최근 polyolefin계열의 고분자 분리막이 많이 사용되고 있는데 특히 그 중 polypropylene막은 특성상 내약품성 및 내열성이 뛰어나 막 손상이나 성능 저하가 비교적 적은 고분자 막으로 평가되고 있다. 그러나 재질의 소수성 특성 때문에 심각한 fouling을 유발하게 되어 이를 방지하기 위해 막 표면을 hydrophilic agent로 개질 시켜 fouling을 제어하는 기술이 진행되고 있다. 일반적으로 막 재질을 개질 시키기 위하여 sulfonating agents, ozone, 그리고 hydrophilic monomer등을 grafting하는 방법들이 사용되고 있는데, 이는 공정상의 어려움이 있고 완벽한 친수성의 부여를 기대하기가 어렵다. 또한 막 기공 구조의 변화와 붕괴를 초래한다는 단점이 있다. 이밖에 hydrophilizing agent 등을 이용하여 wetting시킴으로써 일시적인 친수화 처리를 하는 방법이 있다. 그러나 이 방법은 membrane matrix로 부터 hydrophilizing agent가 새어 나가므로 영구적으로 사용할 수 없으며, 특히 의료용 분리막으로 이용될 경우 유출된 hydrophilizing agent가 cell membrane을 공격하여 cell 분해와 같은 인체에 해로운 결과를 초래하기 때문에 부적당하다. 최근 들어 저온 plasma를 이용한 표면 개질의 방법이 연구되고 있는데, 이는 plasma가 고분자 물질의 구조나 화학적 반응성과는 상관없이 모든 고분자 물질의 표면을 일정하게 개질 시킬 수 있으며 여타의 다른 방법들과는 달리 막 제조시 residual solvent의 문제점과 swelling의 문제점들이 발생하지 않는 장점 때문에 최근 각광받고 있는 기술 중의 하나이다. 또한 다른 방법에 비해 막과 plasma와의 강한 흡착력 때문에 영구적 친수성을 가지게 할 수 있다. 본 연구에서는 저온 plasma를 이용한 표면 개질이 막의 친수성 향상 및 fouling 방지에 미치는 영향에 대하여 조사하였다.
In this paper, we analysed the properties change of electric wire when the thermal stress was applied to NFR-8 and FR-PVC [600] wire. Measurement is made of the attenuation of a light beam by smoke accumulating with in a closed chamber due to nonflamining pyrolytic decomposition and flaming combustion. Results are expressed in terms of specific optical density which is derived from a geometrical factor and the measured optical density a measurement characteristic of the concentration of smoke. Referenced documents were ASTM E662 standard test method for specific Ds generated by solid materials. The furnace control system shall maintain the required irradiance level under steady-state condition with the chamber door closed of 2.5${\pm}$0.04[w/$\textrm{cm}^2$] for 20 min. According to the results of the smoke density analysis of NFR-8 and FR-PVC the highest decomposition flaming smoke density range of NFR-8 and FR-PVC were 7.2 to 77.5 and 51.1 respectively. Nonflaming smoke density range of NFR-8 and FR-PVC were 100.4 to 112.2 and 126.5 to 398.8. The amount of carbon monoxide generated was found to be much higher in FR-PVC decomposition than in NFR-8 due to incomp1ete combustion of FR-PVC which has high content of carbon in compound.
본 연구에서는 CFRP 보강근과 고강도콘크리트의 부착강도에 미치는 보강섬유의 표면처리 방법의 효과를 평가하였다. 표면을 친수성 물질로 코팅된 구조용 PVA 섬유 및 기하학적 변형으로 변형된 절곡형 폴리올레핀계 구조용 합성섬유를 보강섬유로 사용하였다. 섬유의 표면처리 방법에 따른 고강도콘크리트의 강도특성을 평가하기 위하여 압축강도 실험을 실시하였다. 고강도콘크리트와 CFRP 보강근 사이의 부착특성은 직접 부착강도시험을 의하여 평가하였다. 시험 결과는 섬유의 표면처리 방법은 고강도콘크리트와 CFRP 보강근 사이의 부착거동에 영향을 미쳤다. 또한 고강도콘크리트에 섬유의 첨가는 할렬균열의 발생 및 성장을 조절함으로써 고강도콘크리트와 CFRP 보강근 사이의 부착거동, 부착강도 및 상대부착강도의 증가시켰다.
