flat tire which is effective in safety improvement. But a run-flat tire have trouble in practical use because of poor ride comfort than general tire. Therefore, In this paper, the research was carried out for improving the ride comfort through the optimization of the SIR shape inside a run-flat tire. Meta-model was generated by using the design of experiment and it was able to reduce the time for the finite element analysis of optimization. In addition, Shape optimization for improving the ride comfort was performed by using the genetic algorithm which is one of the global optimization techniques.

• Journal of the Korean Society of Safety
• /
• v.30 no.4
• /
• pp.20-25
• /
• 2015

In general, the causes of the electrical fire are overcurrent, short circuit, poor contact, etc. This study is aimed to recognize the risk of electric arc to prevent electrical fires due to the conductive dust accumulated on the circuit breaker. The experiment was carried out by the method that conductive metal dust collected from the field is being accumulated on the experimental electrodes with gap of 13 mm until the arc is generated. In case that arc was generated, the amount of conductive dust was measured and the thickness was calculated. This experiments was conducted by particle size. In order to distinguish particle size, mesh size(60~100, 100~150, 150~200, 200~250mesh) was classified using a sieve. As the results of experiment for each of the particle sizes, it was confirmed that there is differences in the generation of arc depending on the thickness of dust accumulated.

• Journal of Korean Association for Spatial Structures
• /
• v.11 no.3
• /
• pp.77-83
• /
• 2011

Laminated composite plates have shown their superiority over metals in applications requiring high specific strength, high specific modulus, and so on. Therefore, they have used in various industry. However, they have poor resistance to impact compared to typical metal materials. To resolve this problem by many researchers for a variety of studies have been attempted. This study investigates characteristic of impact behavior of laminated composite plates due to initial stress. Using finite element program which involved the indentation law, we investigate characteristic of impact behavior of laminated composite plates due to initial stress.

• Korean Journal of Health Education and Promotion
• /
• v.24 no.4
• /
• pp.231-240
• /
• 2007

The hospital setting provides many opportunities for health promotion. There are many health professionals including physicians, nurses, medical technicians who have close contact with patients and their family. Health professionals are very influential to arouse the awareness about health and illness, and to motivate to change lifestyle among patients. Thus health professionals are most effective and important human resources for health education for patients to improve recovery rates and to promote health. In spite of the importance of health professionals' role in health promotion, the Korean government has provided little support for their health education for patients. Most of the health professionals have not learned about health education theories and skills, and have little attention to educate patients to change their lifestyle. Also the health professionals themselves have relatively poor lifestyle compared with advanced western countries. To improve health education for patients and their family, following strategies and policies should be considered: reinforcing curriculum for health education in college and training course, providing practical incentives for patient education, capacity building for health education and developing guideline for patient education, training health educators, networking and collaborating between community health center and hospitals, promoting the importance of health education among patients, researching and developing health education theory and practice including cost-benefit of health education.

• Tribology and Lubricants
• /
• v.36 no.4
• /
• pp.232-243
• /
• 2020

It is essential to predict the amount of wear and surface parameters for a surface where relative motion occurs. In the asperity-based model for wear prediction, only the average contact pressure can be obtained. Hence, the accuracy of wear analysis is poor. In this study, DC-FFT is used to obtain the pressure of each node, and wear analysis is performed by considering the effect of the pressure gradient. The numerical surface generation method is used to create Gaussian, negatively skewed, and positively skewed surfaces for wear analysis. The spatial and height distributions of each surface are analyzed to confirm the effectiveness of the generated surface. Furthermore, wear analysis is performed using DC-FFT and Archard's wear formula. After analysis, it is confirmed that all peaks are removed and only valleys remain on the surface. The RMS roughness and Sk continue to decrease and Ku increases as the cycle progresses. It is observed that the surface parameters are significantly affected by the radius of curvature of the asperity. This analysis method is more accurate than the existing average wear and truncation models because the change in asperity shape during the wear process is reflected in detail.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.333-333
• /
• 2013

The poor conductivity of poly (3,4-ethylene dioxythiophene): poly (styrenesulfonate) (PEDOT:PSS) film hinders to use for a flexible electrode in solar cells. In this report we demonstrate that the conductivity of PEDOT:PSS film can be enhanced by modifying structures in a mixture of PEDOT: PSS aqueous solution and various organic solvents such as polar protic (2-propanol, methanol, ethanol, formic acid) and aprotic solvents (acetone and acetonitrile). To comparatively study the structural effects on the resulted electrical properties, the films are spin-coated on glasses and ITO. At the same time, a contact angle goniometer is used for clarifying a mechanism of wettability of PEDOT (hydrophobic) and PSS (hydrophilic) on the observed conductivity. The structures and electrical properties are investigated by FE-SEM (Field Emission Scanning Electron Microscopy), AFM (Atomic Force Microscopy), and 4-point probe, respectively.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.7
• /
• pp.1561-1568
• /
• 2005

In client-solver environments, clients can execute applications without contact a server by storing data in its cache. To guarantee correction of applications, we need a cache consistency algorithm. Many cache consistency algorithms have been proposed, these were categorized by detection-based and avoidance-based algorithms. In this paper, we propose a new detection-based cache consistency algorithm that can reduce a burden of a client that has poor resource compare with a server Our method controls concurrency of transactions using timestamp ordering and updates a cache dynamically. In addition to we show that our method maintains a one-copy serializability.

• Tribology and Lubricants
• /
• v.12 no.3
• /
• pp.12-25
• /
• 1996

The friction and wear behaviors of ceramics against steels with lubricants were investigated and compared with those observed in air. Lubrications wbre done by a water and a commercial engine oil as received. The investigated ceramics were $Al_{2}O_{3}$, SiC, and $Si_{3}N_{4}$. Steels with 0.2 wt.% C were heat treated to obtain tempered structure. A cylinder-on-plate tribometer with rotated sliding motion was used to carry out the experiments. In the experiments reported here, the ranges of different testing speeds and loads were used. It was found that the friction and wear characteristics of tested pairs were significantly influenced by environments. In water and oil environments the wear of ceramics was reduced from 10$^{-6}$ g/s down to 10$^{-8}$ g/s in dry sliding at the same values of the frictional power which are the products of the friction coefficient, the load and the sliding speed. SiC showed excellent wear resistant behavior in water sliding, which was the lowest among tested ceramics, but it was, very poor in oils. In case of $Si_{3}N_{4}$, the wear rates were very low under oil environment, but the highest in water. The wear rates of $Al_{2}O_{3}$ were very low in both lubricating conditions at low values of the frictional power, but high at high values of the frictional power.