• Macromolecular Research
• /
• v.17 no.7
• /
• pp.516-521
• /
• 2009

Techflex$^{(R)}$, a polypropylene-lined, multilayer infusion bag, was studied for its compatibility with diazepam, in comparison to the conventional infusion bag, Safeflex$^{(R)}$, which is comprised of poly(vinyl chloride) (PVC). Diazepam was diluted in 0.9% sodium chloride isotonic solution and stored in the infusion bags for 24 h. To evaluate the sorption of diazepam into the infusion bags during storage, the concentration of the drug remaining in the bag was measured using gas chromatography-mass spectroscopy. The PVC bags exhibited a marked sorption of diazepam, with a drug loss reaching up to 90% of the initial concentration after 24 h of contact, whereas Techflex$^{(R)}$ inhibited the drug sorption, showing approximately 10%, under the same conditions. The differences in the sorption behaviors of the bags are discussed in terms of solubility parameters and crystallinities of the polymers.

• Polymer(Korea)
• /
• v.28 no.6
• /
• pp.468-477
• /
• 2004

The polymer blends of waste poly(vinyl chloride) (RPVC) and waste polyethylene (RPE) were prepared by melt mixing. Various ethylene-vinyl acetate copolymers (EVA) and ethylene-methacrylic acid Na salt copolymer (ionomer) were used as compatibilizer. Their morphologies and mechanical properties were evaluated as a funtion of mixing sequence and time. EVA with high vinyl acetate contents showed a rapid increment of tensile properties when small amount was added. Tensile properties of the blends were gradually increased with the addition of ionomer. Morphologies of RPVC/RPE blends were analyzed by scanning electron microscopy. FT-IR data showed that EVA was a good compatibilizer in RPVC/RPE blend compared to ionomer. Mechanical properties of the blends were highly enhanced when RPVC and compatibilizer were mixed and first RPE was added later.

• Applied Chemistry for Engineering
• /
• v.17 no.2
• /
• pp.229-234
• /
• 2006

The effect of ZnO in the decomposition of poly(vinyl chloride) (PVC) and polystyrene (PS) mixtures in air atmosphere has been studied by thermogravimetry (TG) and gas chromatograph-mass spectrometry (GC-MS) under various mixing ratios and reaction temperatures. From this work, it can be seen that the yields of a liquid product were increased with the increase of PS in mixtures, whereas those of gaseous products were decreased. And the yields of a gaseous product and HCl were decreased with the increase of ZnO in mixtures. It was also found that HCl was rarely produced at ZnO/Mixture = 0.5 by the effect of ZnO in dehydrochlorination of PVC.

• Applied Chemistry for Engineering
• /
• v.9 no.2
• /
• pp.177-184
• /
• 1998

The contact angle on powder hydrophobic polymer PMMA(polymethylmethacrylate), PVC(poly vinyl chloride) and hydrophilic metal aluminium was measured by wicking method on the base of Washburn equation for water, glycerol, formamide, diiodomethane, 1,1,2,2-tetrabromoethane, 1-bromonaphthalene, acetone, chloroform, benzene, ethanol, methanol, and for anionic surfactant SDS(sodium dodecyl sulfate) and cationic surfactant CATB(cetyl trimethylamonium bromide) aqueous solution with concentrations. The values of ${\gamma}_c$ estimated by Zisman plot and adhesion tension plot for contact angle with organic liquids, SDS, and CTAB aqueous solutions were 43.5, 28.3, and $36.2mNm^{-1}$ for PMMA and 44.2, 25.0, and $34.8mNm^{-1}$ for PVC, respectively. From the results, it was considered that wettability and characteristics of solid surface were transformed by adding surfactant. The surface free energy, ${\gamma}_s$ and its components of PMMA, PVC, and aluminium were determined using harmonic equation.

• Bulletin of the Korean Chemical Society
• /
• v.26 no.1
• /
• pp.51-56
• /
• 2005

A PVC membrane electrode for lead ion based on 1-phenyl-2-(2-quinolyl)-1,2-dioxo-2-(4-bromo) phenylhydrazone (PQDBP) as ionophore was demonstrated. The optimum composition of the membrane was 30 wt% poly(vinyl chloride), 60 wt% dibutyl phthalate as a plasticizer, 4 wt% ionophore and 6 wt% sodium tetraphenylborate as additive. The electrode exhibits a Nernstian response (28.7 mV decade$^{-1}$) for Pb$^{2+}$ over a wide concentration range (1.0 ${\times}$ 10$^{-1}$ to 1 ${\times}$ 10$^{-6}$ M) with a detection limit of 6.0 ${\times}$ 10$^{-7}$ M. This sensor has a short response time and can be used for at least 2 months without any divergence in potentials. The proposed electrode could be used in a pH range of 3.0-6.0 and revealed good selectivities for Pb$^{+2}$ over a wide variety of other metal ions. It was successfully applied as an indicator electrode for the potentiometric titration of lead ion with potassium chromate and for the direct determination of lead in mine.

