• Journal of Pharmaceutical Investigation
• /
• 제19권2호
• /
• pp.87-92
• /
• 1989

The multilayered monolithic type transdermal delivery device has been designed and analyzed by a numerical analysis. The device consists of three layered polymer matrices which posess the different diffusion parameters, respectively. The purpose of this study was to design an ideal transdermal drug delivery device which is capable of initial burst and zero order release later on. Numerical modelings were simulated for a dispersed and a dissolved multilayered monolithic system. The results showed that the dispersed multilayered monolithic system could meet the requirements for an ideal transdermal delivery device.

• ETRI Journal
• /
• 제18권3호
• /
• pp.181-193
• /
• 1996

A blue light emitting device has been successfully fabricated using a polymer with regulated conjugation length containing trimethylsilyl substituted phenylenevinylene units. Electroluminescence from the device has an emission maximum at 470 nm. The device shows typical diode characteristics with operating voltage of 20 V and the light becomes visible at a current density of less than $0.5;mA/cm^2$. The electroluminescence spectrum is virtually identical with the photoluminescence spectrum, indicating that the radiation mechanisms are the same for both. A light emitting device using the blend of a large band gap polymer and a small band gap polymer was also fabricated. Light emission from the small band gap polymer shows much improved quantum efficiency, but there is no light emission from the large band gap polymer. Quantum efficiency of the blend increases up to about two orders of magnitude greater than that of the small band gap polymer with increasing proportion of the large band gap polymer. The improvement in quantum efficiency is interpreted in terms of exciton transfer and the hole blocking behaviour of the large band gap polymer. Finally, we have fabricated a patterned flexible light emitting device using the high quantum efficiency polymer blend system.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2011년도 춘계학술발표대회
• /
• pp.66.2-66.2
• /
• 2011

A polymer-based multi-walled carbon nanotube (MWCNT) field emission device was fabricated from a composite dispersion of MWCNTs and waterborne polymethyl methacrylate (PMMA). The waterborne PMMA synthesized through the emulsion polymerization method was added to minimize the reagglomeration of dispersed MWCNTs with surfactants in water, and increase the adhesion between the and the substrate. The field emission properties of the fabricated device were optimized by adjusting the density of the emitter and the adhesion between the MWCNTs and the substrate. These were done by controlling the polymer concentration added to the MWCNT dispersion, as well as the amount of spray coating on the substrate. The results confirm the successful fabrication of a polymer-based MWCNT field emission device with a low field of 1.07 $V/{\mu}m$ and a good electric field enhancement factor of 2445. The device was fabricated by adding 0.8 mg/mL of polymer solution to the MWCNT dispersion and applying 20 cycles of spray coating. Application of this same MWCNT/polymer composite solution to a flexible polymer substrate also resulted in the successful fabrication of an electric field emission device with uniform emission and long time stability.

• 한국고분자학회:학술대회논문집
• /
• 한국고분자학회 2006년도 IUPAC International Symposium on Advanced Polymers for Emerging Technologies
• /
• pp.231-231
• /
• 2006

We fabricated a polymer sub-microstructure for optical device application by two-photon-induced laser lithography technique. Polymer pattern could be minimized as small as ${\sim}100\;nm$. The photopolymerization resin contains laser-dye, thus promising a high level of the optical gain. We utilized the lithography technique to the photonic crystal application, where the template of the two-dimensional photonic crystal was modified by polymer gain medium as defect-shape and line-shape orientations. Photonic band gap effect from polymer-doped photonic crystals is expected to exploit the application such as organic solid-state laser device.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2000년도 제1회 학술대회 논문집
• /
• pp.125-126
• /
• 2000

We report the use of fluorene based copolymers containing quinoline(POF66, PIF66) and pyridine(PFPV) units as electron transporting polymers for multi-layered LEDs. Double-layer device structure combining PIF66 as electron-transporting layer with the emissive MEHPPV showed a maximum quantum efficiency of 0.03%, which is 30 fold increased compared with ITO/MEHPPV/Al single-layer device. PFPV layer increased the quantum efficiency up to 0.1% in the device structure of ITO/(P-3:PVK)/PFPV/Al. The ETL with the electron deficient moiety improved the LED performance by the characteristics of electron transporting as well as hole blocking between emissive layer and metal cathode.

• ETRI Journal
• /
• 제24권4호
• /
• pp.259-269
• /
• 2002

Polymers are emerging as new alternative materials for optical communication devices. We developed two types of polymer-based devices for optical communications. One type is for ultra high-speed signal processing that uses nonlinear optical (NLO) polymers in such devices as electro-optic (EO) Mach-Z${\ddot{e}} $ hnder (MZ) modulators and EO 2${\times}$2 switches. The other is for WDM optical communications that use low-loss optical polymers in such devices as 1${\times}$2, 2${\times}$2, 4-arrayed 2${\times}$2 digital optical switches (DOSs) and 16${\times}$16 arrayed waveguide grating (AWG) routers. For these devices, we synthesized a polyetherimide-disperse red 1 (PEI-DR1) side chain NLO polymer and a low-loss optical polymer known as fluorinated polyaryleneethers (FPAE). This paper presents the details of our development of these polymeric photonic devices considering all aspects from materials to packaging.

• 정보저장시스템학회논문집
• /
• 제11권2호
• /
• pp.36-40
• /
• 2015

The demand for flexible devices including solar cells, memories and batteries has increased rapidly over the past decades. In most flexible devices, polymer-based materials are used to enable the mechanical deformations such as bending or folding. Shape Memory Polymers (SMPs) is a high molecular compound polymer with flexibility and shape recovery characteristics. In this work, flexible shape memory device was fabricated by simply coating the conducting material, carbon nano-tube (CNT), on a shape memory polymer. Furthermore, durability of the device under various type of mechanical deformations was assessed. It is believed that the result of this work will aid in realization of a stretchable and wearable electronic device for practical applications.

• Current Optics and Photonics
• /
• 제3권1호
• /
• pp.66-71
• /
• 2019

Application of liquid crystal (LC) materials to a flexible device is challenging because the bending of LC displays easily causes change in thickness of the LC layer and orientation of LCs, resulting in deterioration in a displayed image quality. In this work, we demonstrate a prototype device combining a flexible polymer substrate and an optically isotropic LC-polymer composite in which the device consists of interdigitated in-plane switching electrodes deposited on a flexible colorless polyimide substrate and the composite consisting of nano-sized LC droplets in a polymer matrix. The device can keep good electro-optic characteristics even when it is in a bending state because the LC orientation is not disturbed in both voltage-off and -on states. The proposed device shows a high potential to be applicable for future flexible LC devices.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2007년도 추계학술발표대회 및
• /
• pp.26.1-26.1
• /
• 2007

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집 Vol.14 No.1
• /
• pp.61-64
• /
• 2001

This study relates to a method for manufacturing a solid electrolytic capacitor using a functional polymer composition. The method comprises immersing the rolled aluminum electrolytic capacitor device in polyaniline solution with high electric conductivity to impregnate the device with polyaniline, drying the impregnated device in a drying oven which is maintained at constant temperature to fully remove the solvent, inserting the dried device to a capacitor aluminum can and then sealing with epoxy resin, to manufacture a solid electrolytic capacitor using a conducting polymer. As such, the impregnation can be performed well at not only normal temperature and pressure, but also high temperature and reduced pressure. The solid electrolytic capacitor has the advantages of high capacity, low impedance and low ESR, and also, low manufacturing cost, simple processes and high reliability.