카본슬러리 연료 제조 시 카본의 분산안정성에 미치는 공정변수의 영향을 조사하였다. 카본슬러리연료의 분산안정성은 위치별 입도분석, 카본함량 분석, 그리고 원심분리 후 분산상태 관찰을 통해서 측정하였다. 여러 종류의 첨가제를 적용한 결과, NB463S84 사용시 분산성과 분산안정성이 가장 우수한 것을 알 수 있었다. NB463S84와 비슷한 작용기를 가지는 PIBSI를 합성하였으며, 이를 카본슬러리 연료에 적용하여 유사한 분산안정도를 얻었다. 끝으로 g 규모에서 얻은 제조 조건을 kg 규모 제조에 적용하여 카본슬러리 연료의 실용화 가능성을 확인하였다.
폐아스콘은 순재료와 첨가제를 섞어 분쇄와 가열을 통하여 재활용될 수 있다. 본 연구에서는 고품질재생아스팔트(SRP)의 질을 향상시키기 위하여 Sasol 왁스와 폴리올레핀 탄성체를 이용하였다. 첨가제로써 중간층 및 표층용은 PG 70-22를 목표로 아스팔트량의 1.5%를 사용하였고, 중교통 표층용은 PG 76-22를 목표로 아스팔트량의 3% 개질제와 혼합물의 0.1%에 해당하는 셀룰로스 화이버를 첨가하였다. 두 혼합물은 마샬안정도시험, 간접인장강도시험, 잔류간접인장강도시험, 휠트래킹시험 등을 수행하였다. 시험결과는 KS F 2349와 GR F 4005의 기준을 만족하였으며, 고품질재생아스팔트는 중교통도로의 표층 및 기층재료로 사용이 적합하였다. 현재 약 13,000톤의 고품질재생아스팔트 혼합물이 서울 올림픽 도로에 현장시공 되었다.
PO 필름 공급이 경북 성주지역 참외 산업에 미치는 영향을 분석하기 위하여 참외 재배면적, 재배 농가수, 수량 및 소득 등을 분석한 결과, PE 필름은 2010년에 비해 2014년도에는 전국, 경북 성주 지역에서 각각 91.5%, 94.9%, 95.2%로 감소한 반면, PO 필름 보급은 각각 342.5%, 500%, 825% 이었다. 2010년에 비해 2015년 재배면적과 농가수는 각각 8.8%, 11.9% 감소하였다. 수량과 생산량은 각각 38.2%, 25.9% 증가하였다. 조수입은 2010년 3,051 억원에서 2015년 4,020 억원으로 1.3배 증가하였고 소득도 2010년 1,936 억원에서 2015년 4,020 억원으로 2.7배 증가하였다. 이상의 결과를 종합 하면 PO 필름으로 교체되면서, 참외 생산성은 증대되고, 작업 노력 및 유해물질 배출은 감소될 것으로 보여진다.
Additives in plastics are capable of migrating from the packaging materials into the foodstuffs, thereby presenting a source of contamination and a potential health risk to the consumer. The migration from packaging materials into foodstuffs is first of all regulated by examining the amounts of global and specific migrated components. Besides, there is worldwide still a need for practical methods for measuring and monitoring migration from polymers, especially for the testing of migration into fatty foodstuffs. Therefore, these studies were undertaken to investigate the safety status of domestic plastic packaging materials with respect to migration. Another objective of this study was to examine the applicability of ethanol as an alternative fatty food simulant substituting for olive oil and n-heptane. The evaporation residues for various dometic plastic samples determined as described in Korean food laws were in the level from 4.3 to 14.5 mg/$\ell$, which were much lower than the limit value of 150 mg/$\ell$. The global migration values into 95 % ethanol showed to be comparable to those into n-heptane, while the olive oil migration values were comparably higher than those into ethanol or n-heptane and moreover they were not reproducible. The kinetic migration begavior of additives in polyolefin samples into 95% ethanol showed a Fickian diffusion process. The results of these studies on global migration and kinetic testings demonstrate that the ethanol could be successfully substitute for the olive oil and n-heptane as an alternative fatty food simulant, at least in contact with polyoefins.
