• Korea-Australia Rheology Journal
• /
• 제11권4호
• /
• pp.305-311
• /
• 1999

The shear behavior of polymers obtained by means of devices such as capillary and cone-and-plate rheo-meters is commonly used to assess their processing performance and as a characterization tool. However, the number of instances when two polymers have the same shear properties but perform differently during certain types of processing operations (e.g. film blowing and sheet extrusion) indicate that shear properties alone may not be sufficient to characterize polymeric fluids. We begin by defining the kinematics of shear-free or extensional flow and the associated material functions. The extensional and shear behavior of three different types of polyethylene (PE) are then compared to illustrate the points that one cannot ascertain the extensional properties of polymer melts from their shear properties and, furthermore, there may not be a simple relation between properties obtained from one type of extensional flow and those of another type. The kinematics of most processing flows are extensional rather than shear in nature, and , hence, the performance of polymers during processes such as fiber spinning, film casting, film blowing, thermoforming, blow molding, and even extrusion is more readily accounted for through extensional viscosity measurements. Methods for carrying out extensional flow measurements are then reviewed including approximate methods. To illustrate the sensitivity of extensional viscosity measurements to subtle changes in the molecular architecture of PEs, results are presented for samples with a narrow molecular weight distribution but with varying numbers of long chain branches. Finally, constitutive equations which allow one to separate shear and extensional flow behavior are discussed as any attempts to simulate the subtle processing differences between two polymers will require constitutive equations of this nature.

• Structural Engineering and Mechanics
• /
• 제50권6호
• /
• pp.817-834
• /
• 2014

An experimental program was designed in the current work to examine the structural behavior of ferrocement beams reinforced with composite materials under three point loadings up to failure. The experimental program comprised casting and testing of twelve ferrocement beams having the dimensions of 120 mm width, 200 mm depth and 1600 mm length. The twelve beams were different in the type of reinforcements; steel bars, traditional wire meshes (welded and expanded wire meshes) and composite materials (fiberglass wire meshes and polypropylene wire meshes). The flexural performances of the all tested beams in terms of strength, ductility, cracking behavior and energy absorption were investigated. Also all the tested beams were simulated using ANSYS program. The results of the experimental tests concluded that the beam with fiber glass meshes gives the lowest first crack load and ultimate load. The ferrocement beam reinforced with four layers of welded wire meshes has better structural behavior than those beams reinforced with other types of wire meshes. Also the beams reinforced with metal wire meshes give smaller cracks width in comparing with those reinforced with non-metal wire meshes. Also the Finite Element (FE) simulations gave good results comparing with the experimental results.

• Bulletin of the Korean Chemical Society
• /
• 제31권9호
• /
• pp.2637-2643
• /
• 2010

In order to develop a new line injection system for spin draw yarn (FD SDY) fibers, the effect of various parameters in extrusion and melt line conditions on the dispersion and distribution of $TiO_2$ particles within FD PET fibers was investigated. As a result, the dispersibility of $TiO_2$ particles in a PET matrix is found to depend on the particle size and its surface characteristics. Surface modification of $TiO_2$ by dimethyl polysiloxane resulted in the improved dispersibility and affinity of $TiO_2$ particles in the PET matrix. Especially, residence time, mixing temperature, and mixing shear rate in the new line injection system under the SDY spinning process were very important parameters to minimize the agglomeration of $TiO_2$ particles. The FD SDY prepared by the new line injection system was superior to those using the polymerization process and the conventional masterbatch chip dosing process in the color-L and color-b values of the fibers.

• KIEE International Transactions on Electrophysics and Applications
• /
• 제2C권6호
• /
• pp.309-313
• /
• 2002

In this paper, we have studied minimization of the kerf-width and surface burning, which occurred after the conventional singulation process of the multi-layer BGA board with copper, polyethylene and epoxy glass fiber. The high thermal energy of a pulsed Nd:YAG laser is used to cut the multi-layer board. The most considerable matter in the laser cutting of the multi-layer BGA boards is their different absorption coefficient to the laser beam and their different heat conductivity. The cut mechanism of a multi-layer BGA board using a 2$^{nd}$ harmonic Nd:YAG laser is the thermal vaporization by high temperature rise based on the Gaussian profile and copper melting point. In this experiment, we found that the sacrifice layer and Na blowing are effective in minimizing the surface burning by the reaction between oxygen in the air and the laser beam. In addition, N2 blowing reduces laser energy loss by debris and suppresses surface oxidation. Also, the beam incidence on the epoxy layer compared to polyimide was much more suitable to reduce damage to polyimide with copper wire for the multi layer BGA singulation. When the polyester double-sided tape is used as a sacrifice layer, surface carbonization becomes less. The SEM, non-contact 3D inspector and high-resolution microscope are used to measure cut line-width and surface morphology.

• 한국소음진동공학회논문집
• /
• 제18권2호
• /
• pp.247-254
• /
• 2008

Resilient materials are generally used for the floating floors to reduce the floor impact sound. Dynamic stiffness of resilient material, which has the most to do with the floor impact sound reduction. The resilient materials available in Korea include EPS(styrofoam), recycled urethane types, EVA(ethylene vinylacetate) foam rubber, foam PE(polyethylene). glass fiber & rock wool, recycled tire, foam polypropylene. compressed polyester, and other synthetic materials. In this study, we tested dynamic stiffness of resilient material and floor impact sound reduction characteristic to a lot of kinds of resilient materials. It was found that dynamic stiffness of multi-layered damping material could be estimated if know value of each layer that compose whole structure. And the test showed that the amount of the heavy-weight impact sound reduction appeared by being influenced from this dynamic stiffness of resilient material. The dynamic stiffness looked like between other resilient materials, a similar to the amount of the heavy-weight impact sound reduction was shown.

• 한국물환경학회지
• /
• 제22권5호
• /
• pp.865-870
• /
• 2006

The behavior and influence of EPS on membrane fouling by changing of hydraulic retention time was investigated, using lab. scale submerged membrane bio-reactor, which was operated with gravitational filtration and fed supernatant of primary sedimentation in waste water treatment plant as influent. The membrane was adopted micro-filter of polyethylene hollow fiber. EPS was analysed as polysaccharides and protein especially, into soluble and bound EPS separately. The concentration of soluble EPS was increased at short HRT, then membrane fouling was rapidly progressed and flux was depressed. The most of EPS clogged membrane pore were polysaccharides, while protein was important parameter affected on membrane fouling because of it's more accumulating in the more term operating.

• 한국안전학회지
• /
• 제20권1호
• /
• pp.1-6
• /
• 2005

Stick type ignition coil is new development that connect directly with ECU(Electronic control unit), without needing a spark plug cable and distributor. Glass-fiber reinforced ploymeric composites provide the desirable properties of high stiffness and strength as well as low specific weight. Stick type ignition coil jacket is using PBT CF30 resin. PBT CF30 resin is a kind of electric insulation which is a superior engineering plastic that is used to prevent the leakage of the electrical current. If PET receive a mistake of design or excessive force when HV terminal oppress on jacket, it can happen to crack. Local stress concentrations occurring on the contact surface, the contact phenomenon becomes a direct cause to the wear and failure of mechanical structures. When it is cracked, it can allow a leakage of the electrical current. So, in this study, we analyze the contact stress to PBT jacket using ANSYS program, when HV terminal oppress on jacket. We suppose PBT to be Jacket and we analyzed contact stress that happens in PET like PBT analysis method. We compared the use of PBT and PET.

• The Korean Journal of Ceramics
• /
• 제4권4호
• /
• pp.382-386
• /
• 1998

titanate and a silicon carbide/zirconium diboride particulate composite have each been blended with thermoplastic of aqueous binders and extruded. The green extrudates have diameters ranging between 50 and 150 ㎛ and polyethylene-base 150 ${\mu}m$ diameter fibers can be drawn down at elevated temperature to approximately 40 ${\mu}m$ diameter. Hollow fibers with 150${\mu}m$ outer and 90 ${\mu}m$ inner diameter can also be fabricated. Green fibers have been processed into chopped fiber felts for use as gas distributors/current collectors in an experimental solid oxide fuel cell (SOFC) and the first attempts at producing simple textile structures have been successful. The fibers, tubes and felts have been successfully debound and sintered and characterization of the sintered PSZ fibers, for example, has revealed a density in excess of 99% and tensile failure stresses up to 1.0 GPa for 78 ${\mu}m$ diameter fibers.

• Fibers and Polymers
• /
• 제5권4호
• /
• pp.264-269
• /
• 2004

The present paper deals with improvement in disperse dyeablility as well as imparting of cationic dyeablility to difficultly dyeable polypropylene by a melt blending technique. Isotactic polypropylene (PP) was blended with fibre grade polybutylene terephthalate (PBT), cationic dyeable polyethylene terephthalate (CDPET) and polystyrene (PS), individually. The resulting binary blends were spun and drawn into fibres at draw ratio 2, 2.5, and 3. The compatibility of blends, structural changes of fibres in terms of X-ray crystallinity, relative crystallinity, sonic modulus, birefringence and thermal stability were examined. The blended fibres were found to be disperse dyeable by the conventional method of high temperature and high pressure dyeing. And this dye ability increased with increase in the level of substitution. PP/CDPET blend also exhibited dyeablility with cationic dyes in addition to that with disperse dyes. The optimum level of blending was predicted keeping in view of tenacity and thermal stability of melt blend fibres. The wash fastness properties of the dyed fibres were found to be of high rate.

• 한국식품영양과학회지
• /
• 제29권2호
• /
• pp.218-223
• /
• 2000

The objective of this study was to investigate the effectiveness of preservatives for extending storage life and maintaining the quality of minimally processed Chinese cabbage. Cut Chinese cabbage was treated with either 1% CaCl2, 1% NaCl, 3% sucrose, 1% Ca-lactate, 1% vitamin C, 0.05% chitosan＋1% vitamin C, 0.1% Sporix＋1% vitamin C or hot water(6$0^{\circ}C$) and then packed with polyethylene film(60${\mu}{\textrm}{m}$) and stored at either 2$0^{\circ}C$ or 4$^{\circ}C$. To evaluate biochemical changes and quality of minimally processed Chinese cabbage, the samples were tested to determine the amount of vitamen C, titratable acidity, organic acid and fiber contents. Changes in color were also examined. The quality of kimchi prepared form minimally processed cabbage was affected by the treatments. REsults indicate that the minimally processed Chinese cabbage treated with either 1% CaCl2 at 2$0^{\circ}C$ and 4$^{\circ}C$ or 1% NaCl at 2$0^{\circ}C$ minimized biochemical changes in plant tissue and those treatments were most effective in maintaining product quality. The cabbage treated with 1% vitamin C or 1% NaCl at 4$^{\circ}C$ resulted in kimchi with improved color, texture, flavor and the best overall acceptability, as determined by a sensory test.