• Journal of the Korean Electrochemical Society
• /
• v.9 no.1
• /
• pp.29-33
• /
• 2006

A new porous separator based on poly(vinyl chloride) (PVC)/poly(vinylidene fluoride-co-hexafluoro-propylene) (P(VdF-co-HFP)/poly(methyl methacrylate) (PMMA) was prepared by a phase inversion method. To enhance mechanical property, the membrane was stretched uniaxially at high temperature. Tensile strength and ionic conductivity were measured for various draw ratios. The tensile strength and ionic conductivity were increased with increasing draw ratio. The tensile strength of the separator reached 52MPa after stretching to draw ratio of 5, and the ionic conductivity of the separator was increased from $1.9Xs10^{-4}S/cm\;to\;4.6X10^{-4}S/cm\;at\;25^{\circ}C$. The stretched separator immersed in liquid electrolyte was electrochemically stable up to 4.7 V. The cell based on the stretched separator was maintained at about 99% of the initial discharge capacity after 10th cycle operation at 0.2C rate.

• Journal of the Korean Electrochemical Society
• /
• v.10 no.2
• /
• pp.82-87
• /
• 2007

New porous separators based on non-polyolefin materials including the blend of poly (vinyl chloride) (PVC)/poly (vinylidene fluoride-co-hexafluoropropylene) (P(VdF-co-HFP)/poly(methyl methacrylate) (PMMA), and the porous separator based on poly (vinylidene fluoride) (PVdF) were prepared by phase inversion method. The porosity and morphology were controlled with phase inversion rate, which is governed by the relative content of non-solvent and solvent in coagulation bath. To enhance tensile strength, the solvent pre-evaporation and uni-axial stretching processes were applied. The ionic conductivity was increased with increasing stretching ratio, and tensile strength was increased with increasing solvent pre-evaporation time and stretching ratio. The 200% stretched PVdF separator showed 56 MPa of tensile strength, and the ionic conductivity of the stretched PVdF separator was $8.6{\times}10^{-4}\;S\;cm^{-1}\;at\;25^{\circ}C$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.1
• /
• pp.93-97
• /
• 2023

A triboelectric nanogenerator (TENG) is a device that converts mechanical energy into electrical energy, and has been considered as a substitute for continuous power supply due to its high performance, simple structure and eco-friendliness. Recently, it is important to develop a TENG using a non-toxic material in order to use it as a power source for wearable, attachable, and body-embeddable electronics. Here, we developed a human friendly TENG using polyvinyl chloride (PVC) gel containing acetyl tributyl citrate (ATBC), a non-toxic plasticizer. PVC gels were fabricated using various ratios of PVC and ATBC, and optimized by investigating dielectric properties, surface potential, output performance, and durability. The PVC gel based TENG generates output signals of 73 V and 4.3 μA, i.e., a 5-fold enhancement in the output power compared to pristine PVC-based TENG. In addition, the PVC gel can be stretched over 500% of strain. This study is expected to be helpful in the future development of non-toxic wearable TENG.

• Membrane Journal
• /
• v.21 no.2
• /
• pp.193-200
• /
• 2011

An amphiphilic graft copolymer comprising a poly(vinyl chloride) (PVC) backbone and poly (styrene sulfonic acid) (PSSA) side chains (PVC-g-PSSA) was synthesized via atom transfer radical polymerization (ATRP). Mesoporous titanium dioxide $(TiO_2)$ films with crystalline anatase phase were synthesized via a sol-gel process by templating PVC-g-PSSA graft copolymer. Titanium isopropoxide (TTIP), a $TiO_2$ precursor was selectively incorporated into the hydrophilic PSSA domains of the graft copolymer and grew to form mesoporous $TiO_2$ films, as confirmed by scanning electron microscopy (SEM) and X-ray diffraction (XRD) analysis. The performances of dye-sensitized solar cell (DSSC) were systematically investigated by varying spin coating times and the amounts of P25 nanoparticies. The energy conversion efficiency reached up to 2.7% at 100 mW/$cm^2$ upon using quasi-solid-state polymer electrolyte.

• Membrane and Water Treatment
• /
• v.9 no.6
• /
• pp.385-392
• /
• 2018

Poly vinyl chloride (PVC) was chemically modified, and used for ultrafiltration to analyze the performance. Non-solvent induced phase separation (NIPS) method was used to prepare membranes. The neat PVC membrane was casted and used as a control membrane. Modified membrane was prepared by reacting PVC with ethanolamine (EA) in the casting solution (labeled as CM-PVC). Pure water permeability (PWP) was evaluated by measuring pure water flux. Humic acid was used as model foulant solute to analyze flux and rejection ability of membranes. Flux and rejection data of neat and modified membranes were compared to prove the improvement in the filtration performance. The experimental results showed that for PVC and CM-PVC, PWP was calculated to be ~64 and ${\sim}143L/m^2{\cdot}h$, respectively, and the rejection of humic acid was found to be 98% and 100%, respectively. TGA was carried out to analyze the effect of chemical modification on the thermal stability of polymer. FT-IR analysis was another characterization technique used for the comparative study.