• Journal of Biosystems Engineering
• /
• 제42권4호
• /
• pp.350-357
• /
• 2017

Purpose: In-situ monitoring of water quality is fundamental to most environmental applications. The high cost and long delays of conventional laboratory methods used to determine water quality, including on-site sampling and chemical analysis, have limited their use in efficiently managing water sources while preventing environmental pollution. The objective of this study was to develop an on-site water monitoring system consisting mainly of an Arduino board and a sensor array of multiple ion selective electrodes (ISEs) to measure the concentration of $NO_3$ ions. Methods: The developed system includes a combination of three ISEs, double-junction reference electrode, solution container, sampling system consisting of three pumps and solenoid valves, signal processing circuit, and an Arduino board for data acquisition and system control. Prior to each sample measurement, a two-point normalization method was applied for a sensitivity adjustment followed by an offset adjustment to minimize the potential drift that could occur during continuous measurement and standardize the response of multiple electrodes. To investigate its utility in on-site nitrate monitoring, the prototype was tested in a facility where drinking water was collected from a water supply source. Results: Differences in the electric potentials of the $NO_3$ ISEs between 10 and $100mg{\cdot}L^{-1}$ $NO_3$ concentration levels were nearly constant with negative sensitivities of 58 to 62 mV during the period of sample measurement, which is representative of a stable electrode response. The $NO_3$ concentrations determined by the ISEs were almost comparable to those obtained with standard instruments within 15% relative errors. Conclusions: The use of the developed on-site nitrate monitoring system based on automatic sampling and two-point normalization was feasible for detecting abrupt changes in nitrate concentration at various water supply sites, showing a maximum difference of $4.2mg{\cdot}L^{-1}$ from an actual concentration of $14mg{\cdot}L^{-1}$.

• 한국공작기계학회논문집
• /
• 제14권2호
• /
• pp.21-26
• /
• 2005

From on the machining center cutting work of 5534, the characteristics such as spindle speed and feed speed fir the third point height, average spacing of roughness peaks, bearing ratio, center line average, ten point height. experiments is roughness for sampling length determine to measuring length of cutting feed speed 200, 400, 600, 800mm/min and spindle speed 800, 1000, 1200, 1400rpm. Third point height is spindle speed with most suitable cutting condition 1000rpm. Third point height is feed speed with most suitable cutting condition 400mm/min. Average spacing of roughness peaks are spindle speed with most suitable cutting condition feed speed increased to average spacing of roughness Peaks are increased. Spindle speed increased to average spacing of roughness peaks are decreased. Bearing ratio is spindle speed with feed speed increased to bearing ratio decreased. Center line average is spindle speed with most suitable cutting condition at 1200rpm feed speed with most suitable cutting condition at 200mm/min to cutting foe roughness suddenly decreased. Ten point height is spindle speed with most suitable cutting condition 1200rpm at ten point height cutting face roughness to decreased and feed speed with most suitable cutting condition 800mm/min at ten point height cutting face roughness to decreased.

• 한국산림과학회지
• /
• 제17권1호
• /
• pp.35-42
• /
• 1973

천연활엽수림(天然闊葉樹林)은 수형(樹型)이 불규칙(不規則)하며 이용가치(利用價値)도 떨어진다. 우리나라에서의 활엽수림(闊葉樹林)은 대체(大體)로 오지(奧地)에 위치(位置)하고 있으며 개발(開發)에 문제점(問題點)이 허다(許多)하겠으나 총축적량(總蓄積量)이 부족(不足)한 현금(現今) 이의 개발이용(開發利用)의 필요성(必要性)이 대두(擡頭)되고 있다. 이러한 시점(時點)에서 본(本) 연구(硏究)는 천연활엽수(天然闊葉樹) 조사(調査)에 알맞은 추출법(抽出法)을 구명(究明)하므로서 조사사업(調査事業)에 이바지할 수 있다고 하겠다. 본(本) 조사(調査)는 1. 10ha되게 3개소(個所)를 선정(選定)하고 이를 대상(對象)으로 4가지 추출법(抽出法)을 적용(適用)하여 0.1ha($20m{\times}50m$) 구형표본점(矩形標本點) 6개(個) 즉(卽) 6%의 추출율(抽出率)로 표본(標本)을 추출(抽出) 조사(調査)하였는데 조사결과(調査結果)는 표(表) 1과 같으며 적용(適用)된 추출법(抽出法)은 (1) 격자법(格子法)에 의(依)한 임의추출법(任意抽出法) (2) 좌표법(座標法)에 의(依)한 임의추출법(任意抽出法) (3) 선표본점법(線標本點法) (4) 부차추출법(副次抽出法)이다. 2. 1:15, 000 항공사진(航空寫眞)을 이용(利用)하여 위 지역(地域)을 포함(包含)하는 지역(地域)에서 150ha 되게 구획(區劃)한 후(後) Mirror Stereoscope로 임상(林相)을 구분(區分)하였다. 경급(經級)과 소밀도(疎密度)를 기준(基準)으로 구분(區分)하였더니 3계급(階級)으로 나눠졌는데 150ha에서 계통적(系統的)으로 7개(個)(추출율(抽出率) 0.46%)의 표본점(標本點)을 배치(配置)하고 현지(現地)에서 0.1ha 원형표본점(圓形標本點)을 조사(調査)하였는데 그 결과(結果)는 표(表) 4와 같다. 3. 추출법(抽出法)에 따른 값과 매목조사결과(每木調査結果)(모평균(母平均))와를 비교(比較)하였더니 유의차(有意差)가 없었다(표(表3)). 4. 이상(以上)의 결과(結果)로 다음과 같은 결론(結論)을 얻었다. 1) 격자법(格子法)과 선표본점법(線標本點法)에 의(依)한 조사(調査)가 타추출법(他抽出法)에 비(比)하여 양호(良好)하다. 2) 원형표본점(圓形標本點)을 사용(使用)했을때는 구형표본점(矩形標本點)을 사용(使用)했을때 보다 과대치(過大値)를 가져온다. 3) 천연활엽수림(天然闊葉樹林)은 임목(林木)이 고르게 서있지 않으므로 표본점(標本點)의 수(數)를 적게 취(取)하면 오차가 커질 위험(危險)이 있다.

• 한국정보과학회논문지:소프트웨어및응용
• /
• 제36권11호
• /
• pp.947-954
• /
• 2009

본 논문은 입력받은 다수 이미지의 Visual Hull을 이용하여 Surfel 기반의 물체를 복원하는 새로운 방법을 제안한다. Sufel은 포인트 집합면을 효과적으로 근사하여 나타내는 포인트 표현 단위이다. LDC(Layered Depth Cube) Surfel 샘플링 방식에 입력 이미지로부터 근사되는 형상을 대표하는 Visual Hull의 개념을 연동하여 이미지로부터 물체의 Surfel 기하 정보를 생성할 수 있다. Surfel 표현 방식은 기존의 폴리곤 기반 방식에 비해 상대적으로 적은 메모리를 소모하고 LDC 해상도를 자유롭게 바꿀 수 있기 때문에, 대상 물체를 복원하는 품질을 조절 가능하며, 주어진 메모리 자원에 대해서 최대의 품질을 가진 결과를 얻을 수 있다.

• 전기학회논문지
• /
• 제59권5호
• /
• pp.897-903
• /
• 2010

This paper presents a response surface method(RSM) with Latin Hypercube Sampling strategy, which is employed to optimize a magnet pole shape of large scale BLDC motor to minimize the cogging torque. The proposed LHS algorithm consists of the multi-objective Pareto optimization and (1+1) evolution strategy. The algorithm is compared with the uniform sampling point method in view points of computing time and convergence. In order to verify the developed algorithm, a 6 MW BLDC motor is simulated with 4 design parameters (arc length and 3 variables for magnet) and 4 constraints for minimizing of the cogging torque. The optimization procedure has two stages; the fist is to optimize the arc length of the PM and the second is to optimize the magnet pole shape by using the proposed hybrid algorithm. At the 3rd iteration, an optimal point is obtained, and the cogging torque of the optimized shape is converged to about 14% of the initial one. It means that 3 iterations aregood enough to obtain the optimal design parameters in the program.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집B
• /
• pp.48-52
• /
• 2001

In this paper presents an accurate AFM used that is free from the Z-directional distortion of a servo actuator is described. Two mathematical correction methods by the in-situ self-calibrationare employed in this AFM. One is the method by the integration, and the other is the method by inverse function of the calibration curve. The in situ self-calibration method by the integration, the derivative of the calibration curve function of the PZT actuator is calculated from the profile measurement data sets which are obtained by repeating measurements after a small Z-directional shift. Input displacement at each sampling point is approximately estimated first by using a straight calibration line. The derivative is integrated with reference to the approximate input to obtain the approximate calibration curve. Then the approximation of the input value of each sampling point is improved using the obtained calibration curve. Next the integral of the derivative is improved using the newly estimated input values. As a result of repeating these improving process, the calibration curve converges to the correct one, and the distortion of the AFM image can be corrected. In the in situ self-calibration through evaluating the inverse function of the calibration curve, the profile measurement data sets were used during the data processing technique. Principles and experimental results of the two methods are presented.

• 한국ITS학회 논문지
• /
• 제10권1호
• /
• pp.67-75
• /
• 2011

본 논문은 기존의 단일값(점추정)으로 제시하던 검지기 성능평가 결과를 통계적 신뢰구간(구간추정)으로 제시하기 위한 검지기 성능평가 방안을 제시했다. 일반적으로 구간추정은 점추정에 비해 표본 통계의 더 많은 정보를 제공하기 때문에 기존 단일값으로 제시해 오던 검지기 성능평가 결과의 신뢰성을 향상시킬 수 있다. 방법론은 크게 표본 추출, 평가척도 분석, 평가결과 제시의 세 부분으로 나누어진다. 표본추출 방법에는 다양한 통계적 표본 추출 방법이 있지만 교통, 조도, 기상조건에 따라 변화하는 차량검지기 성능의 특성상 층화추출법이 통계적 신뢰구간 제시를 위한 가장 적합한 방법론으로 간주되었다. 또한 기존에 널리 사용된 검지기 성능평가 척도들의 특징을 면밀히 분석하여 평가자로 하여금 해당 검지자료에 적합한 평가척도를 선택할 수 있는 프로세스를 정립하였다. 마지막으로 평가기간 전체(예. 30분)와 개별분석 단위(예. 1분) 평가결과의 통계적 신뢰구간을 반영하기 위한 방법론을 제시했다. 본 연구는 기존 검지기 성능평가 결과의 단일값 제시로 인해 불가능 했던 신뢰구간 제시를 가능하게 함에 따라 검지기 성능평가 결과의 신뢰성을 향상시킬 수 있을 것으로 판단된다.

• 전산구조공학
• /
• 제7권1호
• /
• pp.109-116
• /
• 1994

구조물의 신뢰도를 평가하는 방법을 살표보고 각각의 장.단점을 비교한다. 각 방법의 정확성을 평가하는 기준으로는 Crude Monte Carlo(CMC)방법을 택하여 Importance Sampling(IS)방법, 그리고 Directional Simulation(DS) 방법을 살펴보고 1차 근사방법은 현재 많이 사용되고 있는 Rackwitz-Fiessler(RF)방법, Chen과 Lind가 제안한 3-parameter방법(CL), Hohenbichler가 제안한 Rosenblatt 변환방법(RT)을 그리고 2차 근사방법은 Breitung이 제안한 곡률적합 포물선 (Curvature Fitted Paraboloid, CFP) 공식과 Kiureghian이 제안한 점적합 포물선(Point Fitted Paraboloid, PFP)공식, 그리고 Log-Likelihood Function을 이용하여 원변수공간에서 파괴확률을 구하는 2차 근사공식(LLF)을 비교한다. 그리고 한계상태식이 불명확할 때 효율적으로 사용할 수 있는 반응응답법(Response sufrace method, RSM)을 살펴본다. 각 방법의 효율성 특히 적용 가능성을 예제를 통해 해석한 결과 추출법의 경우는 DS방법이, 그리고 근사방법에서는 RSM방법이 효율적임을 알 수 있다.

• 한국환경과학회지
• /
• 제26권4호
• /
• pp.467-481
• /
• 2017

This study sought to determine the changes in weather conditions in urban streets, along with conditions of traffic and roads in urban areas. The variations in weather conditions depending on traffic differed according to distance. First, the temperature difference measured by traffic results is as follows: T1 point $1.03^{\circ}C$, T2 point $1.04^{\circ}C$, T3 point $0.9^{\circ}C$, T4 point $1.01^{\circ}C$, and T5 point $0.31^{\circ}C$. The average difference between the measured temperatures by the point of measurement was $0.86^{\circ}C$. The changes in wind velocity according to traffic volume results of the measurements is T1 point 1.32 m/s, T2 point 0.80 m/s, T3 point 0.29 m/s, T4 point 0.04 m/s, and T5 point 0.09 m/s. The difference between the average wind speeds was 0.51 m/s and traffic jams caused substantial differences in distance. The relative humidity tended to be inversely proportional to temperature. The measurements results ares T1 point 2.29%, T2 point 2.67%, T3 point 2.47%, T4 point 2.16%, and T5 point 0.91% The difference between the average relative humidity was 7.3%. In case of independent sampling T test according to traffic volume, changes in wind velocity and temperature were directly proportional to the level of statistical significance(p<0.01). On the other hand, relative humidity tended to be inversely proportional; however, there was no statistical significance.

• 환경영향평가
• /
• 제16권6호
• /
• pp.525-532
• /
• 2007

In order to establish and implement the total maximum daily load (TMDL) management plan in Korea, it is necessary to set the source units and calculate discharge loads for non-point source pollutants such as BOD, COD, SS, TN and TP. This study analysed the corelation between stormwater runoff characteristics and event mean concentrations (EMCs) of non-point source pollutants. As the result of the corelation analysis, we knew that all the antecedent dry days (ADD) and the rainfall correlated lowly with non-point source pollutants in the urban areas such as resident area, industrial area, business area, road area and parking area. Therefore, it is necessary to get all samples from stormwater starting point to stormwater ending point and standardize the sampling method of stormwater in order to obtain more accurate EMCs for landuse.