은 나노와이어는 금속 특유의 고전도 특성, 낮은 Percolation threshold 및 고투과 특성을 나타내어 차세대 투명전극 물질로 각광받고 있다. 이를 플렉서블 및 웨어러블 디바이스, 전자피부 디바이스 등과 같은 다양한 분야에 활용하기 위해서는 은 나노와이어 전극을 필요한 형태로 패터닝 하기 위한 기술이 필수적으로 요구된다. 일반적으로, 은 나노와이어를 패터닝하기 위한 공법으로는 포토리소그래피 및 에칭, 프린팅, 레이저 Ablation 등을 들 수 있으나, 이러한 패터닝 기술들은 공정 절차가 복잡하거나 높은 공정 비용 등의 단점이 있다. 이에 본 연구에서는 UV-curable 점착제 기반의 low-cost 은 나노와이어 패터닝 공법을 개발하고자 하였다. 은 나노와이어 네트워크가 형성된 폴리우레탄 필름에 UV 경화형 테이프를 부착하고, UV를 선택적으로 조사한 뒤, 다시 UV 경화형 테이프를 벗겨내는 3단계의 간단한 공정만으로 은 나노와이어 패턴을 성공적으로 형성할 수 있었으며, 간단한 구현 원리 및 분석 결과를 본 논문에서 보고하고자 한다.
To use effectively the solar energy in greenhouse heating, a high performance solar collector should be developed. And then the size of the solar collector and thermal storage tank should be determined through the calculation of heating load. The solar collector must be set in the optimum tilt angle and direction to take daily solar radiation maximally, and the flow rate of heat transfer fluid through the solar collector should be kept in the optimum range. In this research, the performance tests of a capillary tube solar collector were performed to determine the optimum water flow rate and the results summarized as follows. 1. The regressive equations for efficiency estimations of the capillary tube solar collector in the open loop were modeled in the water flow rate of 700-l,000 $\ell$/hr. 2. The optimum water flow rate of the solar collector was estimated by the second order polynomial regression and the maximum efficiency was 80% at the water flow rate of 850 $\ell$/hr. 3. The solar thermal storage system consisted of a capillary tube solar collector and a water storage tank was tested at the water flow rate of 850 $\ell$/hr in the closed loop, and obtained the solar thermal storage efficiency of 55.2%. 4. As the capillary tube solar collector engaged in this experiment was made of non-corrosive polyolefin tubes, its weight was as light as 1/30 of the flat plate solar collector made of copper tubes. Therefore it was considered to be suitable for the greenhouse heating system.
'창방조생 ' 과 '미백' 복숭아의 저장기간중 중량감모율은 상온무포장에서 4일후 각각 6.8%, 4.9% 이었으나 저온 (0~2$^{\circ}C$), 고습(95$\pm$3%) 조건에서 PE 무천공필름 포장저장구는 25일째 모두 1% 이내였다. 복숭아 저장중 경도변화는 상온에 비해 저온저장에서는 모두 큰 차이가 없었다. 두 품종 모두 저장기간중의 유기산과 가용성 고형분은 큰 차이를 나타내지 않았다. '칭방조생'과 '미백' 의 fructose, glucose 함량은 두 품종 모두 지장전보다 약간씩 증가였으나 Sucruse 함량은 25일 이후 감소하는 경향이었다. 복숭아는 30$\mu\textrm{m}$ LDPE fim 또는 25$\mu\textrm{m}$ SM60 film으로 포장하여 저온(0~2$^{\circ}C$), 고습(95$\pm$3%) 조건에서 저장할 경우 '창방조생'은 20일, '미백'은 25일까지 저장 가능하였